Genuine Land Rover Parts

24v dsl long belt

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

"Land Rover" Rear Decal Badge A self-adhesive lettered name plate forming part of the exterior rear badging, applied to the rear bodywork. The let...

Fuel Tank Adaptor Ring secures the in-tank fuel pump and sender unit assembly into the aperture on the top of the fuel tank. The ring locks the pu...

Blanking Plug for closing an unused 13 mm (1/2") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

A-Pillar Trim Clip A retaining clip used in the interior A-pillar trim assembly. It secures the A-pillar trim panel to the body structure alongsid...

Land Rover Grille Name Plate - Black & Silver - front grille name plate carrying the Land Rover lettering, finished in black and silver. Mount...

Key Fob Cover Kit provides a replacement outer cover for the remote key fob, renewing a housing that has become worn, cracked or faded. It restore...

Air Suspension Reservoir for the Electronic Air Suspension (EAS) system. This pressure vessel (accumulator) stores a reserve of compressed air, en...

Air Cleaner Ring for the Range Rover L322 intake assembly. This sealing ring fits within the air cleaner housing on the BMW M62 B44 4.4-litre V8 p...

Torx Screw - 4.8 × 25mm for use in Land Rover body and trim assemblies. A metric Torx-head screw, 4.8mm diameter × 25mm length, for use where Torx...

Clip is a retaining clip in the front windscreen wiper linkage. It secures the wiper motor and linkage assembly, holding the linkage components to...

Land Rover Oval Name Badge - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground. Fitted to the front ...

Oval LAND ROVER Badge - gold lettering on a green background - for the tailgate. This is the classic oval "LAND ROVER" name badge fitted to the ex...

Hexagon Nut for use in electrical system assemblies.

Clip is a locking retaining clip in the front windscreen wiper linkage. It locks the wiper linkage connection, securing the motor and linkage asse...

Oil Cooler Gasket for the AJ-Series V8 petrol engine, sealing the oil cooler and filter housing to the cylinder block. This gasket forms the oil-t...

Coolant Hose forms part of the heater line within the engine cooling system, routing coolant between the engine and the heater matrix. Supplied co...

Water Outlet Connection (Upper) for the 4.4L DOHC V8 turbo-diesel (TDV8) engine. Part of the thermostat and coolant housing assembly, it carries co...

Timing Gear Bolt is the hex-head flanged bolt that retains the upper timing gear on the valve-timing drive. It secures the upper gear against the ...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Wheel Centre Cap for the road wheel, fitting into the centre bore of the rim to cover the hub. Finished in silver with a black logo. The cap conce...

Luggage Hook is a black loadspace hook mounted to the loadspace quarter trim. It provides an anchor point in the load area for securing luggage or...

Oil Seal for the rear differential, part of the rear axle final drive assembly. It seals the rotating shaft where it exits the differential housin...

Power Steering Hose Sealing Washer - seals the union between a power steering supply or return hose and its mating port in the steering hydraulic c...

Special Stud for the Range Rover L322 bonnet and tailgate area fixings. This stud is used in the bonnet assembly and luggage compartment door fixi...

EGR Thermostat Assembly that regulates coolant flow through the exhaust gas recirculation (EGR) cooler on the 2.7-litre V6 and 3.6-litre V8 diesel ...

Trim Clip is an interior trim fixing that retains the A-pillar trim panel against the body structure. Depending on application it also serves as t...

Hex Flange Nut - a flanged hexagonal nut used as a general threaded fastener across multiple vehicle assemblies. The integral flange spreads the c...

Clip retaining the top of the rear air spring within the rear spring and shock absorber assembly. The clip locates and secures the air spring at i...

Leak-Off Tube - Injection Pump

Brake Pad Set - Front - 18/19 Inch - friction pads for the front disc brake caliper assembly used with the larger front brake installation fitted b...

Exhaust Gas Temperature Sensor measures exhaust gas temperature at the front of the diesel particulate filter, in the upstream section of the after...

A-Pillar Finisher - the outer trim moulding for the left-hand A-pillar. It fits over the A-pillar between the windscreen and the front door apertu...

Cable Connector is a four-way electrical connector body used in the vehicle wiring harnesses. It joins a harness branch to its mating half, retain...

Brake Caliper - Rear - RH is the right-hand rear caliper of the disc brake assembly. Under hydraulic pressure from the rear brake circuit, it clam...

Rear Brake Caliper - Left-Hand is part of the rear braking assembly, mounting over the rear brake disc on the left-hand side of the vehicle. The c...

Number Plate Lamp Lens - clear lens for the rear licence plate lamp mounted in the luggage compartment door. The lens clips into the lamp housing ...

Asy Lamp

Exhaust Gasket sealing a flanged joint in the exhaust system on Land Rover and Range Rover models fitted with the 2.7L TDV6, 3.0D V6, 2.2D, and 4.4...

Worm Drive Hose Clamp used in the exhaust gas recirculation (EGR) circuit of the 3.0L M57 turbo diesel engine. The clamp secures a flexible hose o...

Washer - Sealing

Handbrake Shoe Set for the mechanical parking brake, which operates inside its own dedicated drum and is independent of the hydraulic service brake...

Plastic Rivet from the engine cooling assembly, used to retain the radiator and the coolant overflow container. The rivet is a push-fit fastener: ...

Brake Disc-Vented