Products

Hose - Heater Water

Coolant Level Warning Sensor for the engine cooling system. This sensor is fitted to the coolant expansion tank and monitors coolant level via an ...

Coolant Hose Assembly for the 2.7L TDV6 (Lion V6) diesel engine cooling circuit, supplied as a moulded hose assembly with the thermostat and its ho...

Air Filter - the air cleaner element for the engine air intake system. The element sits within the air cleaner housing and filters incoming air be...

Mass Air Flow Sensor - air mass meter fitted in the induction tract as part of the engine management system. The sensor sits in the intake ducting...

Intercooler for the turbocharged 2.7L TDV6 diesel charge-air system. It sits between the turbocharger and the inlet manifold and cools the compress...

Hose

Belt Tensioner - 4.4 V8 AJ is the automatic tensioner of the accessory (auxiliary) drive belt system, holding the correct running tension on the pr...

Belt Tensioner - 4.4 V8 AJ is the automatic tensioner of the accessory (auxiliary) drive belt system, holding the correct running tension on the pr...

Belt Tensioner Pulley for the auxiliary drive belt system on the 2.7L TDV6 Diesel engine. This pulley maintains correct tension on the auxiliary d...

Belt Tensioner Kit - 2.7 TDV6

V-Belt

Auxiliary Drive Belt for the 2.7L TDV6 diesel engine on vehicles without an active roll stabiliser, 2092mm. This ribbed belt transmits drive from ...

Drive Belt Bracket - accessory drive bracket for the 4.4L AJ V8 EFI petrol engine (220 kW), part of the pulleys and drive belts assembly. Bolts to...

Flywheel Bolt with hex head, securing the flywheel to the crankshaft rear flange on the 2.7L V6 Lion turbo diesel fitted with the ZF S6-53 six-spee...

Washer and Screw - a screw supplied together with its washer as a single fastener assembly. This is a multi-purpose fixing used at a range of body...

Power Steering Reservoir Cap - the screw cap that closes the power steering fluid reservoir in the hydraulic steering circuit. It seals the reserv...

Upper Front Suspension Arm, right-hand side, part of the front independent suspension. The arm locates the top of the front hub carrier to the cha...

Arm - Front Suspension

Upper Front Suspension Arm Ball Joint The upper ball joint forms the top pivot between the front upper suspension arm and the wheel knuckle, holdi...

Upper Front Suspension Arm Ball Joint The upper ball joint forms the top pivot between the front upper suspension arm and the wheel knuckle, holdi...

Anti-Roll Bar Link - Front is a drop link in the front stabilizer bar assembly. The link connects the end of the front anti-roll bar to the front ...

Anti Roll Bar Link - Front connects the front anti-roll bar to the front suspension lower arm, transferring torsional load across the axle to resis...

4

Hex Nut, M24 x 1.5mm securing the constant-velocity (CV) joint stub shaft to the wheel hub within the driveline. The nut retains the CV joint and ...

Anti Roll Bar Link

Air Suspension Line - Compressor - 500 mm is a 500 mm service length of air suspension pipe used in the compressor circuit of the electronic four c...

Air Suspension Reservoir for the Electronic Air Suspension (EAS) system. This pressure vessel (accumulator) stores a reserve of compressed air, en...

Front Knuckle - right-hand steering knuckle (hub carrier) within the front suspension and hub assembly. Carries the front wheel bearing and hub, a...

Air Suspension Transfer Relief Valve - solenoid valve in the air suspension compressor and supply circuit, mounted at the supply reservoir. Contro...

Transfer Relief Valve - Front Axle in the electronic air suspension system. Fitted in the front axle branch of the air suspension pneumatic circui...

Eccentric Washer - an adjusting washer used at the front suspension arm pivot mounting. The offset (eccentric) hole allows the arm's pivot bolt po...

Bolt Mounting bolt for the rear suspension arm. Part of the rear multi-link suspension assembly, it secures a rear upper or lower suspension arm a...

Bolt Mounting bolt for the front suspension arm. Part of the front suspension assembly, it secures a front upper or lower control arm (wishbone) a...

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

Bolt for the rear suspension assembly. This fastener is used in the rear cross member and stabilizer bar assembly, and in the rear knuckle and low...

Special Nut - secures the rear knuckle to the lower and upper suspension arms. It retains the rear suspension arm bolts at the knuckle, holding th...

Adjusting Nut is an M17 flanged nut used in the rear suspension toe link assembly. It locks the toe link adjuster at its connection to the rear kn...

Nut - an M8 x 1.25 captive U-spring nut used to mount the air suspension compressor. The spring-steel body clips over the chassis bracket to provi...