Products

Exhaust Clamp Kit for the intermediate pipe section of the exhaust system. The kit provides the clamps that secure the intermediate exhaust pipe a...

Exhaust Clamp Kit - the clamping hardware that secures the intermediate pipe joint in the exhaust system, holding the intermediate section to its a...

Exhaust Clamp Kit for the front and intermediate exhaust sections on Series II and III Land Rovers equipped with the 2.6L six-cylinder petrol engine.

Exhaust Clamp Kit for the silencer and tail pipe section of the exhaust system on Series II and III 88-inch Land Rovers with a right-hand side exha...

Sidelight Bulb, rated 24V 10W, for the front sidelight (parking light) position. The bulb seats in the sidelight holder within the front lamp asse...

Bulb rated at 24V 5W, for use in side lamp and parking light circuits on 24V vehicle electrical systems. Small-wattage bulb designed for marker an...

Clutch Fork for the clutch actuation assembly in the gearbox bellhousing. This fork pivots on a fulcrum post within the bellhousing and translates...

Sealing Washer for diesel fuel injectors, positioned at the injector nozzle seat in the cylinder head to seal against combustion gases around the i...

Clutch Cylinder Adaptor - a pipe union that connects the hydraulic clutch supply pipe to the inlet port of the clutch master cylinder. Fitted at t...

Stop Light Switch mounts at the brake pedal and switches the rear brake (stop) lamps on when the pedal is depressed, operating within the brake-lig...

Ball Joint - Accelerator Linkage is a mechanical pivot joint used in the accelerator linkage assembly. This ball joint connects articulating rods ...

Brake Drum Screw for the brake drum assembly. This retainer screw secures the brake drum to the wheel hub flange, preventing the drum from displac...

Braided Earth Strip is a flexible braided conductor that forms an electrical earth (ground) bond between two points in the vehicle. It provides a ...

Mainshaft Bearing for the gearbox mainshaft - the centre bearing that supports the mainshaft within the gearbox casing. It locates and carries the...

Brake Servo Repair Kit for the Type 50 vacuum brake servo unit (227mm diameter). This overhaul kit contains the components necessary to rebuild th...

Valve repair kit

Lights and Heater Switch - a three-position Lucas-type toggle switch fitted to the dashboard switchgear. It acts as the master control for the exte...

Speedometer Pinion Oil Seal for the gearbox speedometer drive take-off. It seals around the speedometer drive pinion where it enters the gearbox ho...

Glazing Rubber Seal for retaining glass panels in fixed window aperture frames. This flexible rubber channel seal locates in the groove of the win...

Steering Relay Oil Seal for the steering relay unit, part of the steering linkage. The steering relay transfers movement from the steering box dro...

Exhaust Gasket sealing the exhaust manifold-to-downpipe flange on Series Land Rover 4-cylinder petrol and diesel engines. This four-hole flange ga...

Lock Nut for the Land Rover Series gearbox primary pinion bearing. This nut retains the front bearing on the primary pinion (input shaft), securin...

Small Gasket for 269974

Sump Plug Sealing Washer for the engine lubrication system. It seats between the oil drain plug and the sump pan boss, sealing the joint so the plu...

Track Rod End Boot for the steering track rod end ball joint. This rubber boot fits over the track rod end housing, sealing the ball joint against...

Track Rod End Boot Ring - spring retaining ring for the track rod end of the steering linkage. It clamps the rubber dust boot onto the track rod en...

Driving Member Bolt for the axle driving member assembly. This 3/8" BSF x 1-19/32" bolt retains the driving member to the hub assembly. The drivin...

Bolt with Whitworth (BSW) thread - 1/4 inch diameter, 1-1/4 inch length, sold individually. Used across Series Land Rover applications requiring t...

Brake Clevis A clevis for the brake drum expander mechanism within the drum braking system. It forms the pinned link between the brake operating r...

Clevis Pin - pivot pin used in the mechanical brake and transmission linkages. It passes through a forked clevis and the eye of a mating rod or lev...

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Double-Grooved Ball Bearing for the manual gearbox and transfer box. It supports and locates a rotating shaft within the casing, carrying the radia...

Axle Key Washer for the hub nut locking system in the axle assembly. This tab washer seats beneath the axle hub nut, with tabs that locate into ma...

Outer Hub Lock Washer for the front and rear hub assembly on Land Rover solid axles. This lock washer secures the hub bearing retaining nut agains...

Wheel Nut for the road wheel and hub assembly, securing the road wheel onto the hub studs. The double-chamfer design is tapered at both ends, so t...

Oil seal

Lock Washer for the gearbox mainshaft, securing the special retaining nut where the mainshaft meets the transfer box. A tab washer whose tang is b...

Mainshaft Nut for the LT76 gearbox, fitted to the mainshaft and gear assembly. It retains the gear cluster on the mainshaft, clamping the stack ag...

Output shaft bearing

Pinion Bearing Retaining Plate for the Power Take-Off (PTO) unit on Series Land Rovers. This retaining plate locates and secures the pinion bearin...

Bolt for the LT76 gearbox assembly, with a 5/16" BSF (British Standard Fine) thread. Used as a threaded fastener within the gearbox casing.

Transfer Box Mainshaft is the central rotating shaft within the transfer box assembly, running through the gear train and transmitting drive betwee...

Gearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...

Starting Handle for manual cranking of the engine. The handle engages the dog on the front of the crankshaft, allowing the crankshaft to be turned...

Brake Shoe Spring for the drum brake assembly on Land Rover vehicles. This return spring pulls the brake shoes back from the drum face after each ...

Drive Shaft Hub Cap for the hub assembly on Land Rover Series vehicles. This cap fits at the outer face of the hub, closing off the drive shaft en...

Transfer Lever Knob in red, for the high/low range selector on the transfer gearbox. It threads onto the top of the transfer change lever and prov...