Land Rover Hardware & Fasteners

Flywheel Bolt, 7/16" UNC x 1" hexagonal head, securing the flywheel to the rear crankshaft flange. Used on V8 petrol engines with manual transmiss...

Clip is a retaining clip in the front windscreen wiper linkage. It secures the wiper motor and linkage assembly, holding the linkage components to...

Locking Washer of the Starlock (shakeproof) type, a push-on retainer used to hold a component onto a plain shaft or to lock a fastener against vibr...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Lock Washer secures the retaining hardware on the layshaft (countershaft) within the manual gearbox. A tab on the washer is folded against the ret...

Saddle Clip for routing and securing the power steering pipes. This saddle-shaped clip clamps the power steering hydraulic pipes to the chassis or...

Carpet Drive Fastener is a trim fastener used within the interior floor carpet assembly to secure the carpet to the floor. The fastener is driven ...

Bolt for the adjustable rear suspension arm on the Freelander 2 and Range Rover Evoque. This M14 × 85mm special bolt secures the adjustable rear a...

Self-Tapping Screw - an exterior body trim fastener. It secures the protective rubbing strip (side moulding) to the rear quarter panel, cutting it...

Circlip - LT77 Selector Shaft for the LT77 5-speed manual gearbox. This circlip retains the selector shaft within the gear selector and shaft asse...

Pedal Clutch Bearing

Circlip for the handbrake (parking brake) linkage. This external retaining circlip secures the handbrake relay elbow onto its pivot post, holding t...

Toebox Trim Fastener - the fixing that secures the footrest and toebox trim panel in the footwell. It retains the lower trim at the A-post and toe...

Bolt - M6 x 30mm is a metric threaded fastener with a 6 mm nominal thread diameter and a 30 mm shank length. It secures bolted joints where an M6 ...

G-Hook - a hook fitting for the soft top drain channel. It anchors and tensions the drain channel that runs along the soft top, holding the channe...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Fuel Tank Mounting Washer is used at the fuel tank mounting points, spreading the clamping load of the fixing across the mounting bracket or strap....

Grille Spring Clip for securing the front grille panel on Series III models. Fitted at the grille mounting points, this spring clip retains the fro...

Grommet / Blanking Plug - Dash Bulkhead for Land Rover Defender. This rubber plug seals an unused aperture in the dash bulkhead (such as a heater ...

Core Plug - Cylinder Head A 7/8" diameter core plug (welch/expansion plug) that seals a casting core hole in the cylinder head. It closes the open...

Plain Washer is a flat fastening washer fitted under a bolt head or nut to spread the clamping load across a wider area and protect the mating surf...

Screw – a black self-tapping screw with a pan head and Pozidriv drive recess, size No. 10 × 5/8 in, used to secure body, trim and panel fixings. B...

Washer - a general-purpose fixing washer used across multiple body, brake and chassis assemblies. It spreads the clamping load of a bolt or nut ov...

Cable Tie for securing wiring looms and cables in Land Rover applications.

Bolt securing the fuel injector and high-pressure fuel pipe assembly on the engine fuel system. It clamps the injector and high-pressure pipe unio...

A/C O-Ring - a sealing O-ring for the air conditioning refrigerant hose connections. It seats at the couplings between refrigerant hoses and compo...

Brake Pipe Clip - Rear secures the rear brake pipes on the Discovery 2, holding the hydraulic lines in place along the chassis. The clip prevents ...

Rocker Shaft Locating Bolt for the 2.25L and 2.5L petrol, 2.5L naturally aspirated diesel and 2.5L turbo diesel engines, securing the rocker shaft ...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Set Screw - a fully threaded hexagonal-head setscrew with an M10 metric thread and a 20 mm length. A general-purpose fixing used at fastening point...

Fuel Injector Bolt - retaining bolt securing the fuel injector clamp to the cylinder head on the 2.4L Duratorq TDCi (Puma) common-rail diesel engin...

Mainshaft Nut - castellated nut that retains the assembled components on the rear of the gearbox mainshaft. The castellations accept a split pin to...

Splash Seal

Propshaft Lock Washer, used within the propshaft and viscous coupling assembly. The lock washer is seated beneath the retaining fastener at the pr...

Double Clip for routing and securing battery cables. This twin clip retains two leads together, holding the cabling in place along its run.

Clevis Pin for the differential lock selector linkage in the LT230 transfer gearbox. This clevis pin secures the selector lever pivot that actuate...

Gearchange Roll Pin - a tension (roll) pin used in the manual gearchange mechanism to secure the gear lever to the selector shaft. Applies to the ...

Fastener - black plastic drive-type (fir tree) push-in fastener used throughout the vehicle to secure body trim panels, interior linings, underbonn...

Rivet is a body fixing used to secure sheet-metal panels, wheelarch liners and trim to the vehicle structure. It forms a permanent, vibration-resi...

Fusebox Cover Clip - a female retaining clip in the facia trim assembly. It secures the fusebox cover panel to the dashboard, locating onto the cor...

Tow Hook Protective Cap is a cover for the towing eye aperture in the bumper. It closes off the tow hook mounting point when not in use, keeping o...

Torx Screw - 4.8 × 25mm for use in Land Rover body and trim assemblies. A metric Torx-head screw, 4.8mm diameter × 25mm length, for use where Torx...

Clevis pin

Plate

Bolt - M12 × 160 mm hex-head bolt used as a chassis and suspension fixing. It secures suspension radius arms and links, the top link fulcrum and ba...

Core Plug - Cylinder Block Expansion Port is a pressed-steel sealing plug installed in the outer face of the cylinder block to close the casting ap...

Exhaust Manifold Bolt for the Rover V8 petrol engine, threaded 3/8" UNC and 1 1/8" long. The bolt secures the exhaust manifold to the cylinder hea...