Products

Half Shaft – Rear LH – 10-Spline is the rear axle drive shaft for the left-hand side. It transmits drive from the differential out to the rear hub ...

Reverse Shaft for the Series III 4-speed gearbox, Suffix A build. This shaft carries the reverse idler gear within the gearbox casing. It fits the...

Brake Drum - 10 Inch for the wheel brake assembly on early short wheelbase Series Land Rovers. Fits the 10-inch drum brake system used on SWB (88"...

Clutch Plate is the friction-lined driven plate of the clutch assembly, 9 inch (229 mm) diameter. Its splined hub engages the gearbox input shaft ...

Clutch Cover is the pressure plate assembly of the clutch, 9 inch (229 mm) diameter, coil-spring type with three release fingers. It bolts to the ...

Clutch Release Plate for the LT77 5-speed manual gearbox clutch release assembly. This mounting plate fastens the external hydraulic clutch slave ...

U-Bolt – Rear – 1-Ton clamps the rear leaf spring to the axle. The U-shaped bolt passes over the axle and through the spring seat plate, where its ...

Exhaust clamp rubber strap

Mainshaft Bearing

Bottom cover seal

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Hexagon Nut with a 7/16" BSF (British Standard Fine) thread. A standard nut cut to the British Standard Fine thread form used throughout the fixin...

Intermediate Gear Shaft for the transfer gearbox. The shaft carries the intermediate gear that transmits drive from the gearbox mainshaft to the fr...

Bearing needle roller

Heater Hose carries engine coolant between the valve and the heater tap, forming part of the heater coolant circuit that feeds the heater matrix. ...

Heater Hose - Series 3 RHD

Heater Hose connects the cylinder head heater outlet into the heater coolant circuit, carrying hot coolant from the engine toward the heater matrix...

Thermostat - the coolant-flow control valve in the engine cooling system, with an 82°C opening temperature. Mounted in the thermostat housing at t...

Thermostat - the coolant-flow control valve in the engine cooling system, with an 82°C opening temperature. Mounted in the thermostat housing at t...

Handbrake Return Spring is part of the transmission-mounted drum-type handbrake, acting on the relay lever within the parking brake mechanism. Whe...

Core Plug (cup/expansion plug) seals a casting core hole in the cylinder block, fitted at the rear of the block. It closes the openings left by th...

Oil filler cap

Exhaust Manifold bolts to the exhaust ports on the cylinder head and collects the exhaust gases from the cylinders into a single outlet feeding the...

Exhaust Silencer sits in the rear section of the exhaust system, downstream of the intermediate pipe and ahead of the tailpipe outlet, where it for...

Exhaust Silencer - Stainless sits in the rear section of the exhaust system, downstream of the intermediate pipe and ahead of the tailpipe outlet, ...

Axle Check Strap limits the downward travel of the rear axle, fitted within the rear suspension on the 1-Ton chassis running the Salisbury axle. I...

Accelerator Cable links the accelerator pedal to the injection pump throttle lever, forming part of the throttle linkage on the 2.25L diesel engine...

Check strap 109"" 88cm long

Past op alle benzine en diesel 109"" modellen (knevel sluiting)

cable choke S3 - Right Hand Drive 2.25L 4-cylinder petrol fitted with steering column lock, - Left Hand Drive 2.6L 6-cylinder petrol fitted with s...

Choke Cable is the manual choke control cable in the carburettor fuel system, running from the dashboard choke knob to the carburettor choke lever....

Choke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...

Choke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...

Stop Cable Diesel Without Steering Column Lock RHD

Engine Stop Cable for the fuel shut-off control of the 2.25L diesel engine. Operating within the fuel injection circuit, the cable links the dashb...

Exhaust silencer and tailpipe LWB

PDWA valve

Rear Halfshaft for the Rover-type rear axle, right-hand side. The halfshaft transmits drive from the differential through the axle casing to the r...

Distance piece

Fitment: All models to 1980 except V8

Rear Axle Stub for the rear axle assembly on early Series Land Rovers. The axle stub is the outboard section of the rear axle shaft assembly, carr...

Needle Roller Bearing for the transfer box intermediate gear. The bearing carries the intermediate gear on its shaft within the gear cluster, allo...

Wheel Cylinder - LH Front for the front drum brake assembly on long wheelbase Series models. This hydraulic wheel cylinder is mounted at the left-...

Wheel Cylinder - RH Front for the front drum brake assembly on long wheelbase Series models. This hydraulic wheel cylinder is mounted at the right...

Wheel Brake Cylinder Overhaul Kit for the drum brake hydraulic circuit. This kit provides the renewable seal components required to overhaul the f...

Flywheel for the 2.25L petrol engine in its 3-main-bearing configuration. Bolted to the rear flange of the crankshaft, the flywheel stores rotatio...

Gearbox Gasket Kit - No Seals for the 4-speed manual gearbox and transfer box on Series models. This set supplies the paper and fibre mating gaske...

Propshaft Yoke for the propshaft flange joint, part of the Drivetrain assembly. This flange yoke bolts to the transfer case or axle flange and acc...