Products

Front brake wheel cylinder designed for use on Land Rover Series I, Series II, and Series III models. This component forms part of the hydraulic dr...

Copper Joint Washer for sealing fluid-carrying connections in the engine and cooling system. The annealed copper construction deforms under clampin...

Lamp Guard Distance Piece - spacer for lamp guard mounting hardware. The distance piece fits between the lamp guard frame and the light body or mo...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Outer Distance Piece for the front axle swivel pin housing. The distance piece is a spacer that sets the position of the swivel pin bearing within...

Rear Shackle Plate, part of the rear leaf spring mounting in the suspension assembly. The shackle plate forms one side of the spring shackle, link...

Exhaust Connecting Pipe is the intermediate section of the exhaust system for Series short wheelbase vehicles fitted with the 2.25L diesel engine, ...

Oil Pump Lock Tab, part of the engine oil pump assembly. The lock tab is a tab washer fitted under the oil pump retaining fastener; once the faste...

Gear - 2nd - Pair for the Series Land Rover four-speed main gearbox. This pair comprises the matched 2nd speed gears for both the mainshaft and th...

Flywheel Housing O-Ring - a sealing ring at the rear of the engine where the flywheel housing meets the cylinder block. Fitted to the 2.25L engine...

Cylinder Head Bolt - a clamping bolt securing the cylinder head to the engine block. It draws the head down onto the block to compress the head ga...

Domed Nut with a 5/16 UNF thread, a finishing fastener. The domed (acorn) form encloses the end of the stud or bolt it threads onto, protecting th...

Oil Gallery Plug for the cylinder block oil gallery on Land Rover 4-cylinder engines. The oil gallery is the network of internal drillings in the ...

Manifold Stud - a mounting stud for the manifold. Threaded into the cylinder head, it locates the manifold and clamps it to the head face via its ...

Flywheel Housing Stud - a mounting stud at the flywheel housing. Threaded into the housing, it provides the fixed stud onto which the mating compo...

Copper Injector Sealing Washer in the fuel injection assembly of pre-TDi Land Rover diesel engines. This copper washer seats beneath the injector ...

Valve Stem Oil Seal fits over the inlet valve stems to limit oil consumption past the valve guides in the cylinder head. It is used on 2.25L petrol...

Small End Bush (gudgeon pin bush) for the connecting rod small end on Land Rover diesel engines. The small end bush is a precision bronze bush pre...

Rocker Shaft Bush in the cylinder head valvetrain. The bush is pressed into a rocker pedestal and provides the bearing surface that supports the r...

Lock Washer secures a threaded fastener against loosening under vibration and thermal cycling. Fitted beneath the nut or bolt head, it bites into ...

Camshaft for the 2.25L 4-cylinder petrol engine valve train. Running in the cylinder block and driven from the crankshaft by the timing gear, the ...

Timing Cover Mudshield is the pressed shield that fits over the timing cover at the front of the engine. It screens the timing case and front pull...

Manifold Gasket - inlet to exhaust manifold gasket for the 2.25L 4-cylinder petrol engine. On this engine, the inlet and exhaust manifolds bolt to...

Thermostat Housing Gasket in the engine cooling system. This gasket seals the thermostat housing to its mating surface on the engine, preventing c...

Water Pump Impeller in the engine cooling circuit. Pressed onto the water pump spindle and driven by the fan belt, the impeller circulates coolant...

Water Pump Gasket sealing the water pump to the engine in the cooling circuit. The 8-hole gasket matches the bolt pattern of the water pump mounti...

Heater Plug Lead in the diesel glow plug pre-heat circuit. This 10" interconnecting lead links the No.2 and No.3 heater (glow) plugs, carrying cur...

Glow Plug Lead in the diesel glow plug (heater plug) pre-heat circuit. This short 5" lead interconnects glow plugs wired in series and is not inte...

Bolt securing the gearbox to the transfer box in the drivetrain. This fixing clamps the main gearbox housing to the transfer box. It applies to th...

Lock Nut with a 5/16" BSF thread. The lock nut secures a threaded fastening against loosening under vibration, maintaining clamp load in service. ...

Lock nut 3/8" BSF

U-Bolt Nut - 7/16 BSF for use in the leaf spring suspension assembly. U-bolts clamp the leaf spring pack to the axle casing at the front and rear ...

Nyloc Nut - 9/16" UNF for use in the leaf spring suspension assembly. This self-locking nut secures the shackle pin at the rear leaf spring shackl...

Screw - 10 UNF x 3/8 is a fixing in No.10 UNF (Unified National Fine) thread, 3/8 inch in length, used in fascia and dash assembly applications. Fi...

Starter Brush Set A set of replacement carbon brushes for the starter motor, part of the engine starting circuit. The brushes bear on the commutat...

Gasket

Steering Box Joint Washer - 0.005" selective shim washer used within the steering box. Fitted at the steering box joint face, this shim sets the c...

Layshaft Sleeve - bearing sleeve fitted to the layshaft (countershaft) in the LT67 main gearbox. Provides the running surface for the layshaft clu...

Exhaust Bracket Saddle Clamp for the intermediate exhaust pipe on 109-inch wheelbase Series 2 and Series 3 Land Rovers. The saddle clamp locates an...

Wheel Cylinder Overhaul Kit for front drum brake systems fitted with 11-inch brake drums. This kit provides the necessary parts to overhaul all fo...

Wheel Cylinder Repair Kit A seal repair kit for overhauling the rear brake wheel cylinders, part of the drum braking system. The wheel cylinder si...

Clutch Slave Cylinder for the hydraulic clutch actuation system. Mounted on the gearbox bellhousing, this cylinder receives hydraulic pressure fro...

Transfer Box Sealing Ring - Locking Pin A rubber O-ring that seals the locking pin where it enters the transfer box case. It seals the selector lo...

Spring - Timing Ratchet sits within the engine timing assembly on Land Rover 2.25L and 2.0L diesel engines. This spring provides the retention for...

Thrust Washer - 0.128" A gearbox mainshaft thrust washer for the second-speed gear, 0.128" thick. It controls the end-float of the 2nd-speed gear ...

Sump Gasket seals the joint between the oil sump and the cylinder block within the engine lubrication system, preventing oil leakage at the sump fl...