for Discounts / VAT
for Discounts & Correct VAT
Land Rover Freelander parts for both generations. The L314 (1997 to 2006) and L359 (2006 to 2014) use different platforms, engines, and drivetrains. OEM, Genuine, and aftermarket components in stock. Select your generation below to find correctly fitted parts for your vehicle.
Copper Sealing Washer for banjo bolt connections in the engine oil circuit. This copper washer seats against the machined face of a banjo fitting ...
View full detailsfilter fuel inline Series petrol engines. Used as air filter in vacuum control lines for EGR in: - L322 3.0 M57 DSL (BMW) - Freelander1 M47 16V 2.0...
View full detailsoil filter OEM Hengst Fits: - Defender Puma 2.2L - Defender Puma 2.4L - Discovery Sport 2.2L D 16V - Freelander2 2.2L D 16V - Range Rover Evoque 2...
View full detailsBolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...
View full detailsAir flow meter TD5 OEM VDO /Delphi
Coolant Temperature Sensor threads into the cylinder head and reports engine coolant temperature to the engine management system and the instrument...
View full detailsOil Filler Seal seals the oil filler cap against the filler neck on the camshaft (rocker) cover. It sits between the cap and the cover opening, ke...
View full detailsFlanged Head Screw is an M6 x 12mm machine screw with an integral flange beneath the head. The flange spreads clamping load over a wider area and ...
View full detailsEngine Coolant, pre-mixed for use in the engine cooling system. It circulates through the radiator, water pump and heater circuit to regulate opera...
View full detailsOil Seal - Clutch Housing for the manual transmission drivetrain on the Freelander 1. This oil seal is located at the clutch housing and prevents ...
View full detailsCrankshaft Pulley Bolt & Washer for the 2.2L 16-valve turbo diesel (DW12), securing the crankshaft pulley to the nose of the crankshaft. The b...
View full detailsOil Filler Cap for the engine oil filler neck. Seals the oil filler aperture in the valve cover, preventing oil vapour loss and contamination ingr...
View full detailsInlet Manifold Gasket - Lower for the KV6 2.5L V6 petrol engine, sealing the lower inlet manifold to the cylinder head. The gasket maintains an ai...
View full detailsCylinder Head Bolt Set for the 1.8L K-Series 4-cylinder petrol engine. The set secures the cylinder head to the block, clamping the head gasket to ...
View full detailsFlange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...
View full detailsOil Pressure Switch for the V8 petrol engine. The switch monitors oil pressure in the engine lubrication circuit and activates the instrument clus...
View full detailsFuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...
View full detailsOil Cooler Pipe for the Freelander 1 fitted with the 2.0L L Series (TCIE) Diesel engine. This pipe carries engine oil from the engine to the exter...
View full detailsOil Filter Gasket for the Rover K-Series 1.8L petrol engine, sealing the oil filter housing to the engine block in the lubrication circuit. This g...
View full detailsExhaust Gasket for the flanged joint between the exhaust front pipe and the catalyst section. It seals the bolted flange where the front pipe meet...
View full detailsNut - M10 is an M10 fixing nut for general assembly and repair use across the vehicle. It threads onto an M10 stud or bolt to secure a fastened jo...
View full detailsWasher - a plain flat washer used as a general-purpose fastening component across many assemblies on the vehicle. Fitted under a bolt head or nut,...
View full detailsConnecting Rod Bolt for the engine bottom end, clamping the big-end bearing cap to the connecting rod around the crankshaft journal. Working as a ...
View full detailsFlange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...
View full detailsThermostat Housing Gasket seals the joint between the thermostat housing and the engine, preventing coolant leakage at the housing mating face. Fo...
View full detailsOil Cooler - Heat Exchanger for the Intermediate Reduction Drive (IRD) transfer unit on the Freelander 1. This oil-to-coolant heat exchanger manag...
View full detailsCrankshaft Bearing (main bearing shell) for the BMW M51D25 2.5L 6-cylinder diesel engine. The main bearing shells sit in the bearing saddles of th...
View full detailsIntercooler Hose connecting the intercooler to the inlet manifold. It delivers cooled, compressed charge air from the intercooler to the engine int...
View full detailsCamshaft Position Sensor for the 1.8L 4-cylinder K Series petrol engine, part of the engine management sensor group mounted at the cylinder head. ...
View full detailsOil seal camshaft OEM for : Cylinder Head 2.0L 4 Cyl MPi T Series Petrol and L-series 2.0L 8V Diesel) - Discovery1 2.0 MPi 4 cyl. petrol, - Defen...
View full detailsDrive Belt for the auxiliary drive system of the 2.0L 4-Cylinder 8-valve TCie Rover diesel engine, on air-conditioned applications. Driven from th...
View full detailsCamshaft Oil Seal (front) seals the drive end of the camshaft where it exits the cylinder head, retaining oil within the valvetrain and preventing ...
View full detailsExhaust Downpipe Gasket for the Freelander 1 1.8L K-Series petrol engine (up to VIN YA999999). This gasket seals the flanged joint between the exh...
View full detailsOil Pump Seal for the 1.8L K-series petrol engine. Seals the oil pump body to prevent oil loss at the pump housing interface. Installed at the oil...
View full detailsSump Plug Washer is the sealing washer for the engine oil sump drain plug. It seats between the drain plug and the sump pan to form a leak-tight s...
View full detailsCamshaft Cover Gasket for the Rover KV6 2.5L V6 petrol engine, sealing the camshaft cover to the cylinder head within the valvetrain assembly. It ...
View full detailsValve Collet for the K Series and KV6 petrol engine cylinder heads. The tapered collet locks the valve spring retainer to the valve stem, holding ...
View full detailsHead Gasket - 1.8L - Metal is the cylinder head gasket for the 1.8L Rover K-Series petrol engine used in the Freelander 1. This multi-layer steel ...
View full detailsTiming Belt Tensioner for 1.8L K-Series petrol engines built without automatic belt tensioning. Mounts in the timing belt run and applies the work...
View full detailsTiming Belt for the Freelander 1 1.8L petrol engine. This 143-tooth toothed rubber belt drives the camshaft from the crankshaft, maintaining valve...
View full detailsHill Descent Control Switch - push-push switch mounted in the clutch (bell) housing, forming part of the Hill Descent Control input circuit. The s...
View full detailsCrankshaft Oil Seal (rear) seals the rear of the crankshaft where it leaves the cylinder block into the bellhousing, retaining oil in the crankcase...
View full detailsCoolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...
View full detailsCylinder Head Bolt securing the cylinder head to the cylinder block on the 2.0L 16V Ti-VCT turbocharged petrol engine. The bolt clamps the head, h...
View full detailsCylinder Head Gasket for the 2.0L four-cylinder diesel engine, sealing the joint between the cylinder head and the engine block. It seals the comb...
View full detailsAncillary Drive Belt - engine front-end accessory drive. Multi-ribbed (poly-V) belt driven from the crankshaft pulley to turn the engine-mounted a...
View full detailsCrankshaft Position Sensor for the 2.0L 16V Ti-VCT turbocharged petrol engine (240PS). It mounts in the block adjacent to the crankshaft reluctor r...
View full detailsCrankshaft Position Sensor for the 2.0L 16V Ti-VCT turbocharged petrol engine (240PS). It mounts in the block adjacent to the crankshaft reluctor r...
View full details1997 to 2006. K-series, KV6, L-series, and TD4 (BMW M47R) engines.
Freelander 1 parts →2006 to 2014. eD4, TD4, and SD4 diesel variants plus 3.2 petrol.
Freelander 2 parts →The Land Rover Freelander ran across two distinct generations and was discontinued in 2014. Each generation uses different platforms, engines, and drivetrains. Parts are not interchangeable between them, and fitment must be confirmed by generation, model year, and engine type before ordering.
The Freelander 1 (L314) was produced from 1997 to 2006 in 3-door and 5-door body styles. Engine options included the 1.8-litre Rover K-series petrol, the 2.5-litre KV6 V6 petrol, the early 2.0-litre Rover L-series diesel (1997 to 2000), and the 2.0-litre BMW M47R TD4 diesel (2001 to 2006). It used a monocoque structure with a viscous coupling unit and intermediate reduction drive, with no low-range transfer case. The Freelander 1 sold over 540,000 units across Europe during its nine-year production run, making it the best-selling four-wheel drive vehicle in Europe for five consecutive years after its 1997 launch.
The Freelander 2 (L359) was produced from 2006 to 2014 as a 5-door estate only. It is based on the Ford EUCD platform and shares its architecture with the Volvo XC60. Diesel engines used the 2.2-litre PSA DW12 unit in three states of tune: eD4 (150 hp, front-wheel drive from 2011), TD4 (160 hp), and SD4 (190 hp). Petrol options included the 3.2-litre Volvo B6324S5 inline six and, in later markets, a 2.0-litre Ford EcoBoost petrol. Four-wheel drive models use an active Haldex coupling system. Production ended in October 2014. The Freelander 2 was succeeded by the Discovery Sport.
Vehicle IdentificationIf you are unsure which generation you own, the quickest method is to check the vehicle's production year. Vehicles produced up to and including 2006 are Freelander 1 (L314). Vehicles produced from late 2006 onward are Freelander 2 (L359). The VIN plate is located on the door sill or the engine bay identification plate, depending on market variant, and confirms the build date and chassis designation.
For engine confirmation, the TD4 badge appears on both generations but refers to different engines. On Freelander 1 vehicles produced from 2001, the TD4 is a 2.0-litre BMW M47R unit. On Freelander 2 vehicles, the TD4 is a 2.2-litre PSA DW12 unit. These engines use different parts throughout and must not be confused.
Land Rover's official VIN model year guide can help you confirm your vehicle's model year from its VIN: Land Rover VIN model year guide.
Quality TiersBudget Parts stocks three quality tiers for Freelander components, visible in the collection filter.
Genuine parts are produced by Land Rover or JLR and carry the OEM part number alongside the Land Rover branding. They are the most accurate match to the original specification. Genuine Land Rover parts are listed across both Freelander generations where available.
OEM parts are manufactured by the same original equipment suppliers that produce components for Land Rover's assembly line, but sold without Land Rover branding. These are technically equivalent to Genuine parts for most applications and are the preferred choice for workshops sourcing at trade cost.
Aftermarket parts are produced by independent manufacturers to meet or exceed OEM specification. Quality varies by manufacturer. Budget Parts selects aftermarket lines that meet the functional requirements of the original part and are appropriate for use on Freelander 1 and Freelander 2 vehicles.
For critical drivetrain, braking, and suspension components, OEM or Genuine parts are recommended. Aftermarket parts are well-suited to consumables, service items, trim components, and fasteners.
Trade BuyersThe Freelander is a common vehicle in independent workshops across the Netherlands, Belgium, and Germany. Budget Parts supplies trade buyers and garages across the EU. If you service Freelanders regularly and require volume pricing or VAT-correct invoicing for business purchases, the wholesale portal is available via the header of this site.
Technical GuidesThese articles provide deeper technical context for Freelander owners and workshop technicians. They support diagnosis and part selection and link directly to the relevant generation parts collections.
A technical reference covering driveline, transmission, body, suspension, steering, and software issues across the Freelander 2 (L359) range. Useful for identifying which components are involved before ordering replacement parts.
Freelander 2 faults and fixes guide →A maintenance-focused guide covering the most common wear items on the Freelander 1 (L314), including driveshaft assemblies, engine gaskets, and cooling components. Relevant for owners keeping older L314 vehicles in service.
Freelander 1 maintenance guide →Covers driveline fault diagnosis across multiple Land Rover models including the Freelander 2. Relevant to the VCU and IRD system on Freelander 1 vehicles and the Haldex coupling drivetrain on Freelander 2 models.
Land Rover driveshaft and driveline diagnosis →Driveshafts, propshafts, universal joints, and related driveline components for both Freelander generations.
Driveshaft and propshaft parts →Cooling system components including water pumps, thermostats, and hoses. K-series and TD4 cooling parts are common service items on the L314.
Land Rover cooling parts →Engine components for K-series, KV6, L-series, M47R, DW12, and B6324S5 power units across both Freelander generations.
Land Rover engine parts →Brake discs, pads, callipers, and hydraulic components. Use the collection filter to narrow to your Freelander generation.
Land Rover brake parts →Shock absorbers, springs, bushings, and arms. Freelander 1 and Freelander 2 use different suspension architectures, so confirm generation before ordering.
Land Rover suspension parts →Combined service kits and consumables for routine Freelander maintenance. Listed under service kits when available for your engine variant.
Land Rover service kits →No. The Freelander 1 (L314, 1997 to 2006) and Freelander 2 (L359, 2006 to 2014) use different platforms, engines, drivetrains, and electrical architectures. A Freelander 1 TD4 uses a 2.0-litre BMW M47R engine. A Freelander 2 TD4 uses a 2.2-litre PSA DW12 engine. Parts designed for one generation will not fit the other. Always confirm your generation, model year, and engine type before ordering.
The most reliable check is the production year. Freelander 1 (L314) vehicles were produced from October 1997 to 2006 and were sold in 3-door and 5-door body styles. Note that vehicles produced in late 1997 typically carry a 1998 model year designation. Freelander 2 (L359) vehicles were produced from late 2006 to October 2014 as 5-door estates only. If your vehicle was registered in late 2006 or early 2007, check the build date on the VIN plate, located on the door sill or in the engine bay. The chassis code L314 confirms a Freelander 1. The chassis code L359 confirms a Freelander 2.
Genuine parts carry Land Rover branding and are produced to OEM specification by JLR-approved suppliers. OEM parts are manufactured by the same original equipment suppliers but sold without Land Rover branding, making them a cost-effective equivalent for most applications. Aftermarket parts are produced by independent manufacturers and vary in quality. For braking, drivetrain, and suspension components, OEM or Genuine parts are recommended. For service items, consumables, and trim, quality aftermarket parts are a practical choice.
Yes. Budget Parts is based in The Hague and holds Freelander parts in EU stock. Orders are fulfilled for customers and workshops across the Netherlands, Belgium, Germany, France, and other EU member states. Fitment support and VIN-based part confirmation are available for both Freelander generations.
The Freelander 2 was discontinued in October 2014 and replaced by the Discovery Sport in 2015. The Freelander name was not used on any Land Rover vehicle after that date. A separate Freelander-branded electric vehicle is being developed under a JLR and Chery joint venture for the Chinese market, but this is an entirely different product with no parts commonality with the L314 or L359. Budget Parts supplies parts for the original Freelander 1 (L314) and Freelander 2 (L359) only.