Land Rover Discovery 2 Parts

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Rocker Arm - Steel - LH for the valve train of the Rover V8 engine, part of the Cylinder Head & Valve Train assembly. This steel rocker arm pi...

Fuel Connector Block Gasket for the Td5 2.5L five-cylinder diesel engine, sealing the fuel connector block to the engine within the fuel pressure r...

Centrifuge Oil Drain Pipe Gasket for the Td5 2.5L 5-cylinder turbo diesel engine. Seals the oil drain pipe at the engine's centrifugal oil cleaner...

Front Spring Spacers fit between the front axle and the base of the front coil spring to raise the spring mounting point. The spacers are 50mm (2 ...

Rear Crankshaft Oil Seal seated in the crankshaft rear oil seal housing at the back of the cylinder block, sealing the point where the crankshaft e...

Engine Coolant, pre-mixed for use in the engine cooling system. It circulates through the radiator, water pump and heater circuit to regulate opera...

Windscreen Finisher - the exterior trim moulding that finishes the upper edge of the front windscreen. Covers the top windscreen seal and the join...

ABS Sensor - Front for the wheel speed sensing circuit on the front axle. This is the short-type sensor, terminating directly in a connector. The ...

Circlip - Output Shaft Flange used within the transfer box output flange assembly to retain the output shaft bearing and associated components in p...

Drop Arm - Steering Box Output is installed on the steering box sector shaft within the power-assisted steering assembly. This component converts ...

Interior Trim Fixing Clip used within body and interior trim assemblies. This clip secures trim panels, insulation sections, ducting, and fascia c...

Bolt - a 3/8" UNC x 2-3/4" bolt securing the rocker shaft and its oil baffle plate to the cylinder head on the Rover V8 engine. It clamps the rock...

Fuel Tank Breather Hose for the fuel filler and tank ventilation circuit. Connects the fuel tank to the filler neck, venting the tank so that air ...

Flanged Screw - M6 × 12mm is a metric flanged-head fastener used in body, chassis, and electrical component assembly points on Land Rover vehicles....

Door Glass Channel for the side door glass assembly. The channel locates within the door frame and guides the window glass along its travel as it i...

Panhard Rod Bolt for securing the panhard rod to its axle bracket or chassis mount. This is a flanged hex bolt, M16 x 75mm. The integral flange di...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Extended Anti-Roll Bar Link for the left-hand side of the suspension, designed for use on vehicles with 2 to 3 inches of suspension lift. The stan...

Glow Plug

Body Rivet - a mechanical fastener used within the body and panel assembly to join thin sheet metal, trim and stowage fittings. Nominal size 3/16"...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Starter Motor for V8 petrol engines, operating within the engine electrical starting system. The solenoid-actuated pinion engages the flywheel rin...

ABS Modulator Switch Repair Kit serves the four-wheel anti-lock braking system, replacing the shuttle valve switch on the ABS modulator. The modul...

Flexible Brake Hose for the rear right-hand side, part of the hydraulic braking circuit. The hose forms the flexible link between the rigid brake ...

Flexible Brake Hose for the rear left-hand side, part of the hydraulic braking circuit. The hose forms the flexible link between the rigid brake p...

Ride Height Sensor - rear suspension height sensor for the self-levelling air suspension system. The sensor measures the position of the axle rela...

Suspension Bush - the outer pivot bush for the rear Watts linkage transverse link. The Watts linkage locates the rear axle laterally while permitt...

Radius Arm Bush for the front radius arm within the coil-sprung suspension assembly. The bush carries the radius arm at its chassis mounting. The ...

Coolant Hose connecting the radiator to the expansion tank. Part of the engine cooling circuit, this hose links the radiator to the coolant expans...

O-Ring for the fluid suction pipe of the ZF four-speed automatic transmission. Seals the joint at the suction (pick-up) pipe that draws automatic ...

Layshaft Bearing for the LT77 and R380 5-speed manual gearbox fitted to the Defender, Discovery 1, Discovery 2, and Range Rover P38. The layshaft ...

Bonnet Decal - Silver - self-adhesive exterior decal applied to the bonnet, finished in silver.

O-Ring for the fuel injector harness assembly on the Td5 2.5L 5-Cylinder Turbo Diesel engine. This O-ring provides a seal within the fuel injector...

Cylinder Head Dowel - Plastic is a locating pin fitted at the mating face between the cylinder block and cylinder head in the Td5 2.5L 5-cylinder t...

Layshaft Taper Roller Bearing supports the front of the layshaft in the manual gearbox. This is the grooved front bearing, sized 31.75 x 62.0 mm. ...

EGR Cooler Hose - Engine to Cooler is a coolant hose serving the exhaust gas recirculation (EGR) system. It carries engine coolant from the engine...

Propshaft Gaiter (Sliding Joint) is the flexible rubber boot that seals the sliding splined joint of the propshaft in the drivetrain. The sliding ...

Crankshaft Sensor Spacer for the Land Rover Td5 2.5-litre 5-cylinder turbo diesel engine in manual transmission applications. This spacer fits bet...

Gear Lever Spring for the manual gearbox gear change mechanism, providing the 1st/2nd selector bias. It works within the gear lever remote housing,...

O-Ring - Diff Lock - LT230 provides the hydraulic seal at the differential lock mechanism and front output shaft location within the LT230 transfer...

Gear Lever Spring for the manual gearbox gear change mechanism, providing the 5th gear selector bias. It works within the gear lever remote housing...

Mainshaft Bearing supports the mainshaft within the LT230 transfer box, carrying the shaft's rotational loads and keeping it running true as drive ...

Caged Captive Nut - an M8 nut held in a spring-steel cage that clips into a panel or bracket to provide a captive threaded fixing. It anchors the ...

Brake Union Washer is a sealing washer for hydraulic brake line connections. It seals the joint at a brake pipe or flexible hose union, fitting be...

Bonnet Release Cable for the Discovery 2 bonnet release system. This cable connects the interior bonnet release handle (located in the driver's fo...

Exhaust Manifold Bolt for the Rover V8 petrol engine, threaded 3/8" UNC and 1 1/8" long. The bolt secures the exhaust manifold to the cylinder hea...

O-Ring is a sealing ring used within the ZF 4-speed automatic gearbox and the LT230 transfer box. This O-ring seals fluid passages or housing inte...