Products

Rotor Arm for the distributor ignition system. The rotor arm mounts on the top of the distributor shaft and turns with it. It picks up the high-te...

Window Motor for the left-hand front door, part of the electric window mechanism. The motor drives the window regulator through its gearbox to rai...

Window Motor for the right-hand front door, part of the electric window mechanism. The motor drives the window regulator through its gearbox to ra...

Water Pump for the 2.5L VM Turbo Diesel engine, part of the Engine Coolant Circulation Assembly. The pump circulates coolant continuously through ...

Heater Blower Motor & Fan assembly for the cabin heating and ventilation system. The motor drives the fan that draws air through the heater box...

Heater Motor Adaptor Lead for the heater blower motor and fan assembly. This wiring adaptor bridges the blower motor to the vehicle's existing heat...

Fuel Stop Solenoid for the 200 Tdi and 300 Tdi 2.5L turbo diesel engine, mounted on the fuel injection pump. Held open while energised through the...

Injector Pipe for the No.4 cylinder of the 2.5L 200TDi diesel engine. This rigid high-pressure steel pipe carries metered fuel from the injection p...

Shaft 90/110 RH 31/10

Half Shaft - LH (Left-Hand), part of the Rear Axle Drive Assembly on the Defender 90, 110, and 130. This half shaft transmits drive torque from th...

Front Brake Caliper is the right-hand front caliper of the disc braking system, for the vented-disc setup. It clamps the brake pads against the fr...

Front Brake Caliper is the left-hand front caliper of the disc braking system, for the vented-disc setup. It clamps the brake pads against the fro...

Wiper Blade with a pin (bayonet) fitting for attachment to the wiper arm. Part of the windscreen wiper assembly, the blade holds the rubber wiping...

Voor alle LT77 versnellingsbakken

Fuel Lift Pump for the 2.25-litre four-cylinder petrol engine, mounted on the side of the cylinder block and sitting in the fuel supply circuit bet...

Fitment: All non ABS models (VIN) JA032851 on to (axle) 38L03120B. 39L05552B. 42L00521B. 43L18579B All Models From (A)57L00001B To (A)57L05188B0

Rear Wiper Blade for the rear screen wiper assembly, clipping to the wiper arm to sweep the rear glass. Fits wide 7mm wiper arms only - suits the ...

Front Mudflap Kit for the body and chassis, supplied as a matched left- and right-hand pair. Fitted behind the front wheels, the flaps deflect roa...

Protect your Discovery 1 with this rear mudflap kit, designed for both left and right sides. These no-logo mudflaps offer effective protection from...

CV Joint - front axle constant velocity joint located in the swivel housing at the outer end of the front halfshaft. It transmits drive to the fron...

Mesh Dog Guard a partition panel that mounts against the full-height rear bulkhead to separate the cab from the load area. Fitted to the existing ...

Differential Cover for the Salisbury rear axle. The cover bolts to the rear face of the axle casing, enclosing the crown wheel and differential and...

Adjustable-Height Towing Bar a rear towing attachment that bolts to the chassis towing points and carries the tow ball or coupling. The drop plate...

Rear Light Guard Set for Defender models fitted with a rear-door-mounted spare wheel. The set comprises one square guard and one L-shaped guard, f...

Side Moulding is an exterior body trim strip for the 2-door body side. It runs along the side body panel to protect the paintwork from stone chips...

Front Mud Flap Kit for the front wheel arches, supplied complete with mounting brackets. The mud flaps hang behind the front wheels to reduce road...

Light Guard Set - protective guards for the rear lamp units, mounted on the rear wings. The guards fit over the rear lamp lenses and shield them a...

Front Mud Flap Kit, supplied as a left and right pair. Mounts behind the front wheel arches to reduce spray, mud, and stone throw from the front w...

Sealed Rivet for securing fixed side windows. This is a closed-end blind rivet: the sealed body prevents water passing through the rivet hole, keep...

Body Rivet - a mechanical fastener used within the body and panel assembly to join thin sheet metal, trim and stowage fittings. Nominal size 3/16"...

Rivet - a mechanical fastener used within the body and chassis assembly to join thin sheet metal and panel components. Nominal size 3/16" (4.8 mm)...

Front Hub Assembly, ABS configuration. Part of the front axle hub and bearing system. The hub locates the front wheel and carries it for rotation ...

Front axle drive flange designed to connect the drive shaft to the wheel hub assembly. The flange transmits rotational force from the half shaft ...

Wheel Hub Stud FRC5926 or RUF000020 for Defender 90 And 110, Discovery I and Range Rover Classic.

Stake nut RR3, RR4

Tow Bar - Pre 1998

Air Suspension Transfer Relief Valve - solenoid valve in the air suspension compressor and supply circuit, mounted at the supply reservoir. Contro...

Filter valve assy

Air Suspension Compressor Mounting - rubber isolator supporting the electronic air suspension compressor at its rear mounting point. The compresso...

Anti-Roll Bar Bush - a mounting bush in the rear suspension anti-roll (stabiliser) bar assembly. It clamps the rear anti-roll bar to the body, loc...

Anti-Roll Bar Bush for the front suspension, locating the front anti-roll (stabiliser) bar to the body. The bush clamps around the bar and allows ...