Products

Heater Tap Adaptor for the heater control circuit. This zinc-plated mild steel adaptor forms the threaded interface between the heater water valve ...

Fuel Filler Hose

Shackle Pin for the rear shackle of the front leaf spring. The pin pivots the spring shackle at the rear eye of the front road spring, locating th...

Thermostat - the coolant-flow control valve in the engine cooling system, with an 82°C opening temperature. Mounted in the thermostat housing at t...

Breather Hose - Oil Filler to Flame Trap for the engine crankcase ventilation system. This flexible hose connects the oil filler pipe outlet to th...

Blanking Plate for the inlet manifold of the 3.5L V8 twin-carburettor petrol engine. The plate closes off an unused port on the manifold to maintai...

Throttle Cable Bracket within the carburettor throttle control. Anchors the outer throttle cable, providing a fixed abutment so the inner cable ca...

Ball Joint

Side Lamp Lens in white glass for the Lucas military-pattern side lamp. The lens presses into the side lamp body to seal the bulb aperture and diff...

Red Glass Lens - a replacement lens for an exterior lamp unit. The lens seats over the lamp body to seal the bulb chamber and colour the emitted l...

Amber Military Glass Indicator Lens - Used

Carburettor Jet is a calibrated metering jet fitted within the carburettor fuel circuit. It controls the rate of fuel flow into the airstream, set...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Bolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...

Intake Elbow Seal for the 3.5L V8 twin-carburettor petrol engine. The seal sits between the air cleaner intake elbow and the carburettor intake to ...

Diesel Fuel Filter Plug Seal - a sealing ring for the drain plug on the diesel fuel filter and sedimentor. It seals the drain/bleed plug against t...

Carburettor Repair Kit for the six-cylinder petrol engine carburettor. It supplies the renewable service parts used to overhaul the carburettor and...

GENUINE LR camshaft sprocket for Rover V8 engines

Carburettor Gasket sealing the inlet manifold adaptor elbow to the carburettor on the Rover V8 twin-carburettor petrol engine. Fitted between the ...

Thermostat Housing Gasket seals the thermostat housing (water outlet elbow) to the intake manifold on the 3.5L carburettor V8 engine. It sits in t...

Bottle Cap for the coolant expansion bottle. Seals the coolant expansion reservoir and maintains system pressure within the cooling circuit.

Accelerator Cable connecting the accelerator pedal to the throttle linkage on the 3.5L V8 petrol engine. The cable transfers pedal travel to the c...

Radiator Hose - the top hose of the engine cooling circuit, connecting the cylinder head outlet to the top of the radiator. It carries heated cool...

Cup Washer is a dished washer used at the gearbox tie-rod (stabiliser rod) to chassis mounting on Series models. The cupped profile seats against ...

Set Screw retaining the top cover plate of the Series gearbox. A 4BA round-head fastener, sherardised finish, used to secure the cover plate on to...

Rivet is a permanent mechanical fastener used in the lower tailboard (drop-down tailgate) hinge assembly. Set through the hinge components, it for...

Screw for securing the window catch on Series hard top body variants. Used in the hard top glazing and catch assembly to retain the window catch m...

Nutsert - 5/16" UNF is a blind rivet nut (rivnut) with a 5/16" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal ...

Bush

Exhaust Valve Guide for the 2.6L six-cylinder petrol engine. The guide is pressed into the cylinder head and locates the exhaust valve stem, holdin...

Shakeproof Washer – a serrated, externally toothed lock washer used at the clutch hydraulic hose union. The teeth bite into both the mating surfac...

Bolt used in the LT95 gearbox and transfer assembly. It provides a torque-loaded, clamped fastening securing components within the LT95 transmissi...

Fuel Pump Gasket seals the external fuel pump to its mounting face in the fuel delivery system, preventing leakage at the joint. Used on petrol ap...

Pinion Oil Seal - seals the drive pinion shaft where it enters the Salisbury rear differential. Fitted at the nose of the differential housing, th...

Self-Tapping Screw for body and trim fixing applications. Used to secure window surrounds, bodyside trim, facia and switch panels. The self-tappin...

Headlamp Screw is a fastener used in the front headlamp assembly. It secures the headlamp unit and rim within their mounting, holding the lamp in ...

Screw – a black self-tapping screw with a pan head and Pozidriv drive recess, size No. 10 × 5/8 in, used to secure body, trim and panel fixings. B...