Land Rover Defender Parts

Fuel Injector Bolt - retaining bolt securing the fuel injector clamp to the cylinder head on the 2.4L Duratorq TDCi (Puma) common-rail diesel engin...

Fuel Tank Vent Hose - part of the fuel tank ventilation circuit, allowing the tank to breathe and equalise internal pressure as fuel level and temp...

Power Steering Pipe - Pump to Box is the high-pressure hydraulic feed line connecting the power steering pump outlet to the steering box inlet. Th...

Bolt - M10 double hex - securing the swivel pin housing to the front axle case. This dowel bolt locates and fastens the swivel pin housing to the ...

Rear brake disc cross drill & grooved 110 83-06/130 83-06

Ignition and Starter Switch - the electrical switch unit that mounts to the base of the steering column lock, in the ignition and starting circuit,...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

ABS Wheel Speed Sensor - Front for the 4-wheel ABS braking system. Mounted at the front axle, the sensor reads a toothed reluctor ring and generat...

Rocker Arm - Steel - LH for the valve train of the Rover V8 engine, part of the Cylinder Head & Valve Train assembly. This steel rocker arm pi...

Gear Lever Damper for the LT95 four-speed gearbox gear-change mechanism. This damping washer fits at the base of the main gear lever, absorbing vi...

Front Coil Spring - front suspension coil spring, seated between the axle spring pad and the chassis spring turret to support the vehicle and contr...

Bonnet Chequer Plate in black for the Land Rover Defender (2007-2016, Puma). This 3mm aluminium chequer plate fits the restyled Puma-era bonnet an...

Steering Guard - 8mm Alloy - LHD for underbody protection of the steering linkage assembly. Constructed from 8mm laser-cut alloy plate with a tape...

Bonnet Prop Clip for the bonnet support rod assembly on the Land Rover Defender. This clip secures the solid-type bonnet prop rod in its stowed po...

Performance Aluminium Intercooler for the Td5 diesel charge-air cooling circuit. It mounts between the turbocharger outlet and the inlet manifold, ...

Caliper Assembly-Front Brake - LH

Rear Silencer & Tailpipe - the rear section of the exhaust system, combining the rear silencer and tailpipe in a single assembly. It sits at t...

Seat Heater Kit (Retrofit, Pair) adds heating to two seats by fitting flexible heating elements between the seat upholstery and the seat cover, acr...

Locking Nut - a push-on locking nut for securing interior trim and ducting. It pushes onto a stud or screw thread and grips to hold the fixing cap...

Waterpump BGA

Steering Stop Bolt - M12 x 50mm shouldered hex-head bolt for the front axle steering lock assembly. This bolt sets the maximum steering lock angle...

Tailboard Seal for the rear tailgate. Seals the vertical closing edge of the tailboard where it meets the body, keeping out water, dust and draugh...

Rear Crossmember With Extensions for the Defender 90 chassis. The crossmember forms the rearmost structural section of the chassis frame and carrie...

Rear Quarter Panel for the left-hand side, part of the rear body structure. This is the outer body panel that forms the rear side of the vehicle b...

Intercooler Hose - the charge-air hose connecting the turbocharger to the intercooler on the Td5 2.5L 5-cylinder turbo diesel. It carries pressuri...

Brake Pressure Reducing Valve - a control valve in the brake hydraulic circuit. It limits the hydraulic pressure delivered to the rear brakes so t...

Caliper Assembly-Front Brake - RH

Crankshaft Damper for the 300TDi 2.5L turbo diesel engine, mounted on the front nose of the crankshaft. This torsional vibration damper absorbs th...

Self-Tapping Screw, size No. 6 x 3/8", for the door glass and window regulator assembly. This screw secures the window glass run channel to the do...

Cable Tie, a push-fit strap for routing and securing wiring and hoses. The tie strap bundles and secures wiring looms, pipes and hoses, locating i...

Clutch Cover is the pressure plate assembly of the manual transmission clutch, for V8 petrol applications. It bolts to the engine flywheel and cla...

Plastic Washer serves as a spacing and anti-friction washer at the front seat hinge and the rear door check arm pivot. Fitted at the pivot joint, ...

Battery Clamp Bolt - fastener for the battery retention assembly. Secures the battery clamp bar across the top of the battery, holding the battery...

Spring Washer - 6mm for use across gearbox, clutch and general fastening applications. A helical split spring washer for M6 fasteners, providing r...

Fuel Pipe - Pump to Engine for the Td5 diesel fuel delivery system. This under-body pipe assembly carries fuel from the in-tank pump forward to th...

Plain Washer - metric M10 flat washer for use in general fastening assemblies throughout the vehicle. A standard flat washer used to distribute lo...

Tow hitch 110 TD5 adjustable

Pan Head Screw, M4 x 12mm. Metric pan head screw for use across a range of Land Rover assemblies, including brake system and electrical components.

Plain Washer - Large 5/16" is a large plain washer for use with 5/16" fastenings, providing load distribution beneath bolt heads and nuts across La...

Floor-Mounted Headlamp Dipswitch for Land Rover Series 2A vehicles. This foot-operated switch mounts to the cab floor and controls switching betwe...

Steel Wheel - a 5.5J x 16 inch tubeless welded steel road wheel, finished in black. The rim carries a 35 mm offset (ET35). Its welded tubeless con...

Intercooler Hose - To Tube - RH is a charge-air hose in the intercooler (charge-air cooling) circuit of the 2.4L Puma turbo diesel. It forms the r...

EGR Cooler Hose - Engine to Cooler is a coolant hose serving the exhaust gas recirculation (EGR) system. It carries engine coolant from the engine...

O-Ring for the fuel injector harness assembly on the Td5 2.5L 5-Cylinder Turbo Diesel engine. This O-ring provides a seal within the fuel injector...

Locknut is a 1/4" UNF self-locking nut used as a general threaded fastener across the vehicle. Its locking feature resists loosening under vibrati...

Hose Clip is an adjustable worm-drive band clip that clamps a flexible hose onto its spigot or fitting. It tightens over the hose with a screw-dri...

Safari Door - the rear load (tail) door of the body assembly, supplied unglazed and without a spare-wheel carrier. It hinges on the rear body to c...

Crankshaft Pulley Bolt - M12 x 80mm fastener that secures the crankshaft pulley (torsional vibration damper) to the front nose of the crankshaft on...