Products

Chassis Bush - 88in - Front is a rubber bush that fits the rear mounting point of the front leaf spring, locating the spring in the chassis-side sh...

Radiator Hose - Top - 2.25 Petrol is the upper coolant hose connecting the thermostat housing outlet to the inlet of the radiator header tank in th...

Bottom radiator hose SII(A) 2.25

Bulb rated 12V 4W with a small-diameter fitting, part of the vehicle lighting system. This low-wattage bulb suits the small-fitting (Lucas-type) l...

Gearbox Front Cover Oil Seal for the manual gearbox front cover, sealing around the primary (input) shaft. Retains gearbox oil and excludes dirt a...

Thrust Bearing for second and third gears in the LT95 four-speed gearbox. This flat Torrington needle roller bearing seats against the 2nd and 3rd...

Gasket gearbox front cover and oil pump. LT95 4-speed gearbox - Early 110 V8, - S3 109" stage 1 V8, - 101" F.C. - Early Range Rover Classic

Clutch Slave Cylinder Push Rod for V8 applications, part of the hydraulic clutch release circuit. The push rod transfers movement from the slave c...

Clutch Fork Insert is the nylon insulator that fits over the clutch fork pivot pin inside the bellhousing, cushioning the fork at its fulcrum point...

Clutch Lever Clip that retains the clutch release lever on its pivot post within the gearbox bellhousing. The clip holds the release fork onto the...

Oil Seal for the front output shaft of the LT95 gearbox, sealing the transfer case around the rotating output shaft. The LT95 is a combined main g...

Drive Member - 10-Spline is the drive coupling at the outer end of the axle, forming part of the wheel hub and drive assembly. Its 10-spline inter...

Gearchange Spring

O-Ring for the speedometer drive spindle on the LT230 transfer gearbox. Seals the spindle housing where the speedometer drive take-off enters the ...

Driving Member is the front hub drive flange that couples the axle halfshaft to the road wheel hub. It bolts to the outer face of the front hub, w...

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...

Swivel Pin Housing Shim (0.003in) used to set the swivel pin bearing preload on the front axle swivel assembly. The shim is fitted at the swivel p...

Swivel Pin Housing Shim - 0.005in is a 0.005 in (0.13 mm) shim used to set the bearing preload in the front axle swivel pin housing assembly. Fitt...

Swivel Pin Housing Shim - 0.010in is a 0.010 in (0.25 mm) shim used to set the bearing preload in the front axle swivel pin housing assembly. Fitt...

Swivel Pin Housing Shim used to set the swivel pin bearing preload on the front axle swivel assembly. The shim is fitted at the swivel pin to adju...

Drive Flange Joint Washer is the sealing washer installed at the joint between the drive flange and the stub axle, preventing differential oil from...

Upper Swivel Pin forming the upper pivot of the front axle swivel housing. The pin bolts to the top of the swivel pin housing and runs in the uppe...

Front Brake Disc for the front axle braking system. This is a solid (non-vented) disc with a diameter of 298 mm. It mounts to the front hub and pr...

Seal Washer - Swivel Pin Housing is the joint washer that seals the lower swivel pin mounting within the front axle swivel pin housing assembly. C...

Lower Swivel Pin forming the lower pivot of the front axle swivel housing. The pin bolts to the underside of the swivel pin housing and carries th...

thrust collar, bush for stub axle - RRclassic upto (VIN) HA610293, - 101" Forward Control.

Thrust Sleeve fits over the front axle half shaft within the constant velocity (CV) joint and swivel housing assembly. It locates between the CV j...

Gearbox Side Cover Gasket for the LT95 4-speed V8 gearbox. This gasket seals the side cover to the gearbox casing, preventing oil leaks from the ge...

4WD Selector Rod for the Series transfer box. It forms part of the four-wheel-drive engagement linkage, transmitting selector movement through the...

Gasket

Joint washer

Disc brake

Transfer Box Output Shaft Mud Shield fitted at the output shaft oil seal of the LT230 transfer box. The shield sits over the output shaft ahead of...

Rear Propshaft transmitting drive from the transfer box rear output to the rear axle differential. The shaft carries torque from the transfer box ...

Front Radius Arm Bush (rubber) located at the chassis end of the front radius arm. The bush is pressed into the radius arm mounting eye where the ...

Front Radius Arm Bushes in black polyurethane, supplied as a set of four for the chassis-side (rear) mounting of the front radius arms. The bushes...

Spring Retention Ring for the front coil-spring suspension. It clamps the upper end of the road spring, securing it against its seat on the chassis...

Exhaust Bush - Male is the male-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the cor...

Exhaust Bush - Female is the female-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the...

Mounting Link Bottom Range Rover Classic

Bottom link mounting RRC polyurethane pair

Radiator Mounting Bush is the rubber isolation bush that secures the radiator to the body or chassis mounting points, preventing direct metal-to-me...

Front Coil Spring, part of the front coil-sprung suspension. The spring fits between the chassis spring seat and the front axle, supporting vehicl...

Fuel Pump Adaptor for mounting the external fuel pump on petrol engines. It provides the interface between the external fuel pump and its mounting...

Instrument Panel Bulb - 12V 3W capless. A push-fit capless bulb for instrument cluster and panel illumination and for low-current warning and indi...