Products

Clutch Plate is the friction-lined driven plate of the clutch assembly, 9 inch (229 mm) diameter. Its splined hub engages the gearbox input shaft ...

Clutch Cover is the pressure plate assembly of the clutch, 9 inch (229 mm) diameter, coil-spring type with three release fingers. It bolts to the ...

Handbrake Return Spring is part of the transmission-mounted drum-type handbrake, acting on the relay lever within the parking brake mechanism. Whe...

Exhaust Manifold bolts to the exhaust ports on the cylinder head and collects the exhaust gases from the cylinders into a single outlet feeding the...

Axle Check Strap limits the downward travel of the rear axle, fitted within the rear suspension on the 1-Ton chassis running the Salisbury axle. I...

Accelerator Cable links the accelerator pedal to the injection pump throttle lever, forming part of the throttle linkage on the 2.25L diesel engine...

Choke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...

Fitment: All models to 1980 except V8

Rear Axle Stub for the rear axle assembly on early Series Land Rovers. The axle stub is the outboard section of the rear axle shaft assembly, carr...

Gearbox Gasket Kit - No Seals for the 4-speed manual gearbox and transfer box on Series models. This set supplies the paper and fibre mating gaske...

Thermostat for the engine cooling system, with an 82°C opening temperature. The thermostat regulates coolant flow between the engine and the radia...

Round Mirror Head is the circular exterior mirror glass and housing that mounts on a wing- or fender-mounted mirror arm. It gives the driver a rea...

Hub Nut Spanner for the front hub and wheel bearing assembly. The 52mm tool engages the hub retaining nut on the front stub axle. Designed for use...

Starter Pinion Retaining Kit for the inertia (Bendix) drive of the starter motor fitted to 4-cylinder and 6-cylinder petrol engines. The starter p...

Track Rod End for the steering linkage, with a right-hand thread. The track rod end is a ball-jointed coupling at the end of the track rod that co...

Gasket

Gearbox Gasket for the LT76 four-speed gearbox with integral transfer assembly. It seals a mating housing face within the gearbox and transfer cas...

Primary Pinion Bearing for the manual gearbox, supporting the primary pinion (gearbox input shaft). The primary pinion transmits drive from the cl...

Grommet

Halfshaft Retaining Collar fitted to the axle halfshaft to locate and retain the halfshaft bearing on the shaft. The collar is pressed onto the ha...

Spring Clip for the rear end door trim casing, part of the interior trim fixings. The sprung clip retains the rear door card (trim casing) to the ...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Stud used at the gearbox-to-chassis bracket mounting on Series models. A 7/16" BSF stud securing the gearbox mounting bracket to the chassis. Not ...

Spherical Bearing Bush - Clutch Cross Shaft for Series 1, Series 2, and Series 3 Land Rover vehicles. The clutch cross shaft is supported at its p...

Oil Pressure Switch for the engine lubrication system warning circuit. This pressure-sensitive switch threads into the engine block oil gallery an...

Folding side step Series

Steering Relay Gasket seals the steering relay assembly within the steering linkage. The steering relay transfers movement from the steering box d...

Accelerator Rod Ball Joint forms an articulated pivot in the accelerator (throttle) control linkage, joining adjacent sections of the accelerator r...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Upgrade your Land Rover Defender or Series vehicle with this complete 73mm LED Light Upgrade Kit. Designed to replace traditional incandescent lamp...

Voltage Regulator (control box) of the screw-terminal type, for dynamo charging systems. The control box is wired between the dynamo and the batte...

Steel Ball - 9/32 inch steel ball used in the steering column assembly. Supplied individually. Ball diameter 9/32 inch (7.14 mm).

Heater Distribution Control Cable - the Bowden cable that links the dashboard heater control to the air-distribution flap in the heater assembly. ...

Steel Wheel - a 5.5J x 16 pressed-steel rim finished in Limestone gloss. This is a tube-type rim: it is not sealed for tubeless running and must b...

Footwell Repair Panel for the right-hand (offside) footwell - a body repair section covering the footwell floor and inner side panel. For right-han...

Front Chassis Leg for the left-hand (nearside) front of the chassis. A welded chassis repair section that renews the front chassis leg where the o...

Front Chassis Leg for the right-hand (offside) front of the chassis. A welded chassis repair section that renews the front chassis leg where the o...

Fixed Towing Drop Plate bolts to the rear tow bar to carry the towball at the correct towing height. The plate is a fixed, non-adjustable type set...

Rear Spring Hanger is a chassis mounting bracket in the rear leaf-spring suspension, forming the forward anchor point that carries the front eye of...