for Discounts / VAT
for Discounts & Correct VAT
Tappet Hydraulic
Magnetic Oil Drain Plug - M14 x 21 sump drain plug in the engine lubrication system. The plug seals the drain aperture in the oil sump and is remo...
View full detailsFuel Filter for the diesel fuel supply system. This primary filter removes contaminants and water from the fuel before it reaches the high-pressure...
View full detailsAir Filter - engine air cleaner element, seated in the intake air cleaner housing upstream of the mass air flow sensor and the turbocharger inlet. ...
View full detailsSuspension Arm - Front - RH is a front control arm fitted to the right-hand side of the front suspension assembly. It locates the front wheel hub ...
View full detailsSuspension Arm - Front - LH is a front control arm fitted to the left-hand side of the front suspension assembly. It locates the front wheel hub c...
View full detailsFuel return tube O-ring seal
Latch hood, bonnet, RH and LH, with sensor
Valve - Control
PCV Valve Service Kit for the crankcase ventilation circuit of the 2.0L Ingenium petrol engine (AJ200 / AJ20P4). The positive crankcase ventilatio...
View full detailsSpark Plug - ignition spark plug for Ingenium petrol engines (AJ20 / AJ22 series, including PHEV applications). The plug screws into the cylinder ...
View full detailsWheel hub bearing for the front and rear knuckle and hub assemblies. The bearing carries vehicle load between the hub and the knuckle and allows t...
View full detailsFront Axle Drive Shaft - left-hand side, operating within the front axle drive shaft and constant velocity joint assembly. Transmits drive from th...
View full detailsAccessory Drive Belt for the engine accessory (ancillary) drive on 2.0L GTDi and second-generation 2.0L turbocharged petrol engines. The belt is d...
View full detailsAccessory Drive Belt for the front end accessory drive of the 2.0L Ingenium four-cylinder engine (AJ200 / AJ20P4, petrol and diesel applications). ...
View full detailsAnti-Roll Bar Link - Front, the connecting link between the front anti-roll bar end and the suspension strut in the front suspension assembly. The...
View full detailsBreather Cover - crankcase ventilation cover on the 2.0L AJ20P4 petrol engine, forming part of the crankcase emission control assembly. It seals t...
View full detailsCoolant Level Warning Sensor for the engine cooling system. This sensor is fitted to the coolant expansion tank and monitors coolant level via an ...
View full detailsService Kit - a single-part-number set of the filters and consumables required for a scheduled service on the 2.0L AJ200 single-turbo diesel engine...
View full detailsDust Cap for a brake bleed nipple. This small protective cover fits over the bleed screw on a brake caliper or wheel cylinder. It keeps dirt and m...
View full detailsWinch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...
View full detailsRubber Loadspace Mat - a moulded protective mat for the load compartment floor. The mat lies over the loadspace carpet and is shaped to the floor ...
View full detailsDog Guard - a load compartment partition separating the loadspace from the passenger cabin. The guard mounts behind the rear seat backs and stops ...
View full detailsPlain Washer is a flat fastening washer used in mechanical assembly. It seats under a bolt head or nut to spread the clamping load across the join...
View full detailsExhaust Gasket sealing a flanged joint in the exhaust system on Land Rover and Range Rover models fitted with the 2.7L TDV6, 3.0D V6, 2.2D, and 4.4...
View full detailsWheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...
View full detailsWheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...
View full detailsMicro Relay is a 20 amp, 4-pin switching relay used within the vehicle electrical system to control a high-current circuit from a low-current signa...
View full detailsWiper Relay is a 5-pin mini relay used in the wiper control circuit to switch the supply to the wiper motor. The five-pin layout provides a change...
View full detailsRelay, a 70A 4-pin grey mini power relay. It provides high-current make-and-break switching for a heavy electrical load, letting a low-current con...
View full details