Products

Synchroniser Assembly for 3rd and 4th gear, mounted on the mainshaft of the R380 five-speed manual gearbox. The assembly locks the selected gear t...

Synchroniser Assembly for 5th gear, mounted on the mainshaft of the R380 five-speed manual gearbox. The sliding sleeve is moved by the fifth-gear ...

DIFFERENTIAL - ASSEMBLY - FRONT AXLE - 24 SPLINE - 4 BOLT FLANGE - D2

Clutch Slave Cylinder Push Rod within the Clutch Actuation Assembly, transmitting hydraulic force from the external slave cylinder to the clutch re...

Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...

Clutch Slave Cylinder for the hydraulic clutch release system on Defender and Discovery 2 models fitted with the R380 manual gearbox. Mounted on t...

Release Bearing Guide - the guide sleeve in the clutch release mechanism, mounted on the front cover of the manual gearbox. It encircles the gearb...

Stub Axle Washer for the front and rear hub and wheel bearing assembly. The washer locates over the stub axle and seats between the outer wheel bea...

Differential Pinion Oil Seal with a double sealing lip, for the front and rear differentials. It is press-fitted into the differential housing aro...

Stub axle oil seal inner

Thrust Washer - mainshaft thrust washer for the R380 five-speed manual gearbox. Located at the mainshaft 5th/reverse gears, it controls end-float ...

Gearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...

Differential Case - the rotating carrier at the centre of the front axle differential assembly. The crown wheel bolts to the case, and the case in...

Hub Cap closes the centre of the front hub drive flange, covering the driveshaft coupling bolts within the front axle hub assembly. This is the pl...

Swivel Pin Housing Thrust Washer for the front axle swivel pin assembly. Installed within the swivel pin housing between the pin head and the hous...

Swivel Pin Housing Oil Seal for the front axle swivel and stub axle assembly. This is the outer seal, fitted at the interface between the stub axle...

Needle Roller Bearing for the front axle swivel pin housing. The bearing seats in the swivel housing bore and carries the stub axle, providing rad...

Intercooler - the charge-air cooler in the induction system of the 300Tdi 2.5L four-cylinder turbo diesel engine. Mounted in the airflow at the fr...

Rear end door latch assembly with CDL

Driver's door lock actuator and switch CDL

Door Lock Actuator and Switch for the central door locking (CDL) system, operating within the door latch mechanism. The actuator drives the latch ...

Rear Door Finisher for the internal rear door release assembly. This trim panel finisher fits around the interior door release mechanism on the re...

Centre Console Switch Pack moulding in black, forming part of the centre console trim. This panel mounts in the centre console and provides the ap...

Cubby Box Cup Holder for the centre console cubby box. The holder mounts to the sloping front face of the cubby box, providing a fixed location fo...

Flanged Locking Nut, M10. General-purpose threaded fastener. The integral flange spreads the clamp load over a wider bearing area, removing the ne...

Nyloc Flanged Nut - M8 flanged nut with a nylon insert, used on front suspension fixings. The nylon collar deforms around the bolt thread as the n...

Hex Nut - M12 - a standard M12 hexagonal nut used as a general-purpose fastener across the vehicle. The six-sided form is tightened with a standar...

Front Door Hinge Kit - Body Side for the front door mounting assembly. This kit provides the body-side hinge components required to secure the fro...

Front door hinge fixing kit used within the body door hinge mounting assembly. The kit provides the required fasteners and mounting components to...

Light Kit is a complete exterior lamp set of 73 mm round lamps covering the front side, indicator, side repeater and rear stop/tail positions in on...

Roof Access Ladder in a hot-dip galvanised steel finish, providing safe access to a roof rack. This is a non-drill (bolt-on) type ladder that moun...

Viscous Fan Coupling Spanner Set, a pair of thin-section spanners (32 mm and 36 mm) for removing and refitting the viscous fan coupling at the wate...

Oil Filter Wrench - a removal tool for the spin-on oil filter on the Td5 2.5L diesel engine. The wrench locates over the end of the filter caniste...

Hub Nut Socket is a 52mm deep impact socket with a 1/2" square drive, used to remove and refit the hub retaining nut on the wheel bearing assembly....

Propshaft bolt kit Defender D1 RRC

Ball Joint Service Tool for the steering drop-arm ball joint. The tool presses the drop-arm ball joint (part RBG000010) into and out of the drop a...

Fulcrum Bracket and Ball Joint Assembly for the rear A-frame (top link). The bracket forms the apex of the A-frame and bolts to the rear axle; the ...

A-frame Ball Joint Fitting Kit – the mounting hardware for the rear A-frame ball joint and its housing. The fixings secure the ball-joint housing t...

Adjustable Panhard Rod - lateral axle location link, supplied with polyurethane bushes. The panhard rod locates the axle laterally relative to the...

Front Door Hinge Set - Aluminium - replacement hinges forming the pivot between the front row doors and the A-post. The original hinge castings co...

Door Hinge Pin Kit - Stainless Steel - renewal hardware for the door hinge pivots. The hinge pin is the wearing part of a door hinge: as the pin a...

Stainless Steel Bolt Kit for securing the front door hinges to the body on the 2-door Defender. The fasteners replace the original mild-steel fixin...

Stainless Steel Bolt Kit for securing the front door hinges to the body on the 2-door Defender. The fasteners replace the original mild-steel fixin...

Door Bolt Kit - a stainless steel fixing set for the four side doors (Non-Puma applications). The kit comprises M8 countersunk Allen-head bolts, J...

Door Bolt Kit - a stainless steel fixing set for the four side doors (Puma applications). The kit covers both the front and rear side doors. Stain...

Safari Door Bolt Kit - a stainless steel fixing set for the rear safari (third) door, for Puma applications. The Torx-head bolts secure the fixing...

Bonnet Hinge Bolt Kit - a set of stainless steel fixings for mounting the bonnet hinges that allow the bonnet to pivot open. The kit secures the h...