Products

Rubber Plug Cushion is a moulded rubber blanking plug that fits into a pre-formed aperture in the body, frame or seat base to close off the opening...

Floor Mat for the second seat row, a ribbed rubber mat protecting the intermediate floor area. Approximate dimensions 1490 x 460 x 3 mm.

Female Dovetail for the rear end door latch mechanism. Receives the male dovetail to align and secure the rear door as it closes. Sold individually.

Spacer

Filler Strip is the fixing channel that runs along the top edge of the rear door window aperture. It locates and retains the upper edge of the doo...

Clip - a retaining clip within the vehicle body hardware, used to secure and locate a fitted component in position.

Centre Retainer - Front Windscreen Glass is the metal retainer strip that secures the front windscreen glass at its centre division point. The ret...

Blanking Plug for closing an unused 13 mm (1/2") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Rubber Washer - Seat Backrest for Land Rover Series and Defender models. This rubber washer is used in the seat backrest assembly, fitting beneath...

Hook

Retainer - LH

Hose Clip Spring is the spring connector clip for the heater demister and air outlet pipes. Retains the demister ducting and outlet flaps within t...

Spare Wheel Bracket is the mounting bracket for a side-mounted spare wheel. Forms part of the side spare wheel carrier, working with the anchor pl...

Heater Control Mounting Plate for left-hand drive applications. Fitted within the heater control assembly in the cab interior, this plate provides ...

Shim door GENUINE - door striker plate 1958 - 1984 - side hinged tailgate

Grille Spring Clip for securing the front grille panel on Series III models. Fitted at the grille mounting points, this spring clip retains the fro...

Heater Cable operates the tap-type heater control valve in the heating and ventilation system. It connects the dashboard heater control to the tap...

Seat Base Corner Capping in plastic. Fitted at the outer corners of the front seat base frame, this capping provides a neat finished edge and prote...

Rear Indicator Amber Lens

Fuel Filter Centre Bolt for the diesel fuel filter and sedimentor assembly. This through-bolt clamps the filter bowl and element onto the filter h...

Fuel Tank Mounting Washer is used at the fuel tank mounting points, spreading the clamping load of the fixing across the mounting bracket or strap....

Door Latch Shim - Rear - a packing shim for the rear door anti-burst latch, part of the door lock and handle assembly. Fitted behind the latch on ...

Harness Bracket Shim for the wiring harness mounting hardware. Fitted behind the harness support bracket at its mounting point, the shim sets the ...

Bump Stop for the suspension, mounted at the limit of axle travel. This rubber stop caps upward suspension movement at full compression, providing...

Screw - a threaded fastener used to join or secure components.

Engine & Gearbox Mount - Lower The lower (bottom) rubber mounting that isolates the engine and gearbox from the chassis, absorbing running vibr...

Fuel Filler Seal - sealing ring fitted at the fuel filler, part of the fuel tank filler assembly. Seals the joint at the filler neck to prevent fu...

Reverse Gate Bracket is the fixed section of the reverse-gate stop within the gear-lever mounting on the Series four-speed gearbox. It forms the g...

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Gearbox Top Cover Plate - the cover plate that closes the top aperture of the main gearbox casing. It seals the top of the gearbox over the select...

Choke Clip is the retaining clip that secures the choke cable at the Zenith carburettor. Part of the choke cable installation, it anchors the oute...

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Side Step Tread Rubber

Slip Ring for the horn contact in the steering column. This contact ring maintains the electrical connection to the horn as the steering wheel tur...

Gearbox Thrust Washer for the intermediate gear (laygear) in the main gearbox, used on 4-cylinder applications. It locates against the intermediat...

Mainshaft Nut - castellated nut that retains the assembled components on the rear of the gearbox mainshaft. The castellations accept a split pin to...