Land Rover Defender New Parts

Exhaust Clamp for the 2.0L Ingenium diesel exhaust system (AJ200D / AJ20D4). The clamp secures the front section joint of the exhaust, holding the...

Oil Filter Element for the 3.0L AJ20 / AJ22 Ingenium six-cylinder engine, fitted in the engine lubrication circuit. The cartridge element seats in...

Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...

Bolt - interior trim fixing bolt from the instrument panel and floor console fastener group. It secures instrument panel mountings, the floor cons...

EGR Inlet Gasket for the exhaust gas recirculation circuit of the 2.0L I4 AJ200 Ingenium diesel engine. The gasket seals the EGR inlet joint on th...

Wheel Centre Cap - hub cover for modular steel road wheels. It press-fits into the centre bore of the wheel, covering the hub flange and keeping d...

Timing Cover Blanking Plug - threaded plug that closes an aperture in the front timing cover of the 2.0L Ingenium petrol engine (AJ200 / AJ20P4, al...

Transfer Case Fluid - the synthetic lubricant specified for the electronically controlled transfer case in the four-wheel-drive driveline. The flu...

Seal - Oil

Roof Rack Sliding Nut Plate - 8 mm T-slot nut plate for aluminium expedition roof rack platforms, supplied in packs of ten. The plate slides into ...

Timing Gear Bolt - special-form fastener used in the timing drive assembly at the front of the Ingenium petrol engine. It is one of the fixings th...

Air Filter from the engine air intake system, seated in the airbox between the intake duct and the induction tract. Traps airborne dust and debris...

PCV Valve Service Kit

PCV Valve Service Kit - service parts for the positive crankcase ventilation valve, which sits in the crankcase emission control system on the cyli...

PCV Valve Service Kit

Air Filter Element from the engine air intake system, seated in the airbox between the intake duct and the induction tract. Traps airborne dust an...

Turbocharger Coolant Hose from the engine cooling circuit, serving the turbocharger on the 3.0L AJ20P6 petrol engine. The hose carries engine cool...

Front Wiper Blade - windscreen wiper blade for the front wiper arm and linkage assembly. It clips to the wiper arm and carries the rubber wiping e...

Timing Chain Tensioner Arm is the pivoting guide arm in the timing drive of the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4 / AJ200P ...

O-Ring - seals a joint in the thermostat housing and EGR cooling circuit. Fitted to the 2.0L four-cylinder AJ200 diesel engine, it maintains a lea...

Cylinder Head Bolt for Ingenium petrol engines (1.5L AJ20P3, 2.0L AJ200 / AJ20P4, 3.0L AJ20P6 / AJ22P6). The bolt clamps the cylinder head to the ...

Brake Pad Wear Wire - front brake pad wear warning wire within the braking system. Routed to the front brake pad, the wire completes a circuit tha...

EGR Inlet Gasket for the 2.0L AJ200 Ingenium diesel Exhaust Gas Recirculation system. Seals the inlet joint of the EGR assembly to maintain a gas-...

Coolant Tube forming the primary coolant path between the cylinder block and the water outlet. This aluminium tube carries coolant from the engine...

MAP Sensor - the manifold absolute pressure sensor in the engine management system, mounted on the inlet manifold. It measures the pressure of the...

Front Crankshaft Oil Seal for the AJ200 2.0L four-cylinder petrol and diesel engine. It seals the front of the crankshaft where it passes through t...

Cylinder Head Gasket for the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4). The gasket seals the joint between the cylinder head and ...

Knock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...

Exhaust Pipe Gasket seals the front flanged joint of the exhaust system, maintaining a gas-tight connection and preventing exhaust leakage at the j...

Timing Gear Bolt - a fixing bolt in the engine timing drive, retaining a timing gear. It secures the timing gear on the 2.0L four-cylinder AJ200 p...

Washer Reservoir Cap for the windscreen washer fluid reservoir. Seals the filler neck of the washer bottle in the wash/wipe system, retaining wash...

Output Shaft Seal for the transfer box. It seals around the transfer case output shaft, retaining lubricant inside the transfer box and preventing ...

Cylinder Head Gasket for the 5.0L V8 AJ133 petrol engine. The gasket seals the joint between a cylinder head and the engine block, containing comb...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Brake Pad Wear Wire - front brake pad wear warning wire within the braking system. Routed to the front brake pad, the wire completes a circuit tha...

Connector - Valve Block to Pipe for the air suspension system. This fitting joins the air suspension valve block to the air line, forming the seal...

O-Ring is a sealing ring used in the Exhaust Gas Recirculation (EGR) circuit of the 2.0L four-cylinder AJ200 diesel engine. It seals a joint in th...

Guide - Timing Chain

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Cup Holder - an interior trim component fitted to the floor (centre) console. It provides a moulded holder to retain cups or containers within the...

Output Shaft Seal for the transfer box. It seals around the transfer case output shaft, retaining lubricant inside the transfer box and preventing ...

O-Ring is a 60mm sealing ring used in the Exhaust Gas Recirculation (EGR) circuit of the 2.0L four-cylinder diesel engine (AJ200 / AJ20D4 family). ...