Products

Thermostat assembly

Upper Sump Gasket seals the upper oil sump section against the cylinder block within the engine lubrication system. It provides an oil-tight seal ...

Half-Length Rubber Loadspace Mat lines the floor of the luggage compartment. Moulded in rubber with a raised edge, it protects the loadspace floor...

Power Steering Pump - 2.2 TD4

Parking Sensor Speaker is the audible warning speaker for the rear parking aid system. It produces the proximity warning tone driven by the parkin...

Air filter element Freelander TD4

Exhaust Valve for the cylinder head valvetrain. It seals the combustion chamber against the exhaust port and opens to release spent gases into the ...

Throttle Housing Seal for the 2.7L TDV6 and 3.0L SDV6 diesel engines, sealing the throttle body to the air intake. The seal sits between the throt...

Bonnet Gas Strut a gas-filled telescopic support for the bonnet. It counterbalances the weight of the bonnet, assisting opening and holding it sec...

Pump - Water

O-Ring, 11mm - a sealing ring used in the power steering hydraulic circuit, at the union joints of the pressure supply and return hoses. It seats ...

Water Outlet Connection - the coolant outlet housing on the 2.7L V6 diesel engine, incorporating the thermostat that controls coolant flow to the r...

Cooler Assembly - Fuel No Gasket

Fuel Filter Element for the diesel fuel supply system. The element removes particulate contamination and separates water from the fuel before it re...

Cylinder Head Gasket - Grade 2 for the 2.7L TDV6 diesel engine. Seals the joint between the cylinder head and the engine block, containing combust...

Cylinder Head Gasket - Grade 5 for the 2.7L TDV6 diesel engine. Seals the joint between the cylinder head and the engine block, containing combust...

Sensor - Crankshaft Position - CPS

Propshaft rear Defender 130 TD4

Front wheel arch moulding cap - right-hand side, exterior body trim. The cap closes off the front wheelarch moulding where it meets the bumper, co...

Rear moulding cap - exterior body trim. The cap closes off the moulding at the junction between the rear bumper and the rear wheelarch moulding, c...

Rear wheel arch moulding cap - right-hand side, exterior body trim. The cap closes off the rear end of the rear wheelarch moulding where it meets ...

Steering Kit Gear Tie Rod Repair

Track Rod End - the outer ball joint that connects the track rod to the steering knuckle. Transmits steering movement from the track rod to the wh...

Ignition Coil for the 5.0L V8 petrol engine (AJ133), part of the ignition coil and spark plug assembly. This is a coil-on-plug unit: it mounts dir...

Exhaust Valve for the cylinder head of the 5.0L V8 petrol engine (AJ133), naturally aspirated and supercharged. It seals the exhaust port against ...

Kit - Tension Pulley

Oil Cooler Assembly - the oil-to-coolant heat exchanger of the engine's Oil Cooler and Filter assembly. Engine coolant is passed through the coole...

Gasket - Oil Cooler seals the engine oil cooler to its mounting face, within the Oil Cooler and Filter assembly. It maintains the integrity of the...

Cam Cover Gasket seals the left-bank camshaft cover to the cylinder head on the 5.0L V8 (AJ133) petrol engine. It forms the oil-tight joint around...

O-Ring - Radiator Hose

Cam Cover Gasket seals the right-bank camshaft cover to the cylinder head on the 5.0L V8 (AJ133) petrol engine. It forms the oil-tight joint aroun...

Plug cooling system bleed

Connector

Spark Plug Well Gasket seals the spark plug aperture in the camshaft (valve) cover on the right-hand cylinder head bank. It prevents engine oil fr...

O-ring for the variable valve timing (VVT) solenoid, part of the timing gear assembly at the front of the engine. The solenoid meters oil flow to ...

Vacuum Pump Seal - sealing ring between the engine-driven vacuum pump and its mounting face on the engine, forming part of the brake servo vacuum c...

Gear Selector Lever - lever that clamps to the manual selector shaft on the six-speed ZF automatic transmission, forming the gearbox end of the flo...

Retainer Clip - a quarter-turn, click-type fastener used to secure bumper trim and adjacent body panels to the vehicle body. The clip is fitted wi...

o-ring oil cooler 3,0 TDV6

O-Ring sealing the oil cooler and filter housing on the 3.0L V6 diesel engine. Positioned at the mating interface between the oil cooler assembly ...

Oil Cooler O-Ring for the engine oil cooler and filter housing assembly. The Ø 9.5mm O-ring seals the oil-carrying joint between the engine block a...

Water Pump for the engine cooling circuit on the 3.0L V6 diesel engine. This pump circulates coolant through the engine block, cylinder heads, and...

Oil Tube Gasket for the 3.0L V6 diesel engine. This sealing gasket forms a leak-free joint at an oil tube connection within the engine lubrication...

Oil Return Hose Gasket for the 3.0L TDV6 diesel engine. This gasket seals the oil return hose connection at the turbocharger, forming a leak-free ...

Camshaft Position Sensor within the engine management system of the 3.0L diesel engine. This sensor monitors camshaft rotational position and tran...

Crankcase Breather Pipe for the 3.0L V6 diesel, part of the crankcase ventilation circuit within the engine emission control system. The pipe conn...