Genuine Land Rover Parts

Roof Rack Side Rail Gasket for the front roof rack side rail mounting, left-hand lower position. This gasket seats between the front roof rack sid...

Roof Rack Side Rail Gasket for the front roof rack side rail mounting, right-hand lower position. This gasket seats between the front roof rack si...

Roof Rack Side Rail Gasket - the rear sealing gasket for the roof rack side rail, part of the roof rack mounting assembly. It sits between the rea...

Roof Rack Side Rail Gasket for the rear roof rack side rail mounting, right-hand side. This gasket seats between the rear roof rack side rail and ...

Window Regulator for the front door, right-hand side, manual winder type (not electric). This is the mechanism that raises and lowers the front do...

Roof Gasket seals the joint between the roof panel and the body structure on the Discovery 1. The gasket runs around the roof panel perimeter, pre...

Differential Pinion Bearing Shim - 0.066 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Sunroof Handle Assembly operates the manually-operated glass sunroof, forming the interface between the occupant and the roof panel's opening mecha...

Spring Nut A clip-on spring-steel fastener, also known as a speed nut, used across body, grille and chassis fittings. It slides over a panel edge ...

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Panhard Rod Bush for the front suspension lateral location assembly. This rubber bush is pressed into the Panhard rod eye and provides the complia...

Spire Nut, a J-type sheet-metal spring nut (also known as a speed nut) used to secure trim, panels and fittings. The nut clips over a panel edge o...

Fixing Screw used in the flywheel, drive plate and clutch assembly. It is one of the threaded fasteners securing the flywheel or automatic drive p...

Camshaft Washer is a retaining washer used at the front of the camshaft within the timing drive of the 3.5L V8 petrol engine. It is fitted at the ...

Sealing Washer - a sealing washer used at cylinder head and thermostat housing joints within the cooling and lubrication circuit. Fitted beneath a...

Dowel used for the precise location and alignment of the front cover to the cylinder block on Rover V8 engines. These dowels ensure the front cove...

Locking Washer

Rocker Cover Screw for the Rover V8 petrol engine. This 1/4" UNC screw secures the valve (rocker) cover to the cylinder head. The rocker cover per...

Sealing Washer fitted at the engine front cover. Provides a leak-tight seal at a fastener or fitting on the front cover assembly.

Spring Clip - Steel for V8 EFI petrol engines, used in the throttle linkage and gear change mechanism. This steel spring clip provides positive re...

Camshaft Bolt for the Rover V8 engine, securing the camshaft sprocket to the front of the camshaft. This M12 x 30 mm bolt retains the camshaft dri...

Cap Reservoir Br.m.cylinder

Shakeproof Starlock Washer used within the clutch master cylinder and pipe assembly. The washer pushes onto a plain shaft or pin and grips it with...

Mainshaft for the R380 5-speed manual gearbox. The mainshaft is the central driven shaft within the R380 gearbox, carrying the output gear cluster...

Bolt, high tensile, M8 x 25mm. A metric hexagon head bolt for body, chassis, and structural fastening applications.

Tow Bar Kit - a bolt-on rear towing bracket assembly supplied with wired-in trailer electrics rather than a plug-in socket connection. It provides...

Spare Wheel Cover for Discovery 1 and Discovery 2, sized to fit a 255mm-wide tyre on a 16- or 18-inch wheel. The cover has a rigid backing panel a...

Camshaft Bearing Set for the Rover V8 petrol engine. This set provides the bearing surfaces on which the camshaft journals run within the cylinder...

Wastegate Control Hose for the 2.5L 200 TDi turbo diesel engine. This hose forms part of the turbocharger boost-control circuit. It routes the boo...

Sunroof Cable — drive cable for the sliding sunroof mechanism. The cable transmits drive from the sunroof operating mechanism to the panel, moving...

Bulb & Holder

Flywheel Bolt, 7/16" UNC x 1" hexagonal head, securing the flywheel to the rear crankshaft flange. Used on V8 petrol engines with manual transmiss...

Door Handle Assembly is the exterior handle for the left-hand front door, part of the front door locks and handles assembly. It mounts to the oute...

Bulb & Holder for the instrument panel warning lights. The assembly pairs an illumination bulb with its holder, which fits into the rear of the...

Steering Box Sector Shaft for the Adwest power-steering box. The sector shaft is the output shaft of the recirculating-ball steering box. The worm...

Pressure Seal

Speedometer Cable for the Discovery 1 instrument drive circuit. This mechanical drive cable connects the gearbox or transfer box output to the spe...

Rear Bumper Assembly for the Discovery 1. This is the complete rear bumper unit, fitted to Discovery 1 vehicles built up to (V)LA series. It mount...

Accelerator Cable for the Discovery 1 200TDi fuel injection system. This cable connects the accelerator pedal to the injection pump, transmitting ...