Land Rover Defender Parts

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Timing Chain Kit for the Ingenium 2.0L 4-cylinder engine, covering the complete timing chain system. The Ingenium AJ200 engine uses a dual-chain a...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Knock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...

Oil Cooler Gasket seals the oil cooler within the oil cooler and filter housing assembly. It maintains the oil-tight joint between the cooler and ...

Injector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Timing Chain Tensioner Arm bears against the timing chain within the timing drive assembly, providing the face through which the tensioner applies ...

O-Ring sealing the variable valve timing (VVT) solenoid cover. Seals the VVT solenoid cover within the engine timing gear, preventing oil leakage ...

Guide - Timing Chain

Brake Light Switch

Nut and Washer Assembly is an M6 hexagonal nut supplied together with its washer as a single assembly. The washer spreads the clamping load across...

Wheel Bearing Circlip - 51 mm retaining ring for the wheel hub bearing. Seats in the groove of the knuckle bore and locates the hub bearing axiall...

Timing Chain Guide - LH Primary - a fixed guide in the timing drive assembly of the 2.0L four-cylinder Ingenium petrol engine (AJ200 / AJ20P4), inc...

Timing Chain Guide - LH Primary - a fixed guide in the timing drive assembly of the 2.0L four-cylinder Ingenium petrol engine (AJ200 / AJ20P4), inc...

Drive Chain Idler - timing gear idler sprocket for the 2.0L four-cylinder Ingenium engine family (AJ200 / AJ20 series, petrol and diesel). The idl...

Arm - Timing Chain Tensioner

O-Ring for the high-pressure diesel fuel injection pump. The ring seals the joint between the pump body and its mounting face on the engine, preve...

Coolant Temperature Sensor mounted in the cylinder head coolant gallery, part of the engine cooling and engine management system. The sensor is a ...

Valve stem seal for the cylinder head valve train. The seal locates on the valve guide and wipes the valve stem as it reciprocates, metering the s...

Timing Chain Guide, Lower Primary from the front timing gear assembly. It bears against the primary drive chain on the run between the crankshaft ...

Exhaust Clamp for the 2.0L Ingenium diesel exhaust system (AJ200D / AJ20D4). The clamp secures the front section joint of the exhaust, holding the...

Timing Gear Bolt - special-form fastener used in the timing drive assembly at the front of the Ingenium petrol engine. It is one of the fixings th...

Timing Chain Tensioner Arm is the pivoting guide arm in the timing drive of the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4 / AJ200P ...

EGR Inlet Gasket for the 2.0L AJ200 Ingenium diesel Exhaust Gas Recirculation system. Seals the inlet joint of the EGR assembly to maintain a gas-...

Front Crankshaft Oil Seal for the AJ200 2.0L four-cylinder petrol and diesel engine. It seals the front of the crankshaft where it passes through t...

Cylinder Head Gasket for the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4). The gasket seals the joint between the cylinder head and ...

Knock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Guide - Timing Chain

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

O-Ring is a 60mm sealing ring used in the Exhaust Gas Recirculation (EGR) circuit of the 2.0L four-cylinder diesel engine (AJ200 / AJ20D4 family). ...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit. This seal maintains a gas-tight joint within the EGR section, sealing the connection betwe...

Front Crankshaft Oil Seal for the AJ200 2.0L four-cylinder petrol and diesel engine. It seals the front of the crankshaft where it passes through t...

Front Crankshaft Oil Seal located at the front of the cylinder block, on the crankshaft. Seals the crankshaft where it exits the front of the engi...

TMAP Sensor is the combined intake air temperature and manifold absolute pressure sensor, fitted to the inlet manifold and intercooler ducting. It...

MAP Sensor is the manifold absolute pressure and charge-air temperature sensor mounted in the inlet manifold. It reports intake manifold pressure ...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit. This seal maintains a gas-tight joint within the EGR section, sealing the connection betwe...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit, 60mm. This seal maintains a gas-tight joint within the EGR section, sealing the connection...

Exhaust Gas Recirculation Gasket seals the exhaust gas recirculation (EGR) connection on the left-hand side, maintaining a gas-tight joint within t...