for Discounts / VAT
for Discounts & Correct VAT
Parts for the full Land Rover Series family, produced from 1948 to 1985. This collection covers Series I, Series II, Series IIA, and Series III in both short wheelbase and long wheelbase configurations. Select your generation below to find correctly fitted components for your vehicle.
Fuel Lift Pump for the 2.25-litre four-cylinder petrol engine, mounted on the side of the cylinder block and sitting in the fuel supply circuit bet...
View full detailsTrack Rod End ball joint for the front steering linkage, used at the drag link position where the linkage connects to the steering relay or steerin...
View full detailsTrack Rod End ball joint for the front steering linkage, forming the articulating connection between the steering rod and the steering arm on the s...
View full detailsShock Absorber for the rear suspension, heavy-duty specification. The damper is mounted between the rear axle and its chassis bracket and controls...
View full detailsEngine Gasket Set - V8
Gearbox 1st Speed Gear for the LT76 four-speed manual gearbox. This gear provides the first (lowest) forward ratio within the gearbox main gear tr...
View full detailsFlywheel for the 2.25L petrol engine in its 3-main-bearing configuration. Bolted to the rear flange of the crankshaft, the flywheel stores rotatio...
View full detailsStud
Low Fuel Monitor Unit for 24V electrical systems, operating in the fuel level indication circuit. The unit processes the signal from the fuel tank...
View full detailsBulkhead Mudshield, left-hand - inner wing to bulkhead splash plate, right-hand drive applications. The mudshield closes the gap between the inner...
View full detailsBulkhead Mudshield, right-hand - inner wing to bulkhead splash plate, right-hand drive applications. The mudshield closes the gap between the inne...
View full detailsElectronic Ignition Kit for the Rover V8 petrol engine with a points-type distributor. The kit replaces the mechanical contact points and condenser...
View full detailsSteering Damper mounts across the steering linkage to absorb shocks and damp oscillation (bump steer and wheel shimmy) fed back through the track r...
View full detailsSteering Damper mounts across the steering linkage to absorb shocks and damp oscillation (bump steer and wheel shimmy) fed back through the track r...
View full detailsBrake Pipe Set - a complete set of pre-formed steel brake pipes for a single-line hydraulic braking circuit in left-hand-drive configuration. The p...
View full detailsBrake Pipe Set - a complete set of pre-formed steel brake pipes for the vehicle's hydraulic braking circuit, matched to the Suffix G production spe...
View full detailsPropshaft UJ Silicone Sleeve fits over the rear propshaft universal joint on 63 mm diameter propshafts. It shields the joint from road dirt, grit a...
View full detailsB-Post - long-wheelbase Station Wagon with second-row doors. The B-post is the vertical body pillar between the front and second-row door apertures...
View full detailsSliding Window Seal - the replacement rubber sealing strip for the standard rear sliding window kit fitted to hard-top bodies. The seal beds the s...
View full detailsSwivel Housing Gaiter Kit - Series - Ltwt
Clutch Kit for the 9.5 inch single dry-plate clutch assembly, which sits between the flywheel and the gearbox input shaft and transmits engine driv...
View full detailsCentre Cubby Box - Techno finish. A console box that mounts on the transmission tunnel between the front seats, providing enclosed central storage ...
View full detailsHigh-Top Centre Cubby Box in grey. A Defender-style console box that mounts on the transmission tunnel between the front seats, providing enclosed ...
View full detailsWheel Cover 205 x 16
Piston for the 3.5L V8 petrol engine, standard (nominal) bore size. It reciprocates within the cylinder bore, transmitting combustion pressure thr...
View full detailsHeadlamp Guard in moulded plastic. A protective guard fitted over the headlamp lens to shield it from stone chips, debris and impact damage. Suppl...
View full detailsWindscreen Glass - replacement glass panel for the windscreen frame. Fits the windscreen aperture as a direct replacement for cracked or damaged g...
View full detailsDoor Trim Retainer - upper horizontal retainer for the rear end door window. This retainer secures the upper edge of the glass within the rear end...
View full detailsTie Tube - a side brace for the full-length soft-top hood frame assembly on long-wheelbase Land Rover vehicles. This tube provides lateral structu...
View full detailsHoodstick - the rearmost bow of the soft-top canvas roof framework on Land Rover Series and Defender vehicles. This hoodstick forms the rear struc...
View full detailsHoodstick - front bow of the soft-top hood frame. This steel bow forms the front arch of the soft-top hood frame, providing structural support at ...
View full detailsWing Stay for the rear body structure of the Series Land Rover. This right-hand steel bracket braces the rear wing to the body sill, providing str...
View full detailsDoor Cap (Galvanised, Right-Hand) is the capping rail that forms the top edge of the right-hand front door frame around the window aperture. The g...
View full detailsBench Seat Backrest in techno fabric, forming the upright back section of the folding rear load area bench seat. This 810mm wide backrest mounts t...
View full detailsBench Seat Backrest in black vinyl, forming the upright back section of the folding rear load area bench seat. This 810mm wide backrest mounts to ...
View full detailsValve Rocker for the Land Rover 2.25L four-cylinder diesel engine - right-hand exhaust rocker arm. Pivots on the rocker shaft in the cylinder head ...
View full detailsSmall Gasket for 269974
Outer Wing is the left-hand front wing outer skin panel, moulded in ABS plastic. It forms the visible outer surface of the front wing, covering th...
View full detailsOil Filter Adaptor for the engine lubrication circuit, mounting the oil filter to the cylinder block. The adaptor forms the interface between the ...
View full detailsCV Boot Kit
Rear Window Glass for the rear door, part of the rear door glazing. Heated glass with an integral electric demist element and a Sundym solar tint, ...
View full detailsStop/Tail Lamp Assembly for the rear lighting circuit, combining the tail (running) light and stop (brake) light in a single LED unit. The assembl...
View full detailsPiston ring set for the 3.5L Rover V8 petrol engine, supplied per piston. The rings seal the combustion chamber against the cylinder bore, transfe...
View full detailsConnecting rod bearing set - the big-end shells of the 2.25L four-cylinder engine, running between the connecting rod big-end eyes and the cranksha...
View full detailsMain bearing set for the three-bearing 2.25L four-cylinder engine, forming the crankshaft support in the cylinder block bottom end. The shells loc...
View full detailsMain Bearing Set - 0.020in Undersize - crankshaft main bearing shells for the 3.5 and 3.9 litre V8 petrol engine, sized for a crankshaft that has b...
View full detailsSteering Box for manual, non-power-assisted steering. The steering box converts rotation of the steering wheel and column into angular movement of...
View full detailsBrake Pipe forming the short rigid link between the front flexible hose bracket and the top wheel cylinder in the front drum brake hydraulic circui...
View full detailsParts for the full Land Rover Series family, produced from 1948 to 1985. This collection covers Series I, Series II, Series IIA, and Series III in both short wheelbase and long wheelbase configurations. Select your generation below to find correctly fitted components for your vehicle.
80, 86, 88 and 107-inch wheelbase variants. 1.6-litre and 2.0-litre petrol, 2.0-litre diesel from 1957.
Land Rover Series I parts (1948 to 1958) →88-inch SWB and 109-inch LWB. 2.25-litre petrol and diesel, 2.6-litre straight-six and 3.5-litre V8 in select variants.
Land Rover Series II, IIA and III parts (1958 to 1985) →The Land Rover Series family spans four distinct generations produced across 37 years. Series I ran from 1948 to 1958, Series II from 1958 to 1961, Series IIA from 1961 to 1971, and Series III from 1971 to 1985. Each generation used a body-on-frame ladder chassis with selectable four-wheel drive, a two-speed transfer gearbox, and a four-speed manual main gearbox. Wheelbase options were 88 inches (short wheelbase) and 109 inches (long wheelbase) from Series II onward. Series I used wheelbase options of 80, 86, 88, and 107 inches across its production run.
Parts compatibility is not uniform across the family. Some components, particularly engine internals for the 2.25-litre petrol and diesel units, carry across from Series IIA through Series III. Others, including body panels, wiring looms, and axle components, are generation or wheelbase specific. Selecting the correct child collection for your vehicle is the most reliable way to find the right parts.
Browse by generation:
If you are unsure which generation you have, use the vehicle commission number to identify your build date and sub-series before selecting parts.
The Land Rover Heritage Trust holds production records and commission number data for the Series family and is a reliable resource for vehicle identification.
This collection covers components across all major categories for the Series family. The heaviest demand comes from engine and gasket components, suspension and steering parts, body and chassis hardware, electrical and wiring items, and service and maintenance consumables.
Common restoration categories include engine rebuild components (gaskets, seals, bearings, timing parts), swivel housing and axle parts, wiring looms and electrical connectors, body panels and bulkhead sections, brake system components, and clutch and drivetrain parts.
For cross-category browsing by component type, the following category collections carry Series-compatible stock alongside parts for other Land Rover models:
Use the Model filter available on category collection pages to narrow results to Series I or Series 2 and 3 fitment where supported.
Buying GuideThe product grid offers three quality tiers: Genuine, OEM, and Aftermarket.
Genuine parts carry the original Land Rover part number and were manufactured by or for Land Rover. For Series vehicles, genuine Land Rover stock is limited for many components due to the age of the range. Where genuine parts are available, they are listed as Genuine.
OEM parts are manufactured to the same specification as the original part, often by the same supplier that produced the original component, but are sold outside the main brand distribution channel. For Series vehicles, OEM-specification parts are a reliable and widely used choice for mechanical rebuilds.
Aftermarket parts are independently manufactured to a compatible specification. Quality varies by product, and each listing on this site identifies the quality tier clearly. For consumable and body hardware categories on Series vehicles, quality aftermarket parts are the standard choice used by workshops across Europe.
Trade BuyersTrade customers running a workshop or managing multiple Series vehicles can access volume pricing through a Budget Parts trade account. Trade accounts include correct EU VAT invoicing, consolidated order options, and direct contact with the sourcing team for unlisted parts.
If a component is not currently visible in the catalogue, the sourcing team works directly with UK and EU suppliers to locate it. Contact the team with your commission number and part requirement.
Vehicle IdentificationSeries Land Rovers do not carry a modern 17-digit VIN. Each vehicle has a Commission Number on a bulkhead plate that encodes the generation, engine type, wheelbase and build date. Since the identification process and the records you cross-reference against differ between the four generations, the detailed Commission Number guidance lives on the two child collections, scoped to the vehicles each one covers.
For Series I (1948 to 1958), see the Series 1 collection. For Series II, IIA and III (1958 to 1985), see the Series 2 and 3 collection. Both pages cover where the plate sits on each generation, what the encoding tells you, and what to do if the plate is missing. If you have your Commission Number to hand and want fitment confirmed before ordering, contact Budget Parts directly.
Background ReadingFor deeper engineering and restoration context beyond the scope of this hub page, the following long-form guides cover each generation in detail. They are reference reading rather than navigation; the two child collections above are the route to parts.
A detailed reference covering Series I engine variants (1.6-litre and 2.0-litre petrol, 2.0-litre diesel), chassis design, wheelbase evolution, and the critical parts considerations for accurate restoration. Relevant for anyone sourcing components for a Series I vehicle or confirming specifications before ordering.
Series I engine and restoration guide →Covers the engineering and production history of Series II, IIA, and III models, including key differences between generations, engine fitment across sub-variants, and why certain parts are interchangeable while others are not. Useful background before selecting parts from the Series 2 and 3 collection.
Series II, IIA and III restoration guide →These are four successive generations of the same utility vehicle family, each sharing the core body-on-frame architecture but differing in engine, bodywork, and specification. Series I ran from 1948 to 1958 and used a 1.6-litre then 2.0-litre petrol engine, with a diesel option from 1957. Series II ran from 1958 to 1961 and introduced a revised body style. Series IIA ran from 1961 to 1971 and is the highest-volume production variant, available with 2.25-litre petrol and diesel engines and, in certain long wheelbase models, a 2.6-litre straight-six. Series III ran from 1971 to 1985 and brought minor updates including a revised instrument panel and an optional 3.5-litre V8 in select variants. Understanding which generation you have is the essential first step in selecting the correct parts.
Some parts are shared across Series IIA and Series III, particularly engine internals for the 2.25-litre petrol and diesel units, and certain axle and drivetrain components. However, body panels, wiring configurations, and some suspension components differ between generations. Parts shared across Series II and Series IIA are sometimes also different from early and late Series III specifications. The safest approach is to confirm fitment by generation and wheelbase before ordering, and to use the Series 2 and 3 parts collection for those specific generations.
Yes, significantly. Series I vehicles used different wheelbase dimensions (80, 86, 88, and 107 inches depending on year), different body construction details, and earlier engine specifications including the 1.6-litre petrol and the pre-2.25-litre 2.0-litre units. Many body, chassis, and mechanical components are unique to the Series I and do not carry across to Series II or later. The Series 1 parts collection is dedicated to this generation.
Start by identifying which generation your vehicle is. Series I (1948 to 1958) parts are unique to that generation in body, chassis and engine, and live in the Series 1 collection. Series II (1958 to 1961), Series IIA (1961 to 1971) and Series III (1971 to 1985) share considerable parts overlap and are grouped together in the Series 2 and 3 collection. If you are not sure which generation you have, the Commission Number on the bulkhead plate will tell you, and the child collections cover identification in more detail. Use the generation grid above to navigate to the correct collection for your vehicle.
Yes. The Series Land Rover aftermarket is one of the most active classic vehicle parts ecosystems in Europe. New replacement parts are produced for all four generations across the major categories: engine internals for the 2.25-litre petrol and diesel and the 2.0-litre Series I engines, body panels and chassis sections, electrical and wiring components, brake and suspension parts, and full restoration hardware. Genuine Land Rover stock is limited for parts of this age, but OEM-specification parts and quality aftermarket equivalents cover the majority of components in active demand. Specialist UK and EU manufacturers continue to remanufacture Series-specific items, and Budget Parts sources from this network for items not held in catalogue stock.
Start with three steps. First, identify your generation precisely (Series I, II, IIA or III) and your wheelbase, because every parts decision flows from those two facts. Second, work through a baseline service of consumables and wear items: brakes, fluids, filters, ignition components on petrol engines, glow plugs and fuel filters on diesels. Third, plan ahead for the higher-cost restoration items that often surface on Series vehicles after a few months of use, such as bulkhead repair sections, chassis outriggers, swivel housings and gearbox components. The two child collections (Series 1, and Series 2 and 3) hold the parts. The Series I and Series II/IIA/III restoration guides linked below cover the engineering background, common faults and parts priorities for each generation in more depth.