Land Rover Freelander Parts

Washer Jet Tube Tee Piece - a T-shaped connector in the windscreen washer system. The tee piece connects into the small-bore washer tubing, joinin...

Tailgate Handle is the exterior handle assembly for the rear tailgate, operating the tailgate latch release. The assembly incorporates the rear nu...

O-Ring seals the thermostat housing on the K Series 1.8 and KV6 2.5 engines. It sits at the joint between the thermostat housing and outlet elbow ...

Gear Lever Gaiter for the manual gearshift, fitted around the base of the gear lever where it passes through the centre console. The gaiter seals ...

Sunroof Drive Cable for the sliding sunroof mechanism. Transmits drive from the sunroof motor to the panel carriage, moving the sunroof glass alon...

Rear Door Latch Assembly - the latching and locking mechanism for the rear door. It engages the striker on the body aperture to hold the rear door...

Fuel Tank Inspection Plate Seal is a rubber sealing gasket for the fuel tank inspection plate in the fuel tank assembly. The inspection plate prov...

Injector Sealing Washer seals each fuel injector into the cylinder head within the diesel fuel injection system, for 200 TDi and 300 TDi turbo-dies...

Exhaust Mounting - Rubber is a rubber isolator in the exhaust suspension system, fitted between the exhaust assembly and the vehicle underbody. Th...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Engine Tie Rod - lower torque rod within the engine mounting system. It ties the powertrain to the subframe and resists the fore-and-aft rocking (t...

Rear Bumper Lamp, Right-Hand Side. Lamp unit installed in the right-hand side of the rear bumper, forming part of the rear exterior lighting assemb...

Land Rover Oval Name Badge - Plastic - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground, moulded in ...

Fuel Tank Locking Ring for the fuel pump and sender unit assembly. This ring secures the fuel pump and sender unit in the top of the fuel tank, pr...

Snap Sac Clip - a push-fit fastener that retains the interior door trim panel (door casing) to the door. The clip locates in the door frame and gr...

Headlamp

Wheel Cap - LH for the Freelander 1 wheel arch assembly. This left-hand wheel capping is a trim component that covers and finishes the wheel arch ...

Rear Wiper Arm is the wiper arm assembly for the rear screen. It carries the rear wiper blade across the tailgate glass and includes the integral ...

O-Ring - Fuel Injector - Diesel - sealing ring in the fuel injector and pipe assembly on diesel engines. The ring seals the injector joint against...

Anti Roll Bar Bush locates the anti-roll bar in its chassis mounting bracket, providing a resilient rubber interface between the bar and the subfra...

Rear Stop and Flasher Lamp for installation in the left-hand position of the rear bumper. This unit provides the stop lamp and direction indicator...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Hex Nut, M24 x 1.5mm securing the constant-velocity (CV) joint stub shaft to the wheel hub within the driveline. The nut retains the CV joint and ...

Brake Light Switch for the braking and signalling circuit. Mounted at the brake pedal assembly, this switch closes when the pedal is depressed, co...

Cap - Overflow Container

Snap-sac trim clip - the push-in plastic fastener that secures interior trim panels to their supporting structure. The clip passes through a hole ...

Headlamp Assembly - left-hand unit for left-hand-drive vehicles. Supplied as a complete headlamp and flasher unit comprising the housing, reflecto...

Finisher Clip - a retaining clip for exterior body finishers and mouldings. The clip secures a trim finisher or moulding to the body panel, engagi...

Rod tie assy lower Engine Mounting: - 1.8 K16 Petrol upto (VIN) YA999999 - Tcie L Series Diesel upto (VIN) YA999999

Rear Quarterlight Catch Assembly latches the opening rear quarterlight (sixthlight) glass. This right-hand assembly secures the hinged rear side g...

Crankshaft Pulley - timing drive pulley for the 1.8L K-Series 16-valve petrol engine. Fits to the nose of the crankshaft and carries the toothed t...

EGR Valve for the exhaust gas recirculation circuit on Td5 2.5L 5-cylinder turbo diesel and 2.0L L-Series diesel engines. The valve meters a contr...

Anti-Roll Bar Bracket secures the front anti-roll bar to the vehicle structure. The bracket clamps over the anti-roll bar mounting bush and bolts ...

Sunroof Pivot Block for the sliding sunroof mechanism. Right-hand pivot block that guides and supports the sunroof panel within its cassette on th...