Products

Screw securing the brake pedal bracket mounting plate within the pedal box. It fixes the pedal bracket plate in position, retaining the brake peda...

Differential Shim, 0.074in, used during differential build to set bearing preload and gear alignment. It sits against the differential carrier sid...

Outer Wing is the left-hand front wing outer skin panel, moulded in ABS plastic. It forms the visible outer surface of the front wing, covering th...

Front Wing Panel is the outer body panel covering the front wheel arch on the left-hand side, incorporating the headlamp aperture. Supplied as the...

Handbrake Tension Spring - the lower spring within the transmission (drum) handbrake assembly, fitted to vehicles with the LT95 four-speed gearbox....

Primary Pinion Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox (V8) casing. 2.10 mm thick, it controls p...

Rivet used within the main wiring harness assembly to secure harness routing and retain protective coverings to body mounting points. Maintains st...

Camber Bush Set for the front radius arms, 38mm wide. The bushes locate in the front radius arm mountings and set the caster and camber geometry o...

Transfer Box Flange Bolt - a 3/8" UNF x 1-1/4" hex-head bolt for the LT230 transfer case front output flange. It secures the drive flange to the f...

Brake Front Disc - Steel Wheel Midget

Brake Front Disc - Wire Wheel Midget

Brake Front Disc Mgbgtv8

Brake Front Disc Mgb

T-piece imperial

Radiator Frame – Top, the upper section of the radiator mounting frame. The top frame retains and locates the upper edge of the radiator within th...

Radiator Frame – Bottom, the lower section of the radiator mounting frame. The bottom frame retains and locates the lower edge of the radiator wit...

Radiator with Integrated Oil Cooler - the main engine cooling radiator for the 200 TDi diesel engine, incorporating a built-in engine oil cooler an...

Radiator Core is a replacement copper cooling core for the 300 TDi radiator, supplied as the core only without the top and bottom tanks. It is int...

Gear Lever Gaiter - rubber gaiter fitting over the gear lever and transfer box lever at the transmission tunnel diaphragm panel, sealing the tunnel...

Heater Hose - the inlet hose in the heater coolant circuit on the V8 twin-carburettor petrol engine. It carries hot coolant from the engine to the...

Heater Inlet Hose is the coolant feed hose supplying the heater matrix in the cabin heating circuit. It carries hot coolant from the engine to the...

Heater Outlet Hose is the coolant return hose from the heater matrix in the cabin heating circuit. It carries coolant from the outlet side of the ...

Rear Mudflap - exterior splash guard that mounts behind the rear wheel to deflect mud, water and road debris away from the underbody and following ...

Rear Mudflap - exterior splash guard that mounts behind the rear wheel to deflect mud, water and road debris away from the underbody and following ...

Receiver Dryer for the air conditioning system, compatible with R134a refrigerant. Installed on the high-pressure side of the A/C circuit, between...

Heater Return Hose moulded coolant hose within the heater circuit, carrying coolant from the heater matrix back to the engine cooling system. Shap...

Front Grille - Horizontal for Range Rover Classic. This is the horizontal-slat style front radiator grille introduced with the 1987 facelift and u...

Mirror RR Manual

Seat Belt - Rear Centre Lap - Long End for the rear seat belt assembly in the Defender passenger compartment. This is the long webbing end of the ...

Mirror Glass - Exterior Door Mirror - Right Hand for the Range Rover P38 exterior mirror assembly. This is the replacement glass insert for the ri...

Mirror glass LH

Heater Hose - coolant return hose in the heater circuit for the 300 Tdi engine. It carries coolant on the return path from the heater matrix back ...