Products

Chassis Shackle Bush – Front is the compliant bush at the chassis end of the front spring shackle, part of the leaf spring suspension mounting. Th...

Chassis Shackle Bush – Front – Polyurethane is a set of four polyurethane bushes for the chassis end of the front spring shackles, part of the leaf...

Brake master cylinder LWB post-80

Spring Shackle connecting the end of a leaf spring to the chassis bracket, allowing the spring to lengthen and shorten as it deflects under load. ...

Shackle Plate, the side plate of the spring shackle assembly that forms the swinging link between the leaf spring eye and the chassis shackle brack...

Front Shackle Plate forms part of the front leaf-spring shackle assembly, connecting the road spring eye to the chassis mounting. The shackle allow...

Front Shackle Plate forms part of the front leaf-spring shackle assembly, connecting the road spring eye to the chassis mounting. The shackle allow...

Woodruff Key that locates the timing gear and pulley on the crankshaft of the Rover V8 petrol engine. The key sits in the crankshaft keyway to pos...

Folding side step Series

Pinion Lock Nut – Salisbury secures the drive pinion in the Salisbury rear differential, retaining the pinion flange and holding the pinion bearing...

Oil Seal – Rear Output Shaft seals the rear output shaft of the LT95 combined gearbox and transfer box, preventing oil leakage where the shaft exit...

Speedometer Drive Cable transmits rotational drive from the gearbox speedometer take-off to the speedometer head in the instrument panel. An inner...

Front Exhaust Pipe - downpipe section of the exhaust system. Connects the exhaust manifold to the intermediate pipe and silencer, carrying exhaust...

Steering Relay Gasket seals the steering relay assembly within the steering linkage. The steering relay transfers movement from the steering box d...

Gasket A large gasket for the 2.0L four-cylinder petrol engine. It forms a sealed joint between two mating engine components to prevent the leakag...

Circlip

Brush set M418G

Accelerator Rod Ball Joint forms an articulated pivot in the accelerator (throttle) control linkage, joining adjacent sections of the accelerator r...

Carb overhaul kit 175CD V8 Zenith Stromberg

Sedimentor Seal for the diesel fuel sedimentor assembly. The sedimentor separates water and sediment from the fuel ahead of the injection system. ...

Sedimentor Sealing Ring for the diesel fuel filter and sedimentor assembly. The sedimentor separates water and sediment from the diesel fuel befor...

Self-Tapping Screw - a No. 8 x 3/8" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as it ...

Self-Tapping Screw – No. 8 × 5/8 in is a general-purpose fastener for securing body, trim and panel fixings. Being self-tapping, it forms its own ...

Tap screw

Drive Screw - a No. 6 x 1/2" self-tapping drive screw used across door and facia assemblies. It secures the front door glass and window regulator,...

Seat belt bracket RH

Camshaft Bearing Kit

Reservoir kit

Brake Master Cylinder Repair Kit for the dual-line (split-circuit) braking system with direct-acting servo. This is a seal/overhaul kit that recon...

Volume Control Screw for the Zenith 36 IV carburettor. This spring-loaded idle mixture screw adjusts the volume of the idle circuit, setting the ai...

Pinion Seal - Salisbury Axle seals the nose of the pinion shaft at the front of the Salisbury differential housing, where the propshaft coupling fl...

Designed for Land Rover Series 2, 2A, and 3 (2.25 Petrol) Includes slotted shaft for compatibility with early-type fuel pumps Restores proper ...

Tub Floor Reinforcement Crossmember is a structural member in the rear body, supporting the load floor of the rear tub. It runs across the undersi...

Restore and reinforce your Land Rover's rear floor structure with this galvanised body crossmember floor, designed for Defender and Series 2, 2A, a...

seal washer for block coolant drain plug. - All 4-cylinder engines upto 1998 (except VM diesel)

Joint Washer - a sealing washer for the piston-cooling oil squirt jet in the engine lubrication circuit. It seals the oil spray jet where it meets...

Hinge Bonnet - 90/110

Spire Clip used to retain front wing panels and heater assembly components. This spring-steel clip slides over a screw or stud thread and grips se...

Support Bracket for the upper rear body section, forming part of the rear body-to-chassis structure. It locates and supports the upper rear body p...

Plate grommet GENUINE LR

Direction Indicator Lamp is a rear amber turn-signal lamp to NAS (North American Specification) pattern in the 95mm round format. It is supplied a...

Fuel Tank Sender Locking Ring for the fuel tank sender unit assembly. This ring secures the fuel level sender unit in position within the fuel tan...

Special Fixing Washer for the hardtop side-frame mounting. Seats over the M8 side-frame mounting stud and under its securing nut, spreading the cl...

Mounting Stud is a threaded fixing used in the rear body upper fixings. It is an M8 stud, 67 mm in length, providing a fixed threaded mounting poi...

Rear Lamp Guards - a pair of slatted steel guards fitted over the rear lamp assemblies to protect the lenses and lamp bodies from stone chips, bran...

Spare Wheel Cover fits over an externally mounted spare wheel to protect the tyre and wheel from weather, road dirt and UV exposure. This is the h...