Products

Inner Pinion Bearing for the Land Rover Series axle differential, supporting the pinion shaft at the inboard (crown wheel) end within the different...

Gear Lever Housing The ball/socket housing for the main gear lever, mounted on the gearbox top cover (turret). It seats the spherical lower end of...

Gear Lever Retaining Spring The spring that retains the main gear lever in its ball housing on the gearbox top cover. It bears down on the lever's...

Circlip - Gear Lever Spring Retention for the Series Land Rover gearbox gear lever assembly. This circlip retains the spring, retaining plate and ...

Joint Washer for the transfer gearbox top cover. This gasket seals the joint between the top cover and the transfer box housing, preventing oil le...

Gearbox Reverse Stop Spring for the gear selector mechanism. The spring acts on the reverse stop plunger, providing the resistance the gear lever ...

Drive Member Joint Washer - a sealing gasket fitted between the drive flange and the outer hub on Land Rover Series solid axles. This gasket seals...

Swivel Pin Housing Gasket for the front axle swivel assembly. This gasket seals the mating face between the chrome swivel ball housing and the fro...

Instrument Bulb - 12V 2.2W for the instrument panel. Replacement dial illumination bulb for the speedometer on Range Rover Classic Police Vehicle ...

Transfer Lever Knob in yellow, for the four-wheel-drive engagement lever on the transfer gearbox. It threads onto the top of the selector lever an...

Grommet seals and protects cables, harnesses and hoses where they pass through body and chassis panels. It is used at wiring harness pass-throughs...

Valve Stem Seal for the IOE (inlet-over-exhaust) engine valvetrain. Fitted over the valve stem at the top of the valve guide, it closes the cleara...

Grease Nipple with a short thread, used at propshaft universal joint lubrication points. The nipple threads into the grease point and provides the...

Front Brake Shoe Spring for the front drum brake assembly. This return spring connects the two brake shoes and pulls them back off the drum when th...

Drain Plug for the axle casing and fuel tank. This brass threaded plug seals the drain aperture at the bottom of the differential and axle casing,...

Swivel Ball Seal Retainer for the front axle swivel housing. This retaining ring clamps the swivel housing oil seal against the swivel ball, holdi...

Timing Chain Idler Wheel runs against the timing chain within the front timing case, guiding the chain and helping maintain its tension between the...

Drain plug

Gearbox Mainshaft Oil Seal for the rear of the manual gearbox, sealing the mainshaft where it passes through the rear of the mainshaft-and-gears se...

Differential flange 4-spline

Rear Shackle Pin for the rear leaf spring shackle. The pin secures the spring shackle at the rear mounting of the rear leaf spring, allowing the s...

Brake Shoe Anchor Plate for the rear drum brake assembly. The anchor plate provides the fixed abutment and locating point for the brake shoes. It ...

Lock Plate for the rear drum brake shoe retainer. This fold-over tab plate locks the two screws that secure the brake shoe bottom retainer ring. I...

Check Strap for the rear suspension assembly. The check strap limits the downward travel of the axle on droop, preventing the leaf springs from ove...

Bolt - 5/16 inch BSF x 1 inch for the gearbox selector assembly. Used to secure the gear selector forks to their respective selector shafts within...

Bolt - 3/8" BSF x 1" hexagonal head bolt to British Standard Fine thread specification. 3/8" BSF (British Standard Fine) thread with a 1" shank le...

Layshaft Split Ring Halves are a matched pair of semi-circular retaining ring halves used in the Land Rover Series I and II gearbox assembly. The ...

Split Pin locks slotted nuts, clevis pins and linkage joints against loosening, passing through a drilled hole and splayed to retain the assembly. ...

Exhaust Clamp Plate for the exhaust mounting assembly. Three-hole clamping plate that secures the exhaust pipe within the mounting bracket assembl...

Exhaust Bracket for the exhaust system on left-hand drive vehicles. This bracket supports and locates the exhaust along its run beneath the vehicl...

Exhaust Clamp for the exhaust-to-chassis mounting. Two-bolt upper clamp plate that forms the exhaust-to-chassis mounting assembly on Series and ea...

Exhaust Bracket for the exhaust system on left-hand drive vehicles. This bracket supports and locates the exhaust along its run beneath the vehicl...

Exhaust Saddle Clamp for securing exhaust pipe sections to underbody mounting brackets in the exhaust system. The U-shaped saddle body seats over ...

Clutch Anchor Plate - a steel mounting plate within the clutch pedal box assembly. It anchors the clutch pedal pivot to the bulkhead, providing th...

Axle Bump Stop - rubber bump stop for the front and rear suspension axle assemblies. Fitted to the chassis above each axle, the bump stop limits a...

U-Bolt - a rear leaf-spring axle clamp. It passes around the axle tube and clamps the rear leaf spring to the axle seat via the lower spring plate...

Front Towing Eye / Lifting Ring bolts to the front of the chassis, providing an anchored attachment point for towing, recovery and lifting. The ri...

Stub Shaft with a 10-spline drive coupling, a component of the axle half-shaft assembly. The stub shaft sits within the axle and transmits drive t...

Propshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...

Plain Washer - the upper mounting washer for the shock absorber. It seats over the top shock absorber mounting stud beneath the retaining nut, spr...

Front Spring Dowel for the 9-leaf front road spring, part of the leaf spring suspension assembly. The dowel is the centre locating pin that passes...

Wheel Cylinder for the drum brake assembly - the right-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either...

Wheel Cylinder for the drum brake assembly - the left-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either ...

Wheel Cylinder for the rear drum brake assembly, right-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hy...

Wheel Cylinder for the rear drum brake assembly, left-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hyd...

Spring Clip - a retaining clip in the transfer gearbox selector linkage. It secures the transfer lever to its pivot, holding the gear-change lever...

Front left-hand wheel cylinder for the hydraulic front braking system, installed within the brake backplate assembly of 11-inch front brake configu...