Products

Front Door Lock Set provides key-operated locking for the front doors and is of the anti-burst type, designed to resist the latch springing open un...

Door Bottom - RH is the lower repair section of the right-hand front door. It replaces the corroded or damaged bottom portion of the door frame, r...

Lower Door Panel forms the bottom half of the two-piece door assembly, for the Left Hand (LH) side. It is the lower structural panel of the door b...

Front Door Check Strap, part of the front door hinge and retention hardware. Connecting the front door to the body pillar, the check strap limits ...

Door Seal The lower front door seal for the right-hand door, sealing between the front door and the bulkhead. It forms the weather seal along the ...

Door Seal The lower front door seal for the left-hand door, sealing between the front door and the bulkhead. It forms the weather seal along the l...

Door Lock - Old Style - Button No Barrel - RH is the latching mechanism for the right-hand rear side door. This is the early (old-style) pattern, ...

Door Lock - Old Style - Button No Barrel - LH is the latching mechanism for the left-hand rear side door. This is the early (old-style) pattern, f...

Door Seal for the front door, rear lower section, right-hand side. Part of the door aperture weather-sealing. This rubber seal fits along the lowe...

Door Seal The lower rear door seal for the left-hand front door, sealing the lower rear edge of the door against the body. It forms part of the fr...

Door Seal for the front door, part of the door sealing system. Runs around the front door aperture to seal the gap between the door and the body s...

Door Seal - Front - Top is the weatherstrip that closes the joint between the top edge of the front door and the roof cant rail, forming part of th...

Door Seal A general-purpose door aperture weather seal, suited to the front doors, rear side doors and rear door/tailgate openings. It seals the g...

Nut A 4BA hex nut used as a threaded fastener. Applied on the door lock linkage and rear bumper mountings.

Differential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...

Clip

Pack piece

Fuel Tank Mounting is the moulded rubber isolator in the fuel tank mounting assembly that sits between the tank body and its chassis support. It c...

Stub Axle Gasket for the rear drive shaft assembly on Land Rover Series II, IIA, and III. This gasket seals the stub axle flange at the rear axle ...

Intermediate Exhaust Pipe - the centre section of the exhaust system, connecting the front down-pipe to the rear silencer. Routes exhaust gas rear...

Shim plate

Layshaft First Gear - the first-speed gear on the layshaft (countershaft) of the main gearbox. Meshes with the corresponding mainshaft gear to pro...

Mainshaft Gear - 1st Speed is a 29-tooth first-speed gear that runs on the mainshaft within the manual gearbox gear train. As a non-synchronised c...

Flasher Unit is the 3-pin relay in the direction indicator circuit that switches the turn signal lamps on and off at a regular rate. Wired between...

Handbrake Catch Pawl, the ratchet claw of the transmission parking brake mechanism. It engages the toothed quadrant on the handbrake lever, lockin...

Instrument Panel Bulb, rated 12V 2W with a BA7s bayonet base (type 281), for the instrument cluster lighting circuit. It provides the internal ill...

Exhaust Connecting Pipe is the intermediate section of the exhaust system, joining the front pipe to the rear silencer. It carries exhaust gas alo...

Brake Shoe Spring for drum brake assemblies. This return spring draws the brake shoes away from the drum surface when the brake pedal is released,...

Brake & Clutch Reservoir Tank Kit, a replacement for the original single fluid reservoir that fed both the brake and clutch master cylinders. ...

Distance Piece - a machined spacer in the axle and suspension assembly, specified for the 1-Ton Military configuration. It sets the standoff betwe...

Fuel Cap closes and seals the fuel tank filler neck on petrol applications. It uses a two-lug bayonet fixing that locates and locks into the fille...

Fuel Cap Locking Hasp is the body-mounted latch in the fuel filler arrangement that secures the petrol filler cap against unauthorised opening. It...

Headlamp bulb 12V 40/45W duplo (non-halogen)

Fuel Filler Cap Seal is the sealing ring fitted inside the metal fuel filler cap. It forms the seal between the cap and the filler neck, preventin...

Self-Locking Nut, 3/8" BSF, used to secure propshaft fasteners within the drivetrain. The deformed thread form provides a self-locking action that...

Exhaust Downpipe is the front section of the exhaust system, connecting the exhaust manifold outlet to the intermediate pipe. This downpipe fits L...

Rocker cover rubber washer petrol

Flywheel Ring Gear for four-cylinder petrol engines. The ring gear is shrink-fitted to the periphery of the flywheel and meshes with the starter mo...

Tappet Screw - the valve-clearance adjusting screw in the rocker gear of the four-cylinder engine (3-bearing crankshaft), part of the valvetrain. ...

Tappet kit

Swivel Pin Housing Locking Plate mounts to the front axle swivel pin housing. It locks the swivel pin in position and provides the fixed stop that...

Bolt with a 3/8" UNF (Unified National Fine) thread and a 1-7/32" length. A standard imperial-thread fastener for chassis, driveline and body fixi...

Spring Shackle Distance Tube for the rear leaf spring shackle assembly. This spacer tube sets the correct spacing between the shackle plates, maint...

Accelerator pedal pad S3

Bush - Accelerator Linkage is a small bearing bush fitted to the accelerator linkage assembly on the 2.6L 6-cylinder petrol engine used in Series I...

Gearbox Cover Plate Gasket for the LT76 gearbox. This rubber gasket seals the cover plate to the gearbox casing, sealing the joint against oil lea...