Genuine Land Rover Parts

These locking wheel nuts are suitable for all alloy wheels that use original Land Rover alloy wheel nuts. Set of 5 locking wheel nuts and 1 key.

Core Plug - Cylinder Block Expansion Port is a pressed-steel sealing plug installed in the outer face of the cylinder block to close the casting ap...

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Single-Pole Bulb Holder fitted within the rear lamp assembly, providing the electrical interface and physical retention for the stop or tail lamp b...

Toebox Trim Fastener - the fixing that secures the footrest and toebox trim panel in the footwell. It retains the lower trim at the A-post and toe...

Torque Converter Housing Cover Gasket for the automatic transmission bell housing. It seals the lower access cover on the torque converter housing...

Rear Lamp Bulb Holder Double-pole bulb holder that seats in the rear lamp housing, retaining the bulb and carrying the electrical contacts between ...

Retaining Plate - gearchange grommet retaining plate for the transfer box. Secures the transfer box gearchange grommet where the gear lever passes...

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Washer - a general-purpose fixing washer used across multiple body, brake and chassis assemblies. It spreads the clamping load of a bolt or nut ov...

Exhaust Manifold Bolt for the Rover V8 petrol engine, threaded 3/8" UNC and 1 1/8" long. The bolt secures the exhaust manifold to the cylinder hea...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Set Screw - a fully threaded hexagonal-head setscrew with an M10 metric thread and a 20 mm length. A general-purpose fixing used at fastening point...

Interior Trim Fixing Clip used within body and interior trim assemblies. This clip secures trim panels, insulation sections, ducting, and fascia c...

Cable Tie for securing wiring looms and cables in Land Rover applications.

M6 Stud for the gearbox main casing. This threaded stud secures the speedometer drive housing to the transmission main casing, providing the fixin...

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Grommet - rubber sealing grommet, 3/4 inch overall diameter with 1/8 inch centre hole. Used to seal and protect wiring cables where they pass thro...

Clip - a retaining clip used to secure finisher mouldings and column shroud panels to their supporting structure. It locates and holds the mouldin...

Locking Wheel Nut for replacing one standard wheel nut per wheel as a theft deterrent. The locking wheel nut features a unique external drive prof...

Quarter Window Catch is the latching assembly for the side-opening rear quarter window, in the Lunar colour finish. Mounted to the hinged quarter ...

Fastener - black plastic drive-type (fir tree) push-in fastener used throughout the vehicle to secure body trim panels, interior linings, underbonn...

Early Seat Diaphragm Door Only - Discovery 1 4

Rear Side Door Channel is a glass run channel mounted within the rear side door, fitted to the right-hand (RH) side. The channel locates and guide...

Non-Return Valve for the V8 petrol engine, fitted to the inlet manifold vacuum take-off. The valve allows air to be drawn one way from the vacuum ...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Clevis pin

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

Land Rover Oval Name Badge - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground. Fitted to the front ...

Decal - ZF Automatic Gearbox is an adhesive identification label associated with the ZF automatic transmission, located in the centre console and c...

Heater Bypass Coolant Valve for V8 petrol applications. This vacuum-operated valve is installed in the HVAC coolant circuit and controls the flow ...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Brake pipe clip

Gearbox Filter Plug for the LT77 five-speed manual gearbox. The plug closes the bore in the extension case that gives access to the gearbox oil fil...

Swivel Pin Retaining Bolt A fixing bolt for the front axle swivel pin housing. It secures a swivel pin to the swivel pin housing, retaining the pi...

Sealing Washer is a copper joint washer used in multiple engine and ancillary applications across the Land Rover range, including as a sealing wash...

Hose Clip for securing flexible hoses to pipes and stubs throughout the Land Rover. Tightening the clip compresses the hose onto the stub to form a...

strip BTR919PUB

Tailgate Transfer Decal - "Discovery" Script - Mid Silver for the Discovery 1 body graphics assembly. This self-adhesive transfer decal carries th...

Door Hinge - Lower for the front door, mounted to the A-pillar to support and align the lower section of the door. Works in conjunction with the up...

Locking Wheel Nut Key - Code F for removing locking wheel nuts with the Code F drive profile, fitted to alloy wheels across the Defender, Discovery...

Remote Handset Case - replacement housing for the remote locking plip (key fob), supplied as the case only without the internal electronics. House...

Headlamp Bulb Cover for the front headlamp assembly. This rubber cover seals the bulb access aperture at the rear of the headlamp unit following b...

Bolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...

Differential Pinion Bearing Shim - 0.068 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Battery Fixing Stud - Long Straight is a long straight J-bolt used to secure the battery retaining clamp to the battery tray. The stud passes thro...

Roof Rack Side Rail Gasket for the front roof rack side rail mounting, left-hand upper position. This gasket seats between the front roof rack sid...

Roof Rack Side Rail Gasket for the front roof rack side rail mounting, right-hand upper position. This gasket seats between the front roof rack si...