Range Rover Sport L320 Parts

Valve Cover Screw and Sleeve from the cylinder head cover fixings of the petrol V8 and supercharged V6 engines. The screw secures the camshaft (va...

Oil Level Sensor - electronic engine oil level sensor mounted in the wall of the sump, forming part of the engine lubrication monitoring circuit. ...

Screw, M6 x 38mm, from the timing gear assembly - timing chains, tensioners and guides, and the auxiliary drive. It retains the chain guide in pos...

Oil Separator Reservoir for the 3.0L V6 diesel, part of the crankcase ventilation circuit within the engine emission control system. Crankcase blo...

Crankcase Ventilation Tube for the 3.0L V6 turbo diesel engine, part of the oil pan and crankcase breather arrangement. Combustion gases that leak...

Lower chain guide for the auxiliary drive chain, part of the timing gear assembly on the 5.0L V8 petrol engine (AJ133). The guide runs against the...

Inlet Valve - cylinder head inlet (induction) valve for the 5.0L V8 AJ133 supercharged petrol engine. The inlet valve admits the intake charge int...

Thermostat Housing for the 5.0-litre AJ133 V8 petrol engine, part of the engine cooling circuit. The housing seats the coolant thermostat and form...

Vacuum Hose running from the inlet manifold to the symposer on supercharged petrol engines. The symposer is an intake resonator that channels indu...

Inlet Manifold Gasket for the left-hand cylinder bank of the 5.0 litre V8 petrol engine (AJ133). It seals the joint between the inlet manifold and ...

O-ring for the engine oil cooler and oil filter housing assembly, sealing the top oil cooler hose connection on the 3.0L V6 diesel. It seals the j...

Oil cooler seal, 18 mm diameter, sealing an oil transfer connection between the engine and the oil filter housing on the 3.0L V6 diesel. Three are...

Automatic Transmission Fluid (ATF) for the automatic gearbox and power steering circuit. Specified as the transmission and power steering fluid to...

Valve Cover Stud and Sleeve from the cylinder head cover fixings of the petrol V8 and supercharged V6 engines. The stud threads into the cylinder ...

O-Ring for the engine cooling system - it seals the water outlet tube at its connection to the cylinder block, alongside the thermostat housing. T...

Timing Gear Bolt - Lower is the M16 x 70mm flanged hex bolt that retains the lower timing gear on the crankshaft. It is also listed as the cranksha...

Camshaft Cover Gasket - LH seals the left-hand camshaft cover to the cylinder head on the AJ133 5.0L V8 petrol engine. It closes the joint around ...

Valve Spring Retainer from the cylinder head valve train, the top cap that closes off the valve spring. It sits on top of the valve spring and is ...

Oil cooler seal, 9.5 mm diameter, sealing the small-bore oil transfer connection between the engine and the oil filter housing on the 3.0L V6 diese...

Tube - Drain

Cylinder Head Bolt secures the cylinder head to the engine block on V6 and V8 petrol engines. Threaded M11 x 178 mm. Twenty bolts are required per...

Timing Chain Tensioner Blade is the tensioner blade in the engine's timing chain drive. It provides the curved, low-friction face that the timing c...

Exhaust Manifold Gasket seals the exhaust manifold to the turbocharger on the 3.0L V6 diesel engine. Fitted at the manifold-to-turbocharger flange...

Collet - Anti-Roll Bar Pipe - retaining collet used in the pipe connections of the Active Cornering Enhancement (ACE) anti-roll bar system. The co...

O-Ring sealing the thermostat housing in the engine cooling circuit. Seats between the thermostat housing and its mating face to seal the coolant ...

Turbocharger Oil Return Tube Gasket seals the oil return (drain) tube where it meets the turbocharger, within the turbocharger lubrication circuit....

Crankshaft Seal and Retainer - the rear crankshaft oil seal complete with its retainer housing, sealing the rear of the crankshaft where it exits t...

EGR Gasket Inlet

Axle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...

Camshaft Screw for the cylinder head and camshaft assembly of the 3.0-litre TDV6 diesel engine. This is a manufacturer-specification retaining scr...

Thermostat Housing Gasket seals the joint between the thermostat housing (water outlet) and the cylinder head within the cooling system. It mainta...

Breather Tube forming part of the crankcase ventilation circuit on the 5.0L V8 petrol engine (AJ133). It carries crankcase blow-by gases from the ...

Retaining Clip is a fastening clip used in the radiator grille and front bumper assembly. It secures the grille and front bumper trim components t...

Clip - retaining clip for the radiator grille and front bumper assembly. It secures the grille and bumper components to their mountings.

Exhaust downpipe gasket sealing the flanged joint between the front exhaust pipe (downpipe) and the catalytic converter, in the front section of th...

Exhaust downpipe gasket sealing the flanged joint between the front exhaust pipe (downpipe) and the catalytic converter, in the front section of th...

Spark Plug Aperture Gasket seals the spark plug aperture in the cylinder head cover on the left hand cylinder bank. It closes the joint between th...

Chain - Timing

O-Ring seals the variable valve timing (VVT) solenoid within the timing gear and sprocket assembly. It maintains an oil-tight joint between the VV...

Turbo Oil Return Hose Gasket seals the upper joint of the turbocharger oil return hose, where the hose meets the turbocharger housing in the engine...

Inlet Manifold Gasket - 5.0 V8 - RH seals the inlet manifold to the cylinder head on the right-hand bank of the 5.0 litre V8 petrol (AJ133) engine,...

Spark Plug Aperture Gasket for the right-hand camshaft cover, sealing the spark plug well against oil ingress. The camshaft cover carries a tube f...

Gasket - Oil Filter to Block seals the joint between the oil filter housing and the cylinder block, within the Oil Cooler and Filter assembly. It ...