Products

Brake Vacuum Tank for the Land Rover Series III 2.25 Diesel. Fitted in the brake servo vacuum circuit, the tank stores a vacuum reserve to ensure c...

Timing Chain is part of the timing drive on the 3.6L V8 diesel (TDV8) engine. It transmits drive from the crankshaft to the camshafts, keeping val...

Timing Chain Guide for the TDV8 3.6 diesel engine, fitted within the timing chain assembly. The guide rails the timing chain as it runs between the...

Timing Chain Tensioner Arm is part of the timing drive on the 3.6L V8 diesel (TDV8) engine. The arm bears against the timing chain on its slack si...

Bolt - Special is an M22 metric timing gear bolt used in the engine timing gear assembly. This special bolt secures components within the timing g...

Cylinder Head Gasket (Right-Hand Bank) seals the joint between the right-hand cylinder head and the engine block on the 3.6L V8 32-valve diesel (Li...

Cylinder Head Gasket - LH seals the left-hand cylinder head to the engine block on the 3.6L V8 32-valve diesel (Lion TDV8) engine. It sits between...

Cylinder Head Gasket - LH seals the left-hand cylinder bank of the TDV8 3.6L V8 Turbo Diesel engine. This head gasket forms the combustion seal be...

Cylinder Head Gasket - LH - Grade 5 seals the left-hand cylinder head to the engine block on the 3.6L V8 32-valve diesel (Lion TDV8) engine. It si...

Cylinder Head Gasket - LH - Grade 5 seals the left-hand cylinder head to the engine block on the 3.6L V8 32-valve diesel (Lion TDV8) engine. It si...

Exhaust Manifold Gasket seals the joint between the exhaust manifold and the cylinder head on the TDV8 3.6L V8 Turbo Diesel engine. This gasket pr...

Instrument Voltage Stabiliser - a thermal bimetallic unit mounted on the back of the instrument cluster that regulates the supply voltage to the fu...

Body Sealing Plug, 25mm diameter, used to seal apertures in the body shell. This plug fits into holes in the floor, sill, or body panels - origina...

Wiper Motor Mounting Pad for the rear wiper motor, used on the Defender and Range Rover Classic. This rubber fixing pad sits between the wiper mot...

Banjo Adaptor is a hollow fitting used to connect a fuel line to a component port within the fuel system. This adaptor allows a hose or pipe to ex...

Braided Earth Strap with Battery Clamp - 300mm for the vehicle electrical grounding circuit. This braided copper earth strap is fitted with an int...

Battery Clamp - Negative is a single terminal clamp for the negative post of the battery. It secures the earth (negative) lead to the battery term...

Washer Fluid supplied in a 5-litre container. For use in the windscreen washer reservoir.

Mainshaft Bearing for the gearbox mainshaft - the centre bearing that supports the mainshaft within the gearbox casing. It locates and carries the...

Differential Breather Kit for venting pressure build-up from drivetrain assemblies, including differentials, the transmission, and the transfer cas...

Oil & Water Temperature Sensor threads into the engine and reports lubricant or coolant temperature to the engine management system and the ins...

Pump-Up Kit - US Standard fittings, High Temperature, Version 2. A portable tyre inflation accessory kit rated to 150 psi for use with ARB on-board...

Universal Joint - a cruciform-type drive joint used within a propshaft assembly to transmit torque between angled or misaligned shaft sections. In...

Alternator Bearing Kit - a service kit containing the bearing components required to recondition an alternator unit. Intended for use during alter...

Silencer - an exhaust silencer installed in the exhaust system to attenuate engine noise. Fits between the front pipe or intermediate section and ...

Lights and Heater Toggle Switch - a three-position Lucas-type toggle switch fitted to the dashboard switchgear. It acts as the master control for t...

Roof Tent Bracket - a mounting bracket for securing a roof tent to a vehicle's roof rack or load rails. Provides a fixed attachment point for roof...

Tow Ball & Pin is a towing coupling component that mounts to the tow bracket or drop plate. The ball provides the coupling point onto which a ...

Fuel Tank Filler Cap - Petrol/PHEV seals the fuel filler neck on petrol and plug-in hybrid (PHEV) fuel systems. It closes the filler neck to conta...

Fuel Tank Filler Cap Assembly for the fuel tank filler neck. It seals the filler neck to contain fuel vapour and maintain the sealed pressure of t...

Brake Front Disc Tr2-4a (Types A&b)

Brake Front Disc Tr3-6 (Type C)

Nut is a hexagonal nut cut with a 7/16" BSF (British Standard Fine) thread. It threads onto a matching 7/16" BSF bolt or stud to secure a bolted j...

Silencer Box for the Range Rover Classic V8 petrol exhaust system. This rear tailpipe and silencer assembly forms the final exhaust section on cat...

Glazing Rubber Strip - rubber glazing section supplied by the metre. It beds and seals a fixed glass panel into its body aperture, locating the gla...

Dowel A locating dowel for the engine cylinder block and cylinder head assembly. It seats in machined bores to align the cylinder head to the bloc...