Products

Swivel Pin Housing Locking Plate mounts to the front axle swivel pin housing. It locks the swivel pin in position and provides the fixed stop that...

Bolt with a 3/8" UNF (Unified National Fine) thread and a 1-7/32" length. A standard imperial-thread fastener for chassis, driveline and body fixi...

Breather Set Screw secures the breather to the rocker cover within the engine crankcase ventilation arrangement. It retains the breather against t...

Spring plate

Drain Plug Washer in copper, used to seal axle differential drain plugs against oil leakage. This copper crush washer seats under the drain plug a...

Axle Breather for the front axle housing on vehicles without a remote breather pipe assembly. This screw-in vent allows the air inside the front a...

Screw - a set screw for the gearbox top cover plate. It secures the cover plate to the top of the main gearbox casing. Not used on the Stage 1 V8 ...

Steering Relay Arm - Upper is the upper lever of the steering relay unit, the vertical relay mounted on the front chassis crossmember that transfer...

Lower Swivel Pin O-Ring for the front axle swivel housing assembly. It seals the joint at the lower swivel pin, where the steering arm and lower pi...

Upgrade and restore the swivel housing assembly on your Land Rover Series 2 with this swivel pin conversion kit. Designed for improved durability a...

Steering Relay Shaft Bush - Split Half for the steering relay assembly on classic Land Rover models. This bush is supplied as one half of a split ...

Drain Plug for the gearbox, transfer box and axle casings. It threads into the drain point at the base of the casing to retain the oil in service, ...

Oil Filler Breather Cap of the top-hat type closes the oil filler on the cylinder head side cover and vents the crankcase. It combines the oil fil...

Fuel Sender Unit Gasket for the fuel gauge sender unit fitted to the fuel tank. This gasket seals the joint between the sender unit flange and the...

Spring Bush for the leaf spring suspension system on Series Land Rovers. This rubber bush fits into the spring eye at the front fixed mount and re...

Reflector SIII

Shock Absorber Bush Set for the shock absorber mountings. This set provides the bushes that locate each shock absorber at its mounting eyes, insul...

Shock absorber bush (eye), anti roll bar bush

Upgrade your Series Land Rover suspension with this Polyurethane Shock Absorber Bush Set in black. The set includes 4 pieces, providing everything ...

Polyurethane Bush Set in yellow, supplied for suspension mounting points that use a rubber-style bush. Supplied as a set of yellow polyurethane bu...

Gear Selector Plunger is the interlocker pin fitted to the 1st and 2nd gear selector shaft in the gearbox top cover. It prevents simultaneous selec...

Wheel Cylinder Bleed Screw fits into the bleed nipple port of the wheel cylinder in the drum brake assembly, allowing the hydraulic circuit to be p...

Gearbox Selector Shaft Pin - an interlock pin within the gearbox selector mechanism. It sits between the selector shafts (rails) and prevents more...

Gearbox Bearing is the ball bearing that supports the primary pinion, or first motion shaft, in the main gearbox. Located at the front of the gear...

Gearbox Stud is a 1 3/4" threaded stud used in the gearbox and transfer box assembly. It provides a fixed threaded anchor for clamping casing join...

Hot plug hot spot 2.25 diesel

Exhaust Hanger Plate - a flexi-mount bracket within the exhaust system mounting hardware. It suspends the exhaust from the vehicle underframe, its...

Series 2, 2A, 2B and Series 3: - 1-Ton, Lightweight and Militairy models. Series 1: - 107".

Transfer Box Intermediate Shaft Shim, 0.005in thick, used in the transfer box to set the end float of the intermediate gear on its shaft. Selectiv...

4WD High Gear Selector Spring for the transfer box four-wheel-drive selector mechanism. The spring acts on the high-range four-wheel-drive selecto...

Wheel Stud, screw-in type, 9/16 BSF and threaded at both ends, fitting the front and rear axle hubs. The stud screws into the hub at one end; the ...

Clutch Withdrawal Tube fitted in the clutch cross-shaft withdrawal mechanism on Series II, IIA, and III Land Rovers. This tube forms the connectin...

Exhaust Silencer for right-hand-drive applications. Part of the exhaust system, this silencer attenuates combustion noise as the gases pass throug...

Drop Plate Strengthener for the towing equipment assembly. It acts as a spacer and strengthener for the towing jaw and the towing jaw/ball fixings...

Front Exhaust Pipe forms the front section of the exhaust system, mounting to the exhaust manifold by a four-stud flange. It carries exhaust gas f...

Exterior Mirror - Round Arm is a complete wing mirror assembly comprising a round convex mirror head and a standard-length mounting arm, designed f...

Front Bumper in galvanised steel, mounting across the front of the chassis frame. It bolts to the front chassis dumb-irons to provide front-end im...

Bulb rated 12V 4W with a small-diameter fitting, part of the vehicle lighting system. This low-wattage bulb suits the small-fitting (Lucas-type) l...

Drive Member - 10-Spline is the drive coupling at the outer end of the axle, forming part of the wheel hub and drive assembly. Its 10-spline inter...

4WD Selector Rod for the Series transfer box. It forms part of the four-wheel-drive engagement linkage, transmitting selector movement through the...

Wheel Nut, Flat Type secures the road wheel to the hub studs. It has a flat, single-chamfer seating face and a 27mm hexagon.

Gear Lever Knob threads onto the top of the main gearbox gear lever to form the hand grip used for gear selection. It gives the driver a defined c...

Track Rod Clamp is a split-tube collar that secures the threaded track rod end into the track rod tube on the front steering axle. Once the front ...

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

Rear brake drum installed in the rear drum brake assembly of the vehicle braking system. The drum mounts to the rear hub and rotates with the wheel...