Land Rover Fuel System Parts

Fuel Tank Assembly is the main fuel storage vessel of the fuel system. It holds the fuel supply and feeds it to the fuel pump and delivery lines, ...

Fuel Pipe Double Clip for routing the fuel lines in the fuel delivery system. Retains a pair of fuel pipes along their run, holding them against t...

Injection Pump Gasket seals the fuel injection pump to its mounting face on the timing case of the 200Tdi and 300Tdi 2.5L turbo diesel engines. Th...

Pipe Clip, a routing clip that retains pipework and small-bore lines against the chassis, body or transmission casing. It supports breather, fuel,...

Injector Pipe - the high-pressure fuel line serving the No.4 cylinder on the 2.25L diesel. It carries metered fuel from the injection pump outlet ...

Injector Pipe No.2, a high-pressure delivery pipe in the diesel fuel injection system. The rigid steel pipe carries fuel under high pressure from ...

Fuel Pipe Olive for the fuel supply line. The olive is the compression ferrule that seats between the fuel pipe and its union fitting. When the un...

Spring Washer is an M8 double-coil spring washer used as a fastening component in body and chassis assemblies. The double-coil spring form maintai...

Washer used at multiple points within the manual gearbox assembly, including the main casing, extension housing, oil pump and speedometer drive hou...

Service Kit - 300TDi for Land Rover Discovery 1 and Range Rover Classic with the 300Tdi 2.5L turbodiesel engine. This kit consolidates the key ser...

Bolt M8 X 16 HTSETS 8.8 S/COL sold EACH

Tank Unit Screw is the slotted cheese-head securing screw for the fuel-tank sender unit. It clamps the fuel-level sender flange down onto the top ...

Banjo Bolt (6mm) for the fuel injector leak-off return circuit on the 200TDi and 300TDi 2.5L turbo diesel engines. The hollow bolt clamps the inje...

Accelerator Cable Assembly connects the accelerator pedal to the fuel injection pump throttle lever. It transmits movement of the pedal to the inj...

Injector clamp bolt 2.4 Puma

Carburettor Gasket - a sealing gasket for the Zenith-Stromberg 175CD carburettor as fitted to the 3.5 litre V8. It seals a joint within the carbur...

Fuel Filter Assembly for the Td5 2.5L 5-cylinder turbo diesel fuel system. It filters the diesel supply between the tank and the injection system,...

Suitable for Fitment All diesel models from (VIN) 7A000001 on

Fuel Pressure Regulator mounts on the fuel rail of the multiport electronic fuel injection (EFI) system. It holds a constant pressure difference b...

Electric Fuel Pump mounted externally in the fuel supply system, drawing petrol from the tank and delivering it to the carburettor. This is an ext...

Fuel Filler Tube forming the neck of the fuel tank filler system. It carries fuel from the filler cap opening down into the tank during refuelling...

Fuel Block Connector for the Td5 2.5L 5-cylinder turbo diesel engine, incorporating the fuel pressure regulator at the fuel block. It forms the ju...

Fuel Tank Adaptor Ring secures the in-tank fuel pump and sender unit assembly into the aperture on the top of the fuel tank. The ring locks the pu...

Injector Pipe No.3, a high-pressure delivery pipe in the diesel fuel injection system. The rigid steel pipe carries fuel under high pressure from ...

Injector Pipe No.1, a high-pressure delivery pipe in the diesel fuel injection system. The rigid steel pipe carries fuel under high pressure from ...

Air Intake Grille for the cold air induction system. This adaptor grille sits at the cold air intake, drawing cooler outside air into the intake d...

Sealing Washer for the fuel injector, part of the diesel fuel injection system. The washer seats between the base of the injector and its bore in ...

Injector O-Ring seals the fuel injector within the fuel injection system of the 2.4L Duratorq TDCi (Puma) diesel engine. The seal maintains a pres...

Inline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...

Seal Ring - a copper crush-type sealing washer. It fits beneath a threaded plug or at a metal-to-metal joint and deforms as it is tightened, takin...

Fuel Pipe Union Nut for the fuel delivery line. This female threaded nut draws a fuel pipe up to its mating union, clamping the pipe's flared or c...

Fuel Pump & Sender - in-tank low-pressure fuel pump and fuel level sender assembly for the Td5 2.5L 5-cylinder turbo diesel. The unit mounts v...

Copper Washer is a soft sealing washer used to form a leak-tight metal seal at a threaded or banjo union. Positioned between a bolt or fitting and...

Injector Nozzle is the atomising tip of the diesel fuel injector, sitting in the fuel injection circuit between the injector body and the combustio...

Air cleaner to carburettor hose

Injector sealing washer 2.4 Puma

Carburettor Manifold Gasket - the gasket that seals the inlet and exhaust manifold assembly to the cylinder head face on carburettor-fed engines. ...

Bowl Washer is the sealing joint washer for the fuel sediment bowl (sedimentor) in the fuel system. It seals the bowl to its housing, maintaining ...

Filler pipe hose 90

Fuel Tank Gauge is the fuel level sender unit in the fuel tank assembly. A float-operated sender mounted in the tank, it varies its electrical res...

Tank Mounting Spacer - a spacer used in the fuel tank mounting assembly. It sets the correct standoff between the tank and its supporting bracketr...

Fuel Tank Sender mounts in the fuel tank and signals the fuel level to the dashboard gauge, forming part of the fuel level sensing circuit. A floa...

Past op  1958 - 61:   Sommige S 3 vanaf 1977 en 110 1983 - 84 All 3 Lug Internal Fixings

Fuel Tank Sender Unit for the petrol fuel level sensing circuit. The sender uses a float arm connected to a variable resistor to measure the fuel ...

Banjo Bolt for the fuel and oil circuits, used to secure a banjo union to its housing while allowing fluid to pass through the cross-drilled body. ...

Choke Cable for the carburettor cold-start circuit, connecting the dashboard-mounted choke control to the carburettor choke linkage. When pulled, ...

Water-in-Fuel Sensor for the Td5 2.5L 5-cylinder turbo diesel fuel filter / sedimentor assembly. It threads into the base of the fuel filter housi...

Nut - 10/32" UNF A nut with a #10-32 UNF (Unified National Fine) internal thread, run onto a matching UNF bolt or stud to clamp the joint.