Products

Steering Box Cover - LHD - inner wing mudshield for the steering box. This pressed cover fits over the steering box on the inner wing panel, shiel...

Hoodstick - front bow of the soft-top hood frame. This steel bow forms the front arch of the soft-top hood frame, providing structural support at ...

Hoodstick - the rearmost bow of the soft-top canvas roof framework on Land Rover Series and Defender vehicles. This hoodstick forms the rear struc...

Hook for the soft top retaining rope, part of the hood and hoodstick assembly. Secures the rope that runs along the soft top drain channels.

Front Rope Retaining Hook - Left Hand Side for the soft-top hood system on Series and Defender Land Rovers. This hook is part of the hoodstick and...

Bulkhead Vent Seal - rubber seal for the bulkhead fresh-air vent flap. This rubber seal fits around the bulkhead air vent aperture, sealing the hi...

Sliding Window Seal for the front door assembly. This rubber seal fits to the front face of the sliding side window, sealing the glass against the ...

Window Channel for the front door sliding side window assembly. This aluminium channel runs along the front face of the sliding window and retains...

Tie Tube - a side brace for the full-length soft-top hood frame assembly on long-wheelbase Land Rover vehicles. This tube provides lateral structu...

Hinge Pin Kit containing the replacement hardware for door and rear tailgate hinges on Series and early Defender models. Fits the front and rear d...

Hood Stick Kit - the framework of bows and sticks that forms the skeleton of a canvas soft top (tilt), carrying and tensioning the fabric over the ...

Canvas Hood in sand - a full-length soft top for the short-wheelbase (88") body. It fits over the hood stick frame and fastens along the body rail...

Stud

Rubber Mat - ribbed rubber loadspace mat for the rear floor of short wheelbase (88-inch) models. Measuring 1177 × 920 × 3mm, the mat covers the re...

Floor Mat Retainer secures the intermediate second-row rubber floor mat. Holds the mat in position against movement underfoot.

Leather hasp civilian

Tailgate Buffer - rubber buffer for the rear tailgate (tailboard). This rubber buffer cushions the tailgate where it meets the body, absorbing the...

Pillar seal

Window Seal - a rubber glazing seal that beds the window glass into its body aperture, sealing the joint against water and draughts.

Sliding Window Catch secures the sliding glass of the front door side window, locking the two panes together so the window can be held shut or fixe...

Tailgate Hook for the lower hinged tailboard, right-hand side. This pigtail (spiral) hook mounts on the body and retains the tailgate support stra...

Tailgate Hook for the lower hinged tailboard, left-hand side. This pigtail (spiral) hook mounts on the body and retains the tailboard chain, holdi...

Rear Wing Stay for the rear body assembly of Series II, IIA, and III Land Rovers (1958-1985). This stay bracket braces the rear wing against the b...

Fitment: all models to 1980

Floor Mounting Pad is a 5mm rubber spacer pad used at the rear body floor support mounting, fitted between the body and the chassis-mounted support...

Bonnet Buffer - rubber buffer at the bulkhead. This rubber buffer mounts at the bulkhead where the rear of the bonnet rests when closed, cushionin...

Hood Fixings - hood stick set for the full canvas hood on Long Wheelbase Series vehicles. Hood sticks are the metal bows that form the internal st...

Door Trim Retainer - lower horizontal retainer for the rear end door window. This retainer secures the lower edge of the glass within the rear end...

Glass Retainer is the vertical glazing retainer for the rear end door assembly. Holds the rear door glass along its vertical edge.

Door Trim Retainer - upper horizontal retainer for the rear end door window. This retainer secures the upper edge of the glass within the rear end...

Check rod RH

Door Seal fits along the floor line of the rear side door aperture, sealing the gap between the lower edge of the door and the body sill. It block...

Corner Capping - galvanised - right-hand (offside) roof corner. This galvanised steel capping fits over the offside rear roof corner, covering and...

Rubber Seal fits along the joint between the truck cab base and the rear body, sealing where the cab meets the tub. It forms a continuous barrier ...

Body Seal - a moulded rubber weather seal in the body & chassis assembly. It closes the gap between adjacent body panels to exclude water, dus...

Vent Lid Hinge Pin - hinge pin for the dash ventilator flap. This pin forms the pivot on which the dash fresh-air ventilator lid hinges, allowing ...

Grommet - rubber blanking grommet for the transmission (gearbox) tunnel cover. This rubber grommet seals the access aperture in the gearbox tunnel...

Turnbuckle is the semi-circular catch that fastens the seat box and rear tub locker lids down. It rotates over the mating hasp to hold the lid shu...

Window Channel - Front Door

Window Channel (bailey channel) for the sliding side window glazing assembly. It runs along the edge of the window aperture in the door frame, form...

Clevis Pin for the bonnet stay. Forms the pivot at the upper end of the bonnet prop, retaining the stay to the bonnet.

Bolt securing the bulkhead to the chassis outrigger. A 1/2" UNF hex-head bolt used at the lower bulkhead mounting points, where the bulkhead fixes...

Windscreen Glass - replacement glass panel for the windscreen frame. Fits the windscreen aperture as a direct replacement for cracked or damaged g...

Door Bottom for the left-hand side, forming the lower section of the door assembly. This is a repair panel that replaces the lower portion of the ...

Rear Sill Panel for the right-hand side, a body repair panel in the lower bodyside and chassis structure. The panel forms the rear section of the ...

Rear Sill Panel - Left Hand is a pressed steel body panel that forms the lower left-hand side of the rear body tub. The panel closes the gap betwe...

Front Sill Panel for the right-hand side, of the narrow sill type. The sill is the structural panel running along the lower edge of the body benea...

Front Sill Panel - Left Hand is a pressed steel body panel that forms the lower left-hand side of the front body section. The panel closes the low...