Products

Bolt - M8 x 100mm hex head bolt used in the transmission mounting assembly. Secures transmission mounting components on Series III vehicles equipp...

Bolt - Bracket to Chassis is an M10 x 60 mm fastener that secures a bracket to the vehicle chassis frame. It has a 10 mm nominal thread diameter a...

Bolt - a metric hexagon-head bolt measuring M10 x 110mm. This is a general-purpose threaded fixing used at structural and chassis mounting points,...

Panhard Rod Bolt - a metric hexagon-head bolt measuring M14 x 80mm, used to secure the Panhard rod within the axle location. The Panhard rod locat...

Bolt for the engine front cover. Hexagon-head threaded fastener securing the timing front cover on the V8 petrol engine. Supplied individually.

High-Tensile Hexagon-Head Bolt - an imperial 7/16" UNF fixing bolt, 2-1/2" long, in high-tensile grade. A general-purpose hex-head fastener with a...

Panhard Rod Bolt with a 1/2" UNF (Unified National Fine) imperial thread and a 3-1/4" shank length, manufactured to a high-tensile grade. Secures ...

Top Link Bolt - 3/4 UNF x 4 inch hexagon head bolt for securing the front top link (upper radius arm) at the fulcrum and ball joint mounting points...

Rear End Door Hinge - Upper for the rear end door (tailgate) assembly on Land Rover Discovery 1 and Discovery 2. This upper hinge mounts at the to...

Rear End Door Hinge - Lower for the rear end door (tailgate) assembly on Land Rover Discovery 1 and Discovery 2. This lower hinge mounts at the ba...

Clutch Slave Cylinder Repair Kit for the hydraulic clutch release circuit on V8 petrol applications. The clutch slave cylinder is actuated by hydr...

Gearbox Selector Ball is a hardened steel detent ball used in the manual transmission gear-selection mechanism. Spring-loaded against the selector...

Firtree Clip - a push-in fastener with a ribbed, fir-tree profile that grips into a pre-drilled panel hole. Used to secure trim panels, wiring loo...

Differential Shim, 0.074in, used during differential build to set bearing preload and gear alignment. It sits against the differential carrier sid...

Camber Bush Set for the front radius arms, 38mm wide. The bushes locate in the front radius arm mountings and set the caster and camber geometry o...

Transfer Box Flange Bolt - a 3/8" UNF x 1-1/4" hex-head bolt for the LT230 transfer case front output flange. It secures the drive flange to the f...

Radiator with Integrated Oil Cooler - the main engine cooling radiator for the 200 TDi diesel engine, incorporating a built-in engine oil cooler an...

Radiator Core is a replacement copper cooling core for the 300 TDi radiator, supplied as the core only without the top and bottom tanks. It is int...

Heater Hose - the inlet hose in the heater coolant circuit on the V8 twin-carburettor petrol engine. It carries hot coolant from the engine to the...

Heater Inlet Hose is the coolant feed hose supplying the heater matrix in the cabin heating circuit. It carries hot coolant from the engine to the...

Heater Outlet Hose is the coolant return hose from the heater matrix in the cabin heating circuit. It carries coolant from the outlet side of the ...

Receiver Dryer for the air conditioning system, compatible with R134a refrigerant. Installed on the high-pressure side of the A/C circuit, between...

Heater Return Hose moulded coolant hose within the heater circuit, carrying coolant from the heater matrix back to the engine cooling system. Shap...

Mirror RR Manual

Inlet Heater Hose - 300TDi - RHD

Heater Hose forming part of the engine cooling and cabin heating circuit. This hose connects within the heater circuit, routing coolant between th...

Headlamp Surround - the front-end finisher that frames the right-hand headlamp unit, locating between the headlamp aperture and the grille panel. ...

Headlamp Surround - the front-end finisher that frames the left-hand headlamp unit, locating between the headlamp aperture and the grille panel. I...

Heater Hose - Inlet carries engine coolant into the cabin heating circuit, feeding the heater matrix that warms air inside the HVAC housing. On th...

Heater Hose - Outlet returns engine coolant from the cabin heating circuit back to the engine cooling system after it has passed through the heater...

Caliper Bolt is the fixing bolt that secures the brake caliper to its mounting bracket. The same bolt specification is used across several chassis...

Hexagon Bolt - an M10 x 45 mm high-tensile bolt, property class 10.9, used in the suspension top link, fulcrum and ball joint assembly. The 10.9 g...

Castor Correction Kit - 44mm Wide Bush for the front suspension radius arm assembly on the Defender, Discovery 1, and Range Rover Classic. Lifting...

Circlip a spring-steel retaining ring that seats in a machined groove to axially locate a component on a shaft or within a bore. Used in the diffe...

Weatherstrip - Rear Window sealing strip for the rear tailgate end door glass assembly. This weatherstrip forms the perimeter seal between the rea...

Door Seal - Rear End Door is the weatherstrip seal for the rear end door. It seals the rear end door aperture against water and draught ingress.

Hose Clip - 12-20mm worm-drive hose clip suitable for hoses with an outside diameter of 12 to 20mm. This stainless-steel screw-type clip tightens ...

Hose Clip is a worm-drive band clamp used to secure flexible rubber hoses onto rigid pipe spigots and unions across the coolant, heater, fuel and i...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

Hose Clip - Jubilee - 70-92mm is a worm-drive band clamp with a clamping range of 70-92 mm. It secures a hose over its spigot or connector, compre...

Brake Pipe Clip - single-bore retaining clip for securing a rigid brake pipe to the chassis or body structure. This clip holds the brake pipe in i...

Brake Union Nut - Metric Thread for the hydraulic brake pipe circuit. This union nut seals and secures brake pipe connections at the unions throug...

Exhaust Olive is a tapered sealing ring used at the exhaust system's pipe joints. It seats between two pipe sections at a compression joint, formi...

Glass mirror D1, D2 RH

Mirror Glass for the left-hand exterior door mirror, convex profile. Part of the exterior mirror assembly. The convex curvature widens the rearwar...

Window Regulator Motor - RH is the electric drive motor for the right-hand window regulator assembly. It mounts directly to the window regulator m...

Window Regulator Motor - LH is the electric drive motor for the left-hand window regulator assembly. Mounted directly to the regulator mechanism, ...

Differential Pan Cover with integral filler plug, for repair of the front differential housing. This weld-in cover replaces the pressed pan sectio...