Products

U-Bolt - a rear leaf-spring axle clamp. It passes around the axle tube and clamps the rear leaf spring to the axle seat via the lower spring plate...

Front Towing Eye / Lifting Ring bolts to the front of the chassis, providing an anchored attachment point for towing, recovery and lifting. The ri...

Stub Shaft with a 10-spline drive coupling, a component of the axle half-shaft assembly. The stub shaft sits within the axle and transmits drive t...

Propshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...

Front Spring Dowel for the 9-leaf front road spring, part of the leaf spring suspension assembly. The dowel is the centre locating pin that passes...

Wheel Cylinder for the drum brake assembly - the right-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either...

Wheel Cylinder for the drum brake assembly - the left-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either ...

Wheel Cylinder for the rear drum brake assembly, right-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hy...

Wheel Cylinder for the rear drum brake assembly, left-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hyd...

Spring Clip - a retaining clip in the transfer gearbox selector linkage. It secures the transfer lever to its pivot, holding the gear-change lever...

Front left-hand wheel cylinder for the hydraulic front braking system, installed within the brake backplate assembly of 11-inch front brake configu...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Outer Distance Piece for the front axle swivel pin housing. The distance piece is a spacer that sets the position of the swivel pin bearing within...

Exhaust Connecting Pipe is the intermediate section of the exhaust system for Series short wheelbase vehicles fitted with the 2.25L diesel engine, ...

Oil Pump Lock Tab, part of the engine oil pump assembly. The lock tab is a tab washer fitted under the oil pump retaining fastener; once the faste...

Gear - 2nd - Pair for the Series Land Rover four-speed main gearbox. This pair comprises the matched 2nd speed gears for both the mainshaft and th...

Flywheel Housing O-Ring - a sealing ring at the rear of the engine where the flywheel housing meets the cylinder block. Fitted to the 2.25L engine...

Cylinder Head Bolt - a clamping bolt securing the cylinder head to the engine block. It draws the head down onto the block to compress the head ga...

Domed Nut with a 5/16 UNF thread, a finishing fastener. The domed (acorn) form encloses the end of the stud or bolt it threads onto, protecting th...

Oil Gallery Plug for the cylinder block oil gallery on Land Rover 4-cylinder engines. The oil gallery is the network of internal drillings in the ...

Manifold Stud - a mounting stud for the manifold. Threaded into the cylinder head, it locates the manifold and clamps it to the head face via its ...

Valve Stem Oil Seal fits over the inlet valve stems to limit oil consumption past the valve guides in the cylinder head. It is used on 2.25L petrol...

Lock Washer secures a threaded fastener against loosening under vibration and thermal cycling. Fitted beneath the nut or bolt head, it bites into ...

Water Pump Impeller in the engine cooling circuit. Pressed onto the water pump spindle and driven by the fan belt, the impeller circulates coolant...

Heater Plug Lead in the diesel glow plug pre-heat circuit. This 10" interconnecting lead links the No.2 and No.3 heater (glow) plugs, carrying cur...

Glow Plug Lead in the diesel glow plug (heater plug) pre-heat circuit. This short 5" lead interconnects glow plugs wired in series and is not inte...

Bolt securing the gearbox to the transfer box in the drivetrain. This fixing clamps the main gearbox housing to the transfer box. It applies to th...

Lock nut 3/8" BSF

U-Bolt Nut - 7/16 BSF for use in the leaf spring suspension assembly. U-bolts clamp the leaf spring pack to the axle casing at the front and rear ...

Wheel Cylinder Overhaul Kit for front drum brake systems fitted with 11-inch brake drums. This kit provides the necessary parts to overhaul all fo...

Wheel Cylinder Repair Kit A seal repair kit for overhauling the rear brake wheel cylinders, part of the drum braking system. The wheel cylinder si...

Sealing ring

Oil Filter Bowl Bolt Washer - rubber sealing washer for the oil filter bowl centre bolt. Fitted to the centre bolt that retains the oil filter bow...

Water Pump - 2.0 IOE - the engine coolant pump in the cooling system, for the 2.0L IOE (inlet-over-exhaust) petrol engine. Driven by the fan belt ...

Lock Washer is a folding lock tab used in the front axle swivel pin housing assembly. Fitted beneath a 3/8" stud fixing, the tab is bent up agains...

Shackle pin

O-Ring Seal - sealing ring for the steering box rocker shaft. Fitted around the rocker (sector) shaft where it passes through the steering box hou...

Ball Race - Steering Box (Adjusting) is a component of the recirculating-ball manual steering box assembly, used to control pre-load and end-float ...

Rubber Sealing Ring for gear selector shafts in the LT76 gearbox and LT95 transfer box. In the LT76 gearbox, two rings are fitted per unit, sealin...

Handbrake Drum is the drum for the transmission-mounted parking brake, for use with the LT76 gearbox. Mounted at the rear of the gearbox on the tr...

Fuel Pump Gasket for the 2.0L diesel engine (Series II) and 2.25L diesel engine (Series IIA). This gasket seals between the mechanical fuel pump b...

Wheel Cylinder Repair Kit for overhauling a front drum-brake wheel cylinder with a 1.25 inch bore. It restores the hydraulic seal of a worn or lea...

Exhaust Pipe - Intermediate - Non-Station Wagon

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Swivel Housing Gaiter Kit in leather for the front axle swivel housings, supplied as an axle set to cover both sides. The gaiter encloses the swiv...