Products

Washer for the LT95 four-speed gearbox. It is an internal washer within the gearbox assembly.

Thrust Washer for the LT95 four-speed gearbox, 3.75mm thickness. This selective-thickness washer sets the end-float of the intermediate gear.

Transfer Box Inspection Cover - inspection plate for the transfer gearbox. Fitted over the inspection aperture in the transfer box casing, closing...

Differential Thrust Washer for the LT230 transfer box centre differential. It bears against the differential gears within the centre differential,...

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

Rear Fog Lamp Lens for use in the rear lighting unit assembly. This component forms the outer optical element of the fog lamp housing, positioned ...

bushes needed to machine the Series LT76 transfer case for the High Ratio Gear Set (HGRS.)

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Rear Door Seal for the rear door aperture on Series III and Defender 90 and 110. The rubber seal runs around the perimeter of the rear door apertu...

Door Hinge is the upper front door hinge for the right-hand side, part of the front door mounting assembly. It bolts to the body pillar and to the...

Wiring Harness Set is the main electrical loom that carries power and signal connections through the vehicle's electrical system, tying the chargin...

Door Check Strap Bracket – Rear – RH mounts the door check strap on the right-hand rear side door. The check strap limits how far the door swings ...

Bonnet Stop Buffer is a rubber buffer that cushions the bonnet where it rests against the body when closed. Mounted on the front bodywork, it supp...

Handbrake Gaiter for the handbrake lever assembly in Series II, IIA, and III Land Rovers. Fits 109-inch wheelbase V8-engined variants. The gaiter ...

Station Wagon Rear Side Window Glass - the small fixed glass pane for the rearmost side window aperture of the Station Wagon body. It glazes the r...

Tailgate Hinge Bolt secures the tailgate hinge to the rear body in the tailgate hinge assembly. Used on High Capacity Pick Up (HCPU) body configur...

Exterior Mirror with convex glass and a black finish, supplied as a complete door-mounted mirror assembly. The convex glass gives a wider rearward...

Glass

Door Lock - left-hand anti-burst latch assembly for the door closing and locking mechanism. The anti-burst design resists the latch springing open...

Rear Body Capping is the capping strip fitted along the top edge of the rear body side, covering and protecting the exposed panel edge and giving t...

Battery Cover Frame - Top is the upper frame section of the battery cover assembly. It forms the top of the battery enclosure, locating and retain...

Pipe seal

Handbrake Carrier Spacer for the handbrake assembly on Series II, IIA, III and Defender 90/110. This spacer fits within the handbrake carrier mech...

Main Wiring Loom for right-hand drive vehicles, forming the primary electrical harness that distributes power and signal throughout the vehicle. I...

Coolant Temperature Sensor - screws into the thermostat housing as part of the engine cooling system. It senses coolant temperature in the thermos...

Rear Fog Lamp forming part of the rear lighting assembly, providing a high-intensity red rear light for use in poor visibility. It operates on its...

Wheel Cap - LH for the Freelander 1 wheel arch assembly. This left-hand wheel capping is a trim component that covers and finishes the wheel arch ...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Conrod Bearing Set (big-end bearings) for the 2.6L 6-cylinder petrol engine. The shells sit between the connecting-rod big-ends and the crankshaft...

Lock Washer secures the retaining hardware on the layshaft (countershaft) within the manual gearbox. A tab on the washer is folded against the ret...

Brake Shoe Screw - a retaining screw within the drum brake assembly that secures the brake shoe in position. It holds the shoe located against the...

Oil Filter for the engine lubrication system, suited to the 2.0L and 2.6L IOE (inlet-over-exhaust) petrol engines. The filter traps metallic parti...

Oil Filter for the engine lubrication system of the 2.25L four-cylinder petrol and diesel engine. The filter traps combustion by-products, metal p...

Oil Seal for the swivel pin housing on the front axle, sealing against the polished surface of the swivel ball. The seal seats in the rear face of...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Voltage Regulator for the dynamo charging circuit – the Lucas RB340 control box. Wired between the C40 dynamo and the battery, the control box reg...

Piston ring set petrol 2,25 020 Mahle (per zuiger)

Rectifier Alt Acr

Piston Assembly for the 2.5L 4-cylinder turbo diesel engine, machined to +0.020" oversize for a rebored cylinder block. The piston transfers combu...

Lucar Connector - a fully insulated two-way in-line electrical connector for joining wiring within the loom. Of the Lucar (blade) terminal type, i...

Ignition Lead Set for the 3.5L Rover V8 petrol engine, carrying the high-tension spark from the distributor to the spark plugs. The set comprises ...