Products

Bonnet Canvas Rest Strip for the front body assembly. This canvas strip mounts across the top of the radiator/front panel, forming the surface the ...

Cleat Rope Hook Body Side All and Classic (Softtop) - Series Defender

Gear Lever Gaiter for the transmission tunnel. This flexible boot fits around the base of the gear lever where it passes through the tunnel, sealin...

Weatherstrip for the alpine light (side roof window) glass. This rubber sealing strip retains and seals the 5mm glass panels of the alpine lights ...

Gaiter Retainer - secures the rubber gaiter around the high-low (transfer) lever on the LT76 gearbox, which carries an integral transfer box. The ...

Tailgate Seal for the lower edge of the rear tailboard. It seats along the bottom of the drop-down tailgate and seals against the body, keeping wa...

Hoodstick Bracket Clamp - secures a hoodstick to its mounting bracket within the soft-top frame. The clamp holds the hoodstick (the soft-top frame...

Body Mounting Shim used to set the correct clearance and alignment between the body tub and the chassis mounting points. This thin flat shim is us...

Rear Quarter Seal - the rubber glazing seal that secures the fixed rear quarter window into the hard-top body aperture. Sized for 5mm glass, it be...

Interior Grab Handle - interior pull handle for the rear side door, used to draw the door closed from inside the cab. It fixes to the inner face o...

Door Clevis Pin for the door check strap mechanism. The pin locates the check strap to its mounting bracket, forming the pivot the strap works aga...

Spring Washer for the fuel tank sender unit and fuel pick-up pipe fixings. Fitted beneath the retaining screws that secure the fuel gauge sender u...

Floor Panel Screw with a mushroom head profile, used to secure floor plates and lower rear body panel assemblies on the Defender. The low-profile ...

Rear Mudflaps - a pair of rear mudflaps for the 88in short-wheelbase, fitted behind the rear wheels to deflect road spray and debris thrown up by t...

Front Mudflaps, supplied as a pair. The mudflaps mount behind the front wheels to deflect road spray, mud and stones thrown up by the tyres, prote...

Lower Tailgate for the rear of the body - the drop-down tailboard panel that closes off the rear of the load area. Hinged along its lower edge, it...

Barrel Lock and Key, Set of Two for the door locks, supplied as two keyed lock barrels each with a key. Each barrel is the cylinder the key turns ...

Barrel Lock and Key, Set of Three for the door locks, supplied as three keyed lock barrels each with a key. Each barrel is the cylinder the key tu...

Bench Seat Backrest in black vinyl, forming the upright back section of the folding rear load area bench seat. This 810mm wide backrest mounts to ...

Bench Seat Backrest in techno fabric, forming the upright back section of the folding rear load area bench seat. This 810mm wide backrest mounts t...

Front Outer Seat Cushion Base for the adjustable seat frame in Series II, IIA, and III 109" long-wheelbase vehicles. This is the outer seat base c...

Inner Seat Base is the centre front seat base cushion, forming the lower seating platform of the basic vinyl front seat. Finished in black vinyl f...

Track Rod End (Right-Hand) is the ball-joint connector at the end of the steering track rod, linking the track rod to the steering arm. It transmi...

Track Rod End with left-hand thread, part of the steering linkage. The track rod end connects the track rod to the steering arm through a ball joi...

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Drain Plug - a tapered threaded plug used to seal and drain fluid from engine and driveline housings. It serves as a coolant drain plug in the cyl...

Front Floorplate - Right-Hand Side for the cab floor structure of Series II, IIA, and III Land Rovers. This pressed steel panel forms the right-ha...

Front Floorplate - Left-Hand Side for the cab floor structure of Series II, IIA, and III Land Rovers. This pressed steel panel forms the left-hand...

Upper Door Hinge for the right-hand door, forming the upper pivot of the door-to-body mounting. Fitted as the upper member of the door's two-hinge...

Door Cap (Galvanised, Right-Hand) is the capping rail that forms the top edge of the right-hand front door frame around the window aperture. The g...

Door Cap (Galvanised, Left-Hand) is the capping rail that forms the top edge of the left-hand front door frame around the window aperture. The gal...

Rubber Buffer for the door-top sliding side window. The buffer fits at the top of the door and acts as an end-stop for the sliding glass, limiting...

Door Top Seal Strip for the front door assembly. This rubber seal runs along the upper section of the door frame, sealing the gap between the door ...

Filler Strip for the door top. The strip fits along the top edge of the door, closing and finishing the joint at the door-top glass frame and seal...

Filler Strip Spacer for the door top, fitting at the vertical joint of the door-top glass frame. The strip fills and finishes the vertical gap in ...

Wing Stay for the rear body structure of the Series Land Rover. This right-hand steel bracket braces the rear wing to the body sill, providing str...

Sill Panel (5" Deep, Front, Right-Hand) is the lower body panel that runs along the right-hand front body side beneath the door aperture. It forms...

Sill Panel (5" Deep, Front, Left-Hand) is the lower body panel that runs along the left-hand front body side beneath the door aperture. It forms t...

Sill Panel (5" Deep, Rear, Right-Hand) is the lower body panel that runs along the right-hand rear body side beneath the rear body aperture. It fo...

Sill Panel (5" Deep, Rear, Left-Hand) is the lower body panel that runs along the left-hand rear body side beneath the rear body aperture. It form...

Handbrake Gaiter - round-hole type - for the transmission handbrake (parking brake) lever assembly. This rubber gaiter fits over the base of the L...

Tailgate Chain Cover - a pair of protective sleeves that fit over the two retaining chains supporting the rear tailgate. Each chain links the tail...

Wing Panel (Aluminium, Front Outer, Right-Hand) is the outer front body panel covering the right-hand front wheel arch. It forms the visible body ...

Front Outer Wing Panel - Aluminium - Left Hand Side for Series Land Rovers. This aluminium outer wing panel replaces the front left wing skin on S...

Front Mudshield - RHD - Left Hand Side for Series II and IIA Land Rovers. This inner panel sits between the front wing and the engine bay on the l...

Steering Box Cover for the steering box, for right-hand-drive (RHD) applications. The cover plate bolts onto the steering box housing, enclosing a...