Genuine Land Rover Parts

Wheel Centre Cap - a black alloy-wheel centre cap carrying the Land Rover oval in green and silver. It presses into the centre bore of an alloy wh...

Cable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

Grommet / Blanking Plug - Dash Bulkhead for Land Rover Defender. This rubber plug seals an unused aperture in the dash bulkhead (such as a heater ...

Oil Filter Gasket Kit for the engine oil filtration circuit of the 2.0L Ingenium (AJ200) engine, renewed with the oil filter element at each servic...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Bolt securing the fuel injector and high-pressure fuel pipe assembly on the engine fuel system. It clamps the injector and high-pressure pipe unio...

Cap - Filler

EGR Cooler Filter for the low-pressure exhaust gas recirculation circuit of the 2.0L I4 Ingenium diesel engine. The low-pressure EGR system draws ...

Oil Filter Element for the 3.0L AJ20 / AJ22 Ingenium six-cylinder engine, fitted in the engine lubrication circuit. The cartridge element seats in...

Blanking Plug - timing chain cover, supplied with its O-ring. Seals a machined service aperture in the timing chain cover of the Ingenium engine f...

Coolant Expansion Tank Cap - pressurised filler cap for the coolant expansion and overflow container in the engine cooling system. The cap sets th...

Wiper Blade for the rear window wiper assembly of the New Defender (L663). This blade uses the Aquablade design: washer fluid is channelled throug...

Wiper Blade for the front windscreen wiper assembly of the New Defender (L663, 2020 onwards). Fits the front wiper system on the Defender 90, Defe...

Magnetic Oil Drain Plug for the engine oil sump on the 2.0L Ingenium (AJ200/AJ20) four-cylinder petrol and diesel engines. The plug seals the drai...

Clip for exterior body trim and accessory fittings. The clip retains body mouldings, side steps, mudflaps and related exterior trim to the body, p...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Brake Disc Size Sv Frt 20/Rr 20 (From (VIN) S2000001)

Accessory Drive Belt for the 3.0L AJ20D6 Ingenium turbo diesel (High-output variant). This multi-ribbed serpentine belt sits in the accessory drive...

Clip retaining the top of the rear air spring within the rear spring and shock absorber assembly. The clip locates and secures the air spring at i...

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

Bonnet Latch for the bonnet (hood) closure mechanism. It engages the bonnet striker to hold the bonnet closed and releases it when operated, formin...

Washer - Sealing

Rear Brake Disc, 325 mm diameter, part of the rear service brake assembly. Supplied singly. The disc mounts to the rear wheel hub and provides the...

Outer body side finisher from the body side and front door aperture trim assembly, mounted externally along the body side where it meets the front ...

Rear brake disc, 365mm diameter, forming part of the rear brake disc and caliper assembly. The disc bolts to the rear hub flange and provides the ...

Front Brake Pad Kit - friction pad set for the front disc brake assembly, for the 380 mm front disc and size 20 caliper configuration. The pads lo...

Front Brake Caliper Attachment Kit - the caliper fitting hardware for the front disc brake assembly. The kit contains the brake pad clips and the ...

Bolt - hex-head bolt with washer, used in the splash and heat shield assembly. It secures the underbody splash shields and powertrain undertray pa...

Cable Connector - an electrical connector used in the vehicle wiring harness. The connector forms the termination between a harness cable and its ...

Intercooler (charge air cooler) for the turbocharger induction circuit, mounted at the front of the vehicle within the cooling pack airflow. Compr...

Exhaust Gas Pressure Sensor for the 2.0L AJ200D Ingenium four-cylinder diesel, working within the turbocharger and exhaust gas management circuit. ...

Injector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...

Head Gasket for the right-hand cylinder bank of the 5.0L V8 AJ133 petrol engine. It seals the cylinder head to the engine block, containing combust...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

Exhaust Pipe Gasket seals the front flanged joint of the exhaust system, maintaining a gas-tight connection and preventing exhaust leakage at the j...

O-Ring is a sealing ring used in the Exhaust Gas Recirculation (EGR) circuit of the 2.0L four-cylinder AJ200 diesel engine. It seals a joint in th...

Intercooler Pipe connecting the turbocharger outlet to the intercooler in the charge-air system of the 2.0L AJ200 (Ingenium) four-cylinder diesel e...

Climate Control Humidity Sensor, an input device for the automatic climate control system. Mounted at the base of the interior rear-view mirror, i...

O-Ring seal for the automatic transmission oil cooler circuit (ZF 8-speed, 8HP). The O-ring seals a connection in the transmission fluid cooling c...

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...

Drive Fastener - black plastic drive-in retaining clip used to secure body mouldings, trim panels and interior finishers to their mounting panels. ...

Front Strut Boot Kit renews the protective gaiter and mounting hardware for a front air suspension strut, part of the four-corner air suspension sy...