for Discounts / VAT
for Discounts & Correct VAT
Parts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible. Covers pre-facelift and post-facelift specifications. Stock is held in the Netherlands and dispatched across the EU. Use the filters to narrow by model year, category, or quality grade.
Lamp - Side Flasher
Thermostat and Housing assembly for the 2.0L 16V TIVCT turbocharged petrol (GTDi) engine. The thermostat regulates coolant flow to bring the engine...
View full detailsWasher Bottle Filler Cap - the filler cap for the windscreen washer fluid reservoir. It closes the reservoir filler neck, sealing the washer fluid...
View full detailsFront Brake Pad Set - friction pads for the front disc brake assembly. The pads locate in the front caliper and are clamped against the brake disc...
View full detailsFuel Filter for petrol applications, mounted in the rear fuel line assembly alongside the carbon canister and evaporative leak-detection components...
View full detailsTiming Chain - Secondary, Upper is part of the camshaft drive of the 2.0L Ingenium four-cylinder turbo diesel (AJ200D / AJ20D4). It runs in the up...
View full detailsFuel Filter - diesel fuel filter for the 2.2L Td4 engine, fitted in the low-pressure fuel supply circuit. The filter sits between the fuel tank an...
View full detailsEngine Mount Insulator is the rear lower engine mounting within the engine support system. It locates the engine to the subframe and isolates engi...
View full detailsDrain Plug Washer - a sealing washer for the differential drain and filler plugs on the front and rear axles. It seals the plug against the axle c...
View full detailsFront suspension bump stop - part of the front strut and coil spring assembly. The moulded rubber bump stop is fitted over the strut piston rod, b...
View full detailsRear Brake Disc, solid type, 302mm diameter, forming part of the rear axle braking assembly. The disc provides the friction surface for the rear b...
View full detailsFuel Pump Gasket - the cover gasket for the diesel fuel injection pump. Seals the injection pump cover joint on the 2.2L diesel engine, maintainin...
View full detailsCoolant Hose Assembly - heater outlet to thermostat housing hose in the engine cooling circuit. Returns coolant from the heater matrix outlet to t...
View full detailsFuel Pressure and Temperature Sensor for petrol fuel-injection systems. The combined sensor measures fuel rail pressure and fuel temperature and r...
View full detailsTiming Chain for the timing drive of the 2.0L Ingenium four-cylinder diesel engine (AJ200D / AJ20D4). This is the lower, primary chain of the two-...
View full detailsCoolant Inlet Connector - the coolant inlet connection at the cylinder head on the 2.2L DW12 diesel engine. It forms the sealed joint between the ...
View full detailsBumper Retainer Nut - a push-in retaining nut used in the front bumper, radiator grille and rear bumper assemblies. The retainer clips into a pres...
View full detailsFront spring pad for the front suspension strut and coil spring assembly. The pad is an elastomer insulator that seats between the end of the coil...
View full detailsBolt for the exhaust system front section. This fastener secures the flanged joint between the exhaust manifold and the front pipe section, holdin...
View full detailsAnti-Roll Bar Bush for the suspension stabiliser system. This rubber insulator clamps the anti-roll bar to its mounting, locating the bar while all...
View full detailsOil Separator is the crankcase ventilation (PCV) oil separator for the 2.0L 16V turbocharged petrol engine. It sits in the crankcase breather circ...
View full detailsOil Filter - engine oil filter element for the 2.2L Td4 diesel engine, supplied with its sealing ring. The element fits inside the filter housing ...
View full detailsHex Head Bolt - threaded fastener used at the engine mountings and at the front suspension strut mounting. Driven with a standard spanner or socke...
View full detailsFront Brake Disc - 300 mm vented, supplied singly; two are required to do the front axle. The vented construction carries internal vanes between t...
View full detailsThermostat Housing - coolant outlet housing in the engine cooling circuit of the 2.2L Td4 diesel engine. The housing mounts to the engine and carr...
View full detailsThermostat Housing for the 2.0L Ingenium petrol engine (AJ200P, including PHEV applications). The housing holds the coolant thermostat and forms p...
View full detailsOil Cooler Return Connector is a connector fitting in the engine oil cooler circuit of the 2.2L diesel engine (DW12). It joins the oil cooler retu...
View full detailsOutput Shaft Oil Seal seals the transmission output shaft where it exits the case on the ZF 9HP48 / 9HP50 nine-speed automatic gearbox (all-wheel-d...
View full detailsGrommet - a moulded rubber grommet fitted into an aperture in the body. It lines and seals the opening, providing a finished edge and helping to k...
View full detailsRadiator Cap - screw-on pressure cap for the coolant expansion tank in the engine cooling system. The cap seals the expansion tank and holds the c...
View full detailsOil Filter Housing Cover for the oil cooler and filter housing on the 2.2L DW12 turbo-diesel engine. The cover closes the oil filter housing, reta...
View full detailsIgnition Coil for the engine ignition system. It steps up battery voltage to the high voltage needed to fire the spark plug and is mounted directly...
View full detailsCoolant Expansion Tank is the reservoir within the engine cooling system. It accommodates coolant expansion as temperature rises, provides a fill ...
View full detailsRear Brake Pad Set - friction pads for the rear disc brake assembly, supplied as a rear axle set complete with springs. The pads locate in the rea...
View full detailsTransmission Oil Pipe Kit - the external oil pipework for the 9-speed automatic transmission (9HP48). The pipes route transmission fluid between t...
View full detailsLower Engine Mount (engine support insulator) securing the engine at its lower mounting point. It carries the lower engine load and damps engine v...
View full detailsEngine Start/Stop Switch - the push-button ignition switch of the keyless start system. Pressing the button powers up and starts or stops the engi...
View full detailsSeal - Door Front and Rear
Cigar Lighter Base - the socket housing for the cigar lighter and 12V auxiliary power point. It mounts in the instrument panel or floor console and...
View full detailsFuel Tank Vent Reservoir for the evaporative emission control (EVAP) system on petrol models. It collects and stores fuel vapour drawn from the fue...
View full detailsAxle Case Seal - Front seals the front axle case (final drive housing) around the driveshaft where it passes through the case. It retains the diff...
View full detailsDriveshaft Retainer Circlip locks the inner end of the front driveshaft into the differential inside the front axle case. The clip springs into a ...
View full detailsDriveshaft Oil Seal - Inner - Front LH is fitted to the front axle case (final drive housing) and seals around the inner end of the left-hand front...
View full detailsDriveshaft Oil Seal - Inner - Front RH is fitted to the front axle case (final drive housing) and seals around the inner end of the right-hand fron...
View full detailsOil Seal - Differential Flange - Front seals the front differential where the drive flange exits the axle case. It runs against the differential o...
View full detailsCylinder Head Gasket for the 2.0L 16V TiVCT turbocharged petrol engine, sealing the joint between the cylinder head and the engine block. It conta...
View full detailsTransmission Oil - Hypoid is a hypoid gear oil for the Power Transfer Unit (PTU) / transfer box. It lubricates the hypoid gearset that sends drive...
View full detailsOil Level Plug is the threaded oil level indicator plug for the 6-speed AWF21 automatic gearbox. Removed to check and set the transmission fluid l...
View full detailsParts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible, this collection covers pre-facelift and post-facelift specifications. If you own the 2019-onward Evoque, see the L551 parts collection.
The Range Rover Evoque L538 is the first-generation Evoque, produced at Halewood, UK from July 2011 to 2019 under chassis code L538. Model years run from 2012 to 2019. The collection covers the 5-door and 3-door SUV variants (produced through to 2018) and the convertible (produced from 2016 to 2019).
The L538 rides on the D8 platform, also known as LR-MS, a high-strength steel monocoque architecture developed by Land Rover as a heavily modified derivative of the Ford EUCD base. The D8 platform is also used on the Land Rover Discovery Sport. This architecture gives the Evoque a car-like driving character distinct from the body-on-frame and aluminium-intensive platforms used in other Range Rover generations.
Drivetrain configuration varies by variant. Four-wheel drive vehicles use a Haldex-based on-demand AWD system. Front-wheel drive was available on select diesel variants, specifically the eD4, which used a single-clutch, front-axle-only setup for improved efficiency. Confirming your drivetrain before ordering driveline, coupling, or differential components is essential. Generation-specific Haldex AWD service information is published by Haldex.
This collection does not cover the Range Rover Evoque L551 (2019 onward). If your vehicle was registered from 2019 onward, use the L551 parts collection linked in the intro above this product grid.
The L538 production run splits into two distinct specifications at the 2015 model year.
Pre-facelift vehicles (model years 2012 to 2015) used Ford-derived powerplants. Petrol variants used the 2.0L Ford EcoBoost Si4 turbo four-cylinder. Diesel variants used the 2.2L Ford Duratorq (PSA DW12) in TD4 and SD4 states of tune. The automatic gearbox on pre-facelift vehicles is the 6-speed Ford Aisin AW F-21 unit, also designated the Aisin Warner TF-81SC.
Post-facelift vehicles (model years 2016 to 2019) introduced JLR's Ingenium engine family. Both petrol and diesel variants moved to the 2.0L Ingenium turbo four-cylinder. The 9-speed ZF 9HP automatic gearbox replaced the 6-speed unit on automatic variants. The 6-speed Getrag M66EH50 manual remained available in select markets on diesel variants throughout the production run.
Engine-specific parts including oil filters, timing components, gaskets, sensors, and turbo components are not interchangeable between the Ford-derived and Ingenium specifications. Always confirm your engine code and model year before ordering.
Reference note: ZF 9HP transmission technical information is published by ZF Group.
Fitment GuidanceThe most reliable method for confirming parts fitment on an L538 is your Vehicle Identification Number (VIN). The VIN is a 17-character code stamped on the door jamb plate, on the windscreen base near the A-pillar (driver or passenger side depending on market variant), and recorded in your V5C or national registration document.
The tenth character of the VIN encodes the model year. The eighth character encodes the engine variant. If you are ordering engine-specific parts, turbo components, gearbox parts, or any item that changed at the 2015 facelift, cross-referencing your VIN with the part number is strongly recommended before purchase.
If you are unsure which specification your vehicle is, contact the Budget Parts team directly. Trade account holders can request fitment confirmation through the wholesale portal.
Catalogue ScopeThis collection includes suspension parts such as control arms, bushings, drop links, anti-roll bars, shock absorbers, and wheel bearings. Brake parts include pads, discs, calipers, brake pipes, and brake hardware. Engine parts cover oil filters, sump washers, hydraulic tappets, expansion tank caps, and ancillary components. Drivetrain parts include propshaft bolts, driveshaft components, and wheel nuts. The collection also includes electrical parts such as relays and sensors, service and maintenance items including ATF fluids and service hardware, body and chassis fixings, and workshop supplies including brake cleaner and fastener assortments.
Use the category filter above to narrow results to your area of work. The quality filter allows you to select between Genuine Land Rover, OEM, and Aftermarket grades.
Quality TiersEvery part in this collection is marked with one of three quality grades.
Genuine Land Rover parts are sourced through the official Jaguar Land Rover distribution channel. They carry the original Land Rover part number and packaging. These are the appropriate choice when OEM provenance documentation is required, such as for warranty or insurance purposes.
OEM parts are produced by the same manufacturers that supply Land Rover directly, sold outside the official JLR channel. The component is frequently identical to the Genuine part. OEM is the standard choice for independent workshops and experienced owners who want original-specification quality without the official channel markup.
Aftermarket parts are independently manufactured. Quality varies by supplier and application. Each listing specifies the grade, and the product description notes any relevant fitment or application limitations. Aftermarket is appropriate for non-critical components or where cost is the primary constraint.
TradeBudget Parts operates a wholesale portal for registered independent workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. If you manage a workshop or operate as a parts buyer, visit the wholesale login page to access trade terms or register your account.
Generation ReferenceThe L538 is the first-generation Evoque. The second-generation Evoque, the L551, entered production in 2019 on the PTA platform with 48V mild-hybrid technology and Ingenium engines throughout. Parts are not interchangeable between generations.
For the full Range Rover model family and generation reference, see the Range Rover parts collection.
Technical GuidesThe articles below provide diagnostic and technical context relevant to Range Rover Evoque L538 owners and workshops. They support, but do not duplicate, the parts categories in this collection.
Technical guide to the L538 covering the Ford-to-Ingenium engine split, Haldex service requirements, and the suspension and platform architecture that defined the first-generation Evoque.
Range Rover Evoque L538 guide →Owner and workshop guide to the Evoque convertible covering the structural changes for the open-roof configuration, the electric roof system, AWD configuration, and common faults relevant to parts selection.
Range Rover Evoque convertible guide →The Freelander 2 shares Haldex AWD architecture and overlapping engine families with the Evoque L538. This guide covers Haldex service intervals, coupling failure patterns, and rear differential diagnosis that applies directly to L538 AWD variants.
Freelander 2 faults and Haldex service guide →The Range Rover Evoque L538 was produced from July 2011 to 2019. Model years run from 2012 to 2019. The 5-door and 3-door SUV variants were produced through to 2018. The convertible variant was introduced in 2016 and produced through to 2019. Parts availability in this collection covers the full L538 production window across all body styles.
If your vehicle was registered before 2019, it is almost certainly the L538 first generation. If registered from 2019 onward, it is the L551 second generation. The clearest confirmation is your VIN. The tenth character of your 17-character VIN encodes the model year. You can also check the driver's door jamb plate, which will show the build date and in some markets the chassis code. If you are unsure, contact Budget Parts directly before ordering.
The L538 was significantly updated at the 2015 model year. Pre-facelift vehicles use Ford-derived engines (2.0L EcoBoost petrol, 2.2L Duratorq diesel) and a 6-speed Aisin automatic gearbox. Post-facelift vehicles use JLR Ingenium engines (2.0L petrol and diesel) and a 9-speed ZF 9HP automatic. Engine-specific parts including oil filters, timing components, turbo components, and gaskets are not interchangeable between these specifications. Always confirm your model year and engine code before ordering.
Four-wheel drive variants of the L538 use an on-demand Haldex AWD system. This couples the rear axle electronically and distributes torque when front-axle slip is detected. Some diesel variants were available in front-wheel drive only, specifically the eD4, which does not use a rear differential or Haldex coupling at all. Confirming your drivetrain configuration before ordering rear axle, coupling, or propshaft components is important. If you are unsure, check your V5C or contact Budget Parts.
The L538 used two engine families across its production run. Pre-facelift vehicles (2012 to 2015 model year) used the 2.0L Ford EcoBoost Si4 turbo petrol and the 2.2L Ford Duratorq (PSA DW12) diesel in TD4 and SD4 outputs. Post-facelift vehicles (2016 to 2019 model year) used JLR's 2.0L Ingenium turbo four-cylinder in both petrol and diesel forms. Parts that are engine-specific are listed with applicable engine codes in the product descriptions.
The L538 uses the D8 platform, also known as the LR-MS. This is a high-strength steel monocoque architecture developed by Land Rover as a substantially redesigned derivative of the Ford EUCD base. The same platform underpins the Land Rover Discovery Sport. It is a different architecture to the aluminium-intensive platforms used on the Range Rover L405 and Range Rover Sport L494.
Yes. Budget Parts operates a wholesale portal for registered workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. You can register or log in through the wholesale portal link in the site header. For volume orders or specific part enquiries, contact the Budget Parts team directly.
Updated: 13 May 2026