Products

Exhaust Manifold Stud secures the manifold to the cylinder head on the 4-cylinder engine. It threads into the head and carries the manifold flange...

Sealing Washer for the cylinder block oil jet adaptor on the 2.5L 4-cylinder diesel engine. Seals the jet adaptor against the cylinder block. Fitt...

Interior Trim Fastener - a grey drive-in fastener for securing interior trim panels in the cabin. It retains facia and carpet trim, the cubby box,...

Fir Tree Fastener secures interior body and roof trim panels to the vehicle structure. The ribbed, tapered fir-tree shank pushes into a panel hole...

Spring Plate that retains the soft top (tilt) hood frame. Works with the tilt stud to clamp the canopy in place. Used with stud AFU2503 and ring A...

Blanking Plug for closing a 1-5/8" hole in bodywork or panels. Seals an unused aperture or grommet hole in body panels, brackets and pedal/electri...

Nut - M10 is an M10 fixing nut for general assembly and repair use across the vehicle. It threads onto an M10 stud or bolt to secure a fastened jo...

Relay

Courtesy Light Switch is a door-actuated contact switch in the interior lighting circuit, mounted at the door pillar aperture. When the door is op...

Bulb - 501 is a 12V 5W capless wedge-base bulb, designated W5W. The one-piece glass base pushes directly into the holder, with the contact wires f...

Nut Plate for the body-side striker mountings, part of the door and tailboard latch assembly. The plate provides captive threaded anchor points be...

Plate Nut

Nut Plate - captive fixing plate used at the rear body upper mountings. The plate holds the nut captive behind a blind or closed panel section, so...

Spire Nut (U-type spire fastener) for trim and panel fixings. Spring-steel push-on nut that clips over a panel edge or stud to provide a captive f...

Anchor Stud providing a threaded fixing point for interior trim panels, door casings, carpet sections, and air intake duct components. This stud a...

Spire Nut - No. 10 U-Type for use in dashboard and body panel fixings on Land Rover Defender and Discovery I. This U-type spire nut clips onto she...

Spring Nut - Metal U-Clip for body panel and electrical component fixings across a range of Land Rover models. This metal U-clip spire nut clips o...

Spire Nut is a spring-steel sheet-metal fastener that clips over a panel edge or into a pierced hole to provide a threaded anchor point. The arche...

Side Trim Panel is an interior body trim panel that lines and finishes the right-hand side of the 90" wheelbase bodyshell. It conceals the inner bo...

Rear Lower Body Side Panel - an exterior bodywork panel forming the lower rear section of the side body structure. It provides the outer skin below...

Rear Wheelarch Eyebrow Moulding - Unpainted for the Defender body exterior. This moulding fits over the rear wheelarch aperture, covering the body...

Wheel Arch Moulding – Rear An eyebrow trim moulding fitted to the rear wheel arch lip. It follows the curve of the wheel arch flange, covering the...

Eyebrow Moulding

Door Latch Adjuster. Part of the door latch mechanism, it sets the striker engagement so the door aligns, closes and seals correctly. It serves the...

Door Glass for the front door, left-hand side, in clear (un-tinted) glass. This is the sliding window pane that runs in the door channels and is ra...

Door Glass for the front door, right-hand side, in clear glass. This is the main glass panel for the front door, forming part of the door glazing ...

Body Seal seals the joint between the rear upper body panel and the lower body section.

Rear Upper Waist Seal. It seals along the upper waist line of the rear body, closing the joint between the body side and the glass line to keep out...

Front Outer Wing - Aluminium - LH for the Defender outer body panel assembly. This left-hand front outer wing is manufactured in aluminium and doe...

Front Outer Wing for the right-hand side, in the no-vent configuration without the side vent aperture. This outer wing panel forms the front bodyw...

Front door latch link

Bonnet stay stick Defender

Door Sill Seal - rear, supplied as a left- and right-hand pair. This rubber seal fits along the rear door sill aperture, forming the weather seal b...

Pop Rivet - a blind (pop) rivet for fastening panels, trim and seals where access is available from one side only. The rivet is set with a hand or ...

Front Outer Wing - Left-Hand with the turbocharger aperture in the inner face. This outer wing panel forms the front bodywork over the wheel arch,...

Front Outer Wing - Left-Hand with the turbocharger aperture in the inner face. This outer wing panel forms the front bodywork over the wheel arch,...

Front Outer Wing for the right-hand side, in the plain configuration without the turbo aperture. This outer wing panel forms the front bodywork ov...

Bolt - fixing bolt with an ACME (trapezoidal) thread form, used to secure the outer front wing to the bulkhead. It fastens the rear mounting flang...

Body Seal - Rear Lower - RH Lower rear body seal for the right-hand side. It seals the joint between the lower rear body panel and the adjacent bo...

Body Seal - Rear Lower - LH Lower rear body seal for the left-hand side. It seals the joint between the lower rear body panel and the adjacent bod...

Body Seal - Rear Upper for the right-hand side of the rear body section, part of the body sealing assembly. Fitted along the upper edge of the rea...

Body Seal - Rear Upper for the left-hand side of the rear body section, part of the body sealing assembly. Fitted along the upper edge of the rear...