Products

Circlip - LT77 Mainshaft is a retaining circlip used on the mainshaft of the LT77 5-speed manual gearbox. It seats in a groove on the mainshaft to...

Thrust Washer is a 1.25mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Thrust Washer for the differential assembly within the LT230 transfer box. This 1.35mm thrust washer sits within the LT230 centre differential, co...

Flanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...

Bolt M8 X 16 HTSETS 8.8 S/COL sold EACH

Set Screw, a hexagon-head metric fastener, M10 x 25mm. In Land Rover terminology a set screw is a bolt threaded along its full length rather than ...

Flanged Bolt, M10 x 30 mm. A metric bolt with an integral flange beneath the hexagon head that spreads clamping load over a wider area and helps re...

Differential Fixing Bolt used on the front and rear axle differential assemblies. It is one of the bolts securing the differential assembly, clamp...

Thrust Washer for the front axle swivel pin housing. The washer sits at the swivel pin bearing to set end-float and carry thrust loads within the ...

Swivel Pin Bush - Upper is the upper pivot bush in the front axle swivel housing assembly. It seats in the top of the swivel housing and locates t...

ABS Ring - the rear reluctor (exciter) ring in the anti-lock braking system. Mounted at the rear, it is the toothed ring the wheel speed sensor re...

Selector Roll Pin for the LT77 and R380 5-speed manual gearboxes. The roll pin secures a selector fork to its selector shaft, locking the two toge...

Transfer Box High Output Gear forms part of the high-range output train within the LT230 transfer box. When high range is selected it transmits dr...

Mainshaft Circlip - LT77 is a retaining circlip fitted to the mainshaft of the LT77 5-speed manual gearbox. It locates in a groove on the mainshaf...

5th Gear - LT77 is the mainshaft-mounted overdrive gear for the LT77 5-speed manual gearbox, located at the rear of the transmission in the 5th-gea...

Swivel Pin Bearing is the upper needle-roller thrust bearing in the front axle swivel housing assembly. It mounts on the upper swivel pin and carr...

Swivel Pin Thrust Washer - Upper is the shim washer that sits above the upper swivel pin bearing in the front axle swivel housing assembly. It set...

Rear Axle Breather Pipe vents the rear axle casing. It equalises internal air pressure as the axle heats and cools, allowing the casing to breathe...

Selector yoke spherical bush

Layshaft Bearing for the R380 five-speed manual gearbox. This taper roller bearing supports the layshaft (countershaft) within the gearbox casing, ...

Clutch Slave Cylinder for the manual transmission clutch release hydraulic circuit. It is fed by the clutch master cylinder and mounts at the gearb...

Needle Roller Bearing for the R380 manual gearbox. It carries the reverse idler on the layshaft, allowing the gear to rotate with minimal friction ...

Brake Mudshield is the splash shield fitted behind the right-hand rear brake disc. Mounted to the rear hub assembly, it shields the disc and braki...

Rear Brake Mudshield (Left-Hand) is a stamped backing plate that fits behind the rear brake disc within the rear disc brake assembly. It shields t...

Differential Reconditioned 10 Splines

Upper Front Swivel Pin for the front axle swivel housing assembly. The upper swivel pin bolts to the top of the swivel housing and forms the upper...

Clutch Release Fork is the pivoting lever in the clutch release mechanism that acts on the release bearing. Operated by the clutch slave cylinder ...

Clutch Release Fork - Heavy-Duty is the pivoting lever in the clutch release mechanism that acts on the release bearing. Operated by the clutch sl...

Clutch release fork is used in the clutch release mechanism of manual transmission systems. The fork operates within the clutch housing and conve...

Front Stub Axle for the front hub and swivel pin housing assembly at the front axle. The stub axle passes through the swivel pin housing and provi...

Joint Washer - LT77 Front Cover seals the mating face between the front cover and the main casing of the LT77 5-speed manual gearbox. The washer p...

Front Hub Lock Washer located within the Front Hub & Driveshaft Assembly, securing the hub bearing retaining nut in position. The lock washer ...

Stub axle

Half Shaft for the rear axle drive, right-hand side, 24-spline. The half shaft transmits drive from the rear differential to the rear hub. Its inn...

Half Shaft for the rear axle drive, left-hand side, 24-spline. The half shaft transmits drive from the rear differential to the rear hub. Its inne...

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

Mainshaft Taper Roller Bearing supports the mainshaft at the 5th/reverse end of the R380 (and LT77) 5-speed manual gearbox. It carries the mainsha...

Selector Fork is the 1st/2nd gear selector fork for the 5-speed manual gearbox. It engages the 1st/2nd synchroniser sleeve, moving it along the ma...

Selector Fork for the 3rd and 4th gear positions in the five-speed manual gearbox (LT77 and R380). The fork engages the 3rd/4th synchro hub sleeve...

Baulk Ring for the R380 5-speed manual gearbox synchromesh assembly. The baulk ring (also known as the synchromesh ring) is the friction cone elem...

Swivel Joint Washer located within the Swivel Pin Housing Assembly, sealing the interface between the swivel housing flange and the axle beam face....

Swivel Pin Gasket seals the joint between the swivel pin housing and the axle case on the front axle. It sits at the mating face where the swivel ...

Joint washer (non-ABS)

Joint Washer - 4-Wheel ABS installed at the stub axle interface in the hub assembly of vehicles equipped with 4-wheel ABS. This asbestos-free gask...

Circlip for the R380 5-speed manual gearbox mainshaft. The clip locates on the mainshaft in the 5th/reverse gear section of the main gear cluster. ...

Transfer Box Gear Lever Knob fitted to the LT230 transfer box gear lever in vehicles where the LT230 is paired with the LT77 main gearbox. The lev...

Baulk Ring for the LT77 5-speed manual gearbox synchromesh assembly. The baulk ring is the friction cone element of the synchromesh unit. It conta...