Products

Battery Isolator Switch - key-operated master cut-off switch for the vehicle electrical system, rated at 300A. Wired inline on the main battery le...

Cup Holder for the BA 189A centre cubby box. This is the replacement cup holder component for the current-design cubby box, providing a secured rec...

Brake Pad Set for the BA 2165 front disc brake conversion. These are the replacement friction pads that fit the calipers used in the conversion, cl...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Upgrade your Land Rover Defender or Series vehicle with this complete 73mm LED Light Upgrade Kit. Designed to replace traditional incandescent lamp...

Shim hinge

Voltage Regulator (control box) of the screw-terminal type, for dynamo charging systems. The control box is wired between the dynamo and the batte...

set screw M6 x 25mm 8.8 various applications

Bolt - M6 metric thread, 70 mm long. A threaded fastener for securing components at a bolted joint. Tightened to the torque specified for the asse...

Bolt - M8 x 100mm hex head bolt used in the transmission mounting assembly. Secures transmission mounting components on Series III vehicles equipp...

Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing appli...

High-Tensile Hexagon-Head Bolt - an imperial 7/16" UNF fixing bolt, 2-1/2" long, in high-tensile grade. A general-purpose hex-head fastener with a...

Panhard Rod Bolt with a 1/2" UNF (Unified National Fine) imperial thread and a 3-1/4" shank length, manufactured to a high-tensile grade. Secures ...

Clutch Slave Cylinder Repair Kit for the hydraulic clutch release circuit on V8 petrol applications. The clutch slave cylinder is actuated by hydr...

Steel Ball - 9/32 inch steel ball used in the steering column assembly. Supplied individually. Ball diameter 9/32 inch (7.14 mm).

Gearbox Selector Ball is a hardened steel detent ball used in the manual transmission gear-selection mechanism. Spring-loaded against the selector...

Firtree Clip - a push-in fastener with a ribbed, fir-tree profile that grips into a pre-drilled panel hole. Used to secure trim panels, wiring loo...

LED Light Kit - 73mm

Connecting Rod Bolt for the big-end of the connecting rod, part of the crankshaft and connecting rod assembly. The bolt clamps the big-end bearing...

Screw securing the brake pedal bracket mounting plate within the pedal box. It fixes the pedal bracket plate in position, retaining the brake peda...

Differential Shim, 0.074in, used during differential build to set bearing preload and gear alignment. It sits against the differential carrier sid...

Outer Wing is the left-hand front wing outer skin panel, moulded in ABS plastic. It forms the visible outer surface of the front wing, covering th...

Front Wing Panel is the outer body panel covering the front wheel arch on the left-hand side, incorporating the headlamp aperture. Supplied as the...

Handbrake Tension Spring - the lower spring within the transmission (drum) handbrake assembly, fitted to vehicles with the LT95 four-speed gearbox....

Primary Pinion Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox (V8) casing. 2.10 mm thick, it controls p...

T-piece imperial

Heater Distribution Control Cable - the Bowden cable that links the dashboard heater control to the air-distribution flap in the heater assembly. ...

Water Pump Seal for the engine cooling circuit, sealing the water pump on four- and six-cylinder engines. The rubber seal seats the water pump aga...

Timing Chain Tensioner maintains correct tension on the timing chain of the 2.6L 6-cylinder petrol engine. Acting against the chain run, it takes ...

Circlip Retaining circlip for the gearbox rear output shaft. It seats in a machined groove on the output shaft, locating the adjacent component ax...

Glazing rubber

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

Hose Clip - Jubilee - 70-92mm is a worm-drive band clamp with a clamping range of 70-92 mm. It secures a hose over its spigot or connector, compre...

Brake Pipe Clip - single-bore retaining clip for securing a rigid brake pipe to the chassis or body structure. This clip holds the brake pipe in i...

Brake Union Nut - Metric Thread for the hydraulic brake pipe circuit. This union nut seals and secures brake pipe connections at the unions throug...

Glow Plug for the 2.25L diesel engine running a parallel (converted) glow plug system. Part of the cold-start pre-heating circuit. The glow plug h...

Bonnet Hinge Bolt Kit - a set of stainless steel fixings for mounting the bonnet hinges that allow the bonnet to pivot open. The kit secures the h...

Rear Crossmember Bolt Kit - a set of stainless steel fixings for securing the rear crossmember to the chassis. The rear crossmember is the rearmos...