Products

Rear Leaf Spring for Series IIA and Series III 109" wheelbase 1-ton and Extra Heavy Duty Land Rovers. Suitable for both left-hand and right-hand si...

Engine Plug (3/8 BSF thread) for Land Rover 4-cylinder petrol and diesel engines. This threaded blanking plug is used at multiple points across th...

Clevis Pin for the clutch cross shaft, part of the mechanical clutch release linkage. The pin forms the pivoting joint that connects the clutch op...

Barrel Lock & Key is the lock barrel and matching key for the ignition/starter switch. This is the diesel-application barrel for the earlier t...

Wheel Brace for loosening and tightening road wheel nuts. It has a 15/16 in AF (approximately 24mm) hexagon socket, sized for the wheel nuts fitted...

Spring Shackle Plate forms part of the rear leaf spring shackle assembly, pairing with the shackle pins and bushes to connect the swinging eye of t...

Shackle plate

Shackle plate

Shackle Plate for the rear leaf spring shackle assembly. The shackle plate links the rear eye of the leaf spring to the chassis mounting, allowing ...

Shackle Pin (9/16 UNF × 4-3/8 in.) for the rear leaf spring assembly on Land Rover Series vehicles. This is the short shackle pin, fitted at the r...

Shackle Pin (9/16 UNF × 4-1/2 in.) for the leaf spring suspension on Land Rover Series vehicles. This medium-length pin is used at the forward (ch...

Shackle Pin - Long (9/16 UNF × 5-1/4 in.) for the front leaf spring shackle on Land Rover Series vehicles. This long shackle pin is fitted at the ...

Steering Relay Shaft Bush - Split Half for the steering relay assembly on classic Land Rover models. This bush is supplied as one half of a split ...

Joint Washer - front timing cover gasket for Land Rover 4-cylinder petrol and diesel engines. This gasket seals the mating face between the front ...

Crankshaft Thrust Washer controls crankshaft end-float - the axial movement of the crankshaft within the block - at the centre main bearing. The w...

Crankshaft Thrust Washer - 0.0075in oversize, supplied as a pair. Fitted at the centre main bearing of the four-cylinder engine to control cranksh...

Crankshaft Thrust Washer - 0.010in oversize, supplied as a pair. Fitted at the centre main bearing of the four-cylinder engine to control cranksha...

Water Pump Gasket - 9-Hole for the cooling system on Land Rover Series 2.25L Petrol engines. This gasket seals the mating face between the water p...

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Railko Bush is the lower swivel bearing in the front axle swivel pin housing. It locates the bottom swivel pin and provides the low-friction pivot...

Drain Plug for the gearbox, transfer box and axle casings. It threads into the drain point at the base of the casing to retain the oil in service, ...

Dipstick Tube for the engine lubrication system on non-V8 four- and six-cylinder engines. The tube fits into the cylinder block and guides the oil ...

Crankshaft Rear Oil Seal Kit - Cork for the rear crankshaft sealing assembly on Series Land Rover engines with a 3-bearing crankshaft. This kit su...

Crankshaft Oil Seal Kit for a full rear crankshaft seal replacement on Series Land Rover engines with a 3-bearing crankshaft. This kit includes tw...

U-Bolt for the leaf spring suspension, clamping the front leaf spring to the axle. This is the short, round-top type with a 7/16" BSF thread. It p...

Fuel Filler Hose - SWB for the fuel filler assembly on Series Land Rovers equipped with an under-seat fuel tank. This rubber hose connects the ext...

Fuel Filler Breather Hose, part of the fuel filler and tank ventilation system. The hose vents air displaced from the fuel tank during refuelling,...

Fuel Tank Plate - Rear Fixing is the mounting plate used to secure the rear of the fuel tank on 88" wheelbase Series Land Rovers. It provides the s...

Fuel Tank Suction Pipe for the under-seat fuel tank. The pipe forms the tank-side pickup of the fuel supply circuit, drawing fuel from within the t...

Oil Filler Breather Cap of the top-hat type closes the oil filler on the cylinder head side cover and vents the crankcase. It combines the oil fil...

Sump Gasket seals the joint between the sump (oil pan) and the base of the cylinder block on the 2.6L six-cylinder IOE petrol engine. It forms the...

Fuel Sender Unit Gasket for the fuel gauge sender unit fitted to the fuel tank. This gasket seals the joint between the sender unit flange and the...

Engine Push Rod for diesel engine valve actuation, operating within the cylinder head valve train. The push rod transmits motion from the camshaft...

Sump Gasket - 4-Cyl for the engine sump sealing joint on Land Rover 4-cylinder engines. This gasket seals the mating face between the sump pan and...

Brake Shoe Return Spring for the rear drum brake assembly, fitted at the upper end of the brake shoes adjacent to the wheel cylinder. The spring h...

Spring Bush for the leaf spring suspension system on Series Land Rovers. This rubber bush fits into the spring eye at the front fixed mount and re...

Spring Bush - Polyurethane for the leaf spring suspension system on Series Land Rovers. This polyurethane bush fits into the spring eye at the fro...

Distributor Coupling - drive coupling for the distributor. Transmits drive to the distributor shaft on the 2.25L and 2.5L petrol engines.

Core Plug seals a casting aperture in the cylinder block or head of the 2.25L and 2.5L four-cylinder petrol engines. Also known as an expansion or...

Clutch Release Bush for V8 petrol applications, located within the clutch assembly at the rear of the crankshaft. The bush seats in the spigot rec...

Ignition Switch is the key-operated electrical switch mounted on the steering column, at the heart of the ignition and starting circuit. It selects...

Reflector SIII

Clutch Hose for the clutch hydraulic circuit, 1/4" bore. This flexible hydraulic hose carries fluid from the clutch master cylinder to the slave c...

Fuel Tank for the 88" short-wheelbase chassis, forming the main fuel store within the fuel supply system. This is the early front-filler configura...

Exhaust Pipe - Front

Shock Absorber Bush is a rubber mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chassis and axle attachme...