Land Rover Fuel System Parts

Bolt - a hexagonal-head bolt with an M10 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the suspe...

Banjo Bolt is a hollow union bolt used in the fuel system of the 200 Tdi and 300 Tdi engines. It secures a banjo hose fitting at the injection pum...

Carburettor Float Assembly regulates the fuel level in the float chamber of an SU carburettor, governing the fuel available to the metering needle ...

Fuel Spill Pipe for the 200 TDi diesel injection system, part of the injector leak-off (spill return) circuit. The pipe links the injector leak-of...

Filler Hose

Fuel Injector for the EFI V8 petrol engine, part of the multi-point electronic fuel injection system. The injector is an electrically-operated sol...

Accelerator Cable - throttle cable for TDi diesel applications. It connects the accelerator pedal to the injection pump throttle lever, transmitti...

Fuel Tank Cradle - the support cradle that carries the fuel tank beneath the vehicle, bolting to the chassis to hold and locate the tank. Heavy-du...

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Bolt - M8 x 40mm standard metric hex-head fastener for use across engine, gearbox, body, and chassis assembly applications.

Fuel Pipe - Cylinder No.4 for the 200TDi 2.5L four-cylinder turbodiesel, part of the high-pressure fuel injection circuit. This steel injection pi...

Injector Pipe - No.4 is a rigid high-pressure fuel line in the injection circuit of the 2.5L 300 TDi turbo diesel engine. It carries metered fuel ...

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Sedimentor Drain Plug Seal for the sedimentor in the diesel fuel supply. The sedimentor separates water and heavier contaminants from the fuel ahea...

Fuel Temperature Sensor for the EFI V8 petrol engine, part of the electronic fuel injection management system. The sensor measures the temperature...

Accelerator Cable for EFI engines - left-hand drive applications. This cable runs from the accelerator pedal to the throttle body, transmitting pe...

Union Nut for the fuel pipe in the fuel delivery system. This M12 union nut clamps a fuel pipe to its mating union or component port, drawing the ...

Fuel Pump is the in-tank electric fuel pump in the fuel delivery system, mounted within the fuel tank. It draws fuel from the tank and delivers it...

Inline Fuel Filter for carburettor-fed petrol engines, fitted in the low-pressure fuel supply line ahead of the carburettor. It traps rust, scale ...

Fuel Tank Breather Pipe in the fuel tank ventilation system. It vents the fuel tank, relieving pressure and vacuum as the tank fills and empties, ...

Inline Fuel Filter for petrol fuel-injection (EFI) systems, fitted in the pressurised fuel supply line between the fuel pump and the injector rail....

Injector Pipe - number-one cylinder high-pressure injector pipe for the 2.5L 300 TDi turbo diesel. This rigid steel pipe carries diesel at injecti...

Fuel Injector Pipe for the high-pressure injection circuit of the 300 TDi 2.5L diesel engine. This rigid steel pipe carries metered high-pressure ...

Injector Pipe - high-pressure fuel line serving cylinder 3 within the fuel injection system of the 2.5L 300 TDi turbo diesel engine. The pipe carr...

O-Ring sealing the air filter housing to the airflow meter on V8 EFI engines. This O-ring seals the joint between the air filter housing outlet an...

Diesel Fuel Filter Plug Seal - a sealing ring for the drain plug on the diesel fuel filter and sedimentor. It seals the drain/bleed plug against t...

Hex Nut - 7/16 UNF fixing nut. Used on the fuel pipe unions of the 3.5L V8 twin-carburettor petrol engine. Also supplied as part of a service kit.

Sedimentor O-Ring for the diesel fuel filter assembly. This rubber sealing ring seals the sedimentor bowl against the filter head, preventing fuel...

Flanged Nut - M6 flanged hex nut for use across a wide range of Land Rover assemblies including engine, drivetrain, body, braking, and electrical a...

Flexible Rubber Mounting Bush for the Land Rover Discovery 1 and Range Rover Classic. This rubber isolator bush is used in various under-bonnet mo...

Intake Elbow Seal for the 3.5L V8 twin-carburettor petrol engine. The seal sits between the air cleaner intake elbow and the carburettor intake to ...

Injector Pipe Kit - set of 4 high-pressure fuel pipes for the 300Tdi 4-cylinder turbo diesel engine, mechanical injection pump variant (Less EDC). ...

Sedimentor Drain Plug with Seal for the diesel fuel filter assembly. Fitted at the base of the sedimentor bowl, this plug allows the bowl to be dr...

Kit gasket carb for Rover V8 engines fitted with SU carburetors

Injector Pipe for the No.4 cylinder of the 2.5L 200TDi diesel engine. This rigid high-pressure steel pipe carries metered fuel from the injection p...

Injector Pipe for the 200TDi 2.5L 4-Cylinder Turbo Diesel engine, part of the High-Pressure Fuel Delivery Circuit. This high-pressure steel pipe r...

Injector Pipe for the 200TDi 2.5L 4-Cylinder Turbo Diesel engine, part of the High-Pressure Fuel Delivery Circuit. This high-pressure steel pipe r...

Injector Pipe for the 200TDi 2.5L 4-Cylinder Turbo Diesel engine, part of the High-Pressure Fuel Delivery Circuit. This high-pressure steel pipe r...

Injector O-Ring - a sealing ring for the fuel injectors in the electronic fuel injection system. It seals the injector where it locates in its bore...

Fuel Injector within the multi-point injection (MPi) fuel delivery system of the 2.0L T-Series 4-cylinder petrol engine. The injector receives a t...

Injector Clip for V8 EFI fuel injection systems, used in the fuel delivery assembly at the intake manifold. This retaining clip secures the fuel i...

Fuel Injector delivers atomised diesel into the combustion chamber of the 2.5L 300TDi engine. Fitted to non-EGR applications.

Injector Clamp Stud - 200Tdi / 300Tdi is the threaded stud used to secure the injector hold-down clamp in the cylinder head of the 200Tdi and 300Td...

Accelerator Cable for the throttle control linkage, connecting the accelerator pedal to the engine's throttle mechanism. The cable transmits pedal...

Fuel Sedimentor is a water and sediment trap in the diesel fuel supply line, installed upstream of the fuel filter and injection pump. Fuel passes...

Fuel Feed Hose for the fuel supply circuit. This flexible hose carries fuel within the fuel delivery or evaporative emission system. On diesel app...

Fuel Filter Assembly within the diesel fuel supply circuit, removing contaminants from the fuel before it reaches the injection system. Installed ...