Products

Injector Pipe - the high-pressure fuel line serving the No.4 cylinder on the 2.25L diesel. It carries metered fuel from the injection pump outlet ...

Oil Filler Cap O-Ring seals the oil filler cap to the rocker cover. It forms an oil-tight seal at the cap-to-cover joint, preventing oil leakage a...

Inlet Manifold Joint Washer seals the inlet manifold to the cylinder head. It maintains an airtight joint between the manifold flange and the head...

Manifold Clamp - a clamping plate that secures the manifold to the cylinder head. It fits over the manifold flange and draws down onto the cylinde...

Diesel Injector for the fuel injection system, delivering metered, atomised fuel from the injection pump into the engine. Fitted to the 2.25L and ...

Front Bumper in galvanised steel, mounting across the front of the chassis frame. It bolts to the front chassis dumb-irons to provide front-end im...

Master Cylinder Nut for the CB-type brake master cylinder, fitted to the end of the cylinder bore. The nut closes and retains the end of the maste...

Expansion Tank Cap seals the cooling system expansion (header) tank. The plastic cap closes the tank and holds the coolant circuit at its rated pr...

Radiator Overflow Hose carries coolant overflow away from the radiator filler neck. It connects to the overflow spigot on the radiator filler neck...

Expansion Tank Hose connects the coolant expansion (header) tank into the cooling circuit. It carries coolant between the expansion tank and the r...

Joint Washer for the radiator cap, part of the engine cooling system. This sealing washer seats between the radiator cap and the filler neck, main...

Brake pipe

Accelerator Cable in the throttle control linkage, connecting the accelerator pedal to the carburettor throttle spindle. Transmits pedal movement ...

Spark Plug for low-compression (7:1) petrol engines fitted with screened ignition on 24V FFR (Fitted For Radio) vehicles. The screened design supp...

Distributor Cap mounts at the top of the distributor in the ignition system and carries the segment contacts that route high-tension voltage to the...

Water seal

Crankshaft Timing Sprocket mounts on the nose of the crankshaft and forms part of the timing drive. Its teeth engage the timing chain to drive the...

Glow Plug (cold-start heater plug) threaded into the cylinder head, part of the diesel cold-start heating circuit. The heated tip projects into th...

Flywheel Ring Gear (starter ring gear) for the diesel flywheel, part of the clutch and flywheel assembly. The toothed ring is fitted around the fl...

Exhaust Stud - Manifold to Front Pipe is a 5/16 UNF threaded stud that secures the exhaust manifold outlet flange to the front pipe in the exhaust ...

Valve Guide A precision sleeve pressed into the cylinder head that supports and locates the inlet valve stem, holding the valve concentric with its...

Exhaust Valve Guide is pressed into the cylinder head to support and align the exhaust valve. It locates the valve stem so the valve seats squarel...

Inlet Valve Guide for the diesel cylinder head, part of the valve train. Pressed into the cylinder head, the guide locates the inlet valve stem an...

Track Rod & Steering Damper Bush for the steering linkage, locating the steering damper at its mounting eye. The bush insulates the damper mou...

Trunnion

Suspension Spring U-Bolt for the front leaf-spring suspension, clamping the axle to the spring pack. The U-bolt wraps around the front axle tube a...

Heater Hose for the rear of the heater circuit, carrying engine coolant between the heater pipe and the heater unit. This flat-section hose forms ...

Heater Hose for the front of the heater circuit, carrying engine coolant between the engine feed and the heater unit. This flat-section hose forms...

Brake master cylinder (single line with servo)

Brake Master Cylinder is the hydraulic control unit of the braking system, generating the fluid pressure that actuates the wheel cylinders at each ...

Chassis Bush - 88in - Front is a rubber bush that fits the rear mounting point of the front leaf spring, locating the spring in the chassis-side sh...

Chassis Bush - 88in - Front is a rubber bush that fits the rear mounting point of the front leaf spring, locating the spring in the chassis-side sh...

Radiator Hose - Top - 2.25 Petrol is the upper coolant hose connecting the thermostat housing outlet to the inlet of the radiator header tank in th...

Bottom radiator hose SII(A) 2.25

Bulb rated 12V 4W with a small-diameter fitting, part of the vehicle lighting system. This low-wattage bulb suits the small-fitting (Lucas-type) l...

Gearbox Front Cover Oil Seal for the manual gearbox front cover, sealing around the primary (input) shaft. Retains gearbox oil and excludes dirt a...

Thrust Bearing for second and third gears in the LT95 four-speed gearbox. This flat Torrington needle roller bearing seats against the 2nd and 3rd...

Gasket gearbox front cover and oil pump. LT95 4-speed gearbox - Early 110 V8, - S3 109" stage 1 V8, - 101" F.C. - Early Range Rover Classic

Clutch Fork Insert is the nylon insulator that fits over the clutch fork pivot pin inside the bellhousing, cushioning the fork at its fulcrum point...

Clutch Lever Clip that retains the clutch release lever on its pivot post within the gearbox bellhousing. The clip holds the release fork onto the...

Oil Seal for the front output shaft of the LT95 gearbox, sealing the transfer case around the rotating output shaft. The LT95 is a combined main g...

Drive Member - 10-Spline is the drive coupling at the outer end of the axle, forming part of the wheel hub and drive assembly. Its 10-spline inter...

Driving Member is the front hub drive flange that couples the axle halfshaft to the road wheel hub. It bolts to the outer face of the front hub, w...

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...

Drive Flange Joint Washer is the sealing washer installed at the joint between the drive flange and the stub axle, preventing differential oil from...

thrust collar, bush for stub axle - RRclassic upto (VIN) HA610293, - 101" Forward Control.