Price <10

Sealing Washer for diesel fuel injectors, positioned at the injector nozzle seat in the cylinder head to seal against combustion gases around the i...

Brake Pad Fitting Kit for front brake assemblies running vented discs. The kit supplies the retaining hardware that secures and correctly positions...

Joint Washer - front timing cover gasket for Land Rover 4-cylinder petrol and diesel engines. This gasket seals the mating face between the front ...

Drive Flange Gasket

Spring Washer fitted under a nut or bolt head to resist loosening from vibration. An M8 split-ring (single-coil) spring washer. The sprung opening...

Gearbox Front Cover Oil Seal for the manual gearbox front cover, sealing around the primary (input) shaft. Retains gearbox oil and excludes dirt a...

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

Oil Seal - a radial oil seal fitted between the wheel hub and stub axle within the wheel hub and drive shaft assembly. The seal retains lubricant ...

Fuel Connector Block Strainer O-Ring for the Td5 2.5L 5-Cylinder diesel engine. This O-ring seals the strainer within the fuel connector block, pr...

Reverse Lamp Bulb - a 21W 12V single-filament incandescent bulb (type P21W) with a BA15s single-contact bayonet cap, fitted to the rear lamp assemb...

Fir Tree Fastener in light grey, for the roof trim and headlining assembly. Push-fit fastener that secures roof trim panels and headlining ancilla...

Water Pump Housing Gasket for the 300 TDi cooling circuit, sealing the coolant pump distance piece to the cylinder block. The gasket forms the coo...

Spire Clip used to retain front wing panels and heater assembly components. This spring-steel clip slides over a screw or stud thread and grips se...

Carburettor Manifold Gasket for the 2.25L petrol and carburettor-equipped Defender engines. This gasket seals at the interface between the carbure...

Fuel Tank Spill Return Pipe Gasket for the fuel tank assembly. This gasket seals the joint where the spill return pipe meets the fuel tank, preven...

Copper Injector Sealing Washer in the fuel injection assembly of pre-TDi Land Rover diesel engines. This copper washer seats beneath the injector ...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Front Bumper Tapping Plate fitted behind the front bumper mounting points, providing a reinforced steel backing surface for the bumper fixing bolts...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Nyloc Nut with a 5/8" UNF thread, used as a self-locking fastener in the suspension linkage. The nylon insert deforms around the bolt thread on as...

Brake Shoe Spring for drum brake assemblies. This return spring draws the brake shoes away from the drum surface when the brake pedal is released,...

Split Pin locks a castellated (slotted) nut in place, passing through the nut slots and a cross-drilled hole in the shaft to stop the nut working l...

Upgrade your Series Land Rover suspension with this Polyurethane Shock Absorber Bush Set in black. The set includes 4 pieces, providing everything ...

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

Exhaust Nut in brass, securing exhaust components to their mounting studs. The 5/16" UNF thread and brass construction resist seizing and corrosio...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

Radiator Mounting Bush is the rubber isolation bush that secures the radiator to the body or chassis mounting points, preventing direct metal-to-me...

Door Lock Button Escutcheon is the interior trim surround that frames the sill-mounted door lock button where it passes through the door casing. I...

Inlet Manifold Gasket - Diesel for the 2.25L and 2.5L 4-Cylinder diesel engine. Fitted between the inlet manifold and the cylinder head, this gask...

Copper Sealing Washer for the oil drain plug of the LT77 and R380 manual gearboxes. The washer forms a leak-free seal between the drain plug and t...

Injector Sealing Washer seals each fuel injector into the cylinder head within the diesel fuel injection system, for 200 TDi and 300 TDi turbo-dies...

Brake Shoe Spring for the drum brake assembly on Land Rover vehicles. This return spring pulls the brake shoes back from the drum face after each ...

Rear Stop/Tail Lamp - combined rear stop and tail lamp, supplied as a complete lens and body assembly. It mounts in the rear lamp position and pro...

Ignition Condenser for the contact-breaker (points) ignition system, mounted at the distributor. The condenser is a capacitor wired across the con...

Door Trim Clip for the interior door casing assembly. Fir-tree fastener that secures the door trim casing to the door frame, locating it in the pa...

Bonnet Buffer for the Land Rover bonnet assembly. This rubber buffer mounts to the body structure and provides a cushioned contact point for the u...

Rubber Sealing Ring for gear selector shafts in the LT76 gearbox and LT95 transfer box. In the LT76 gearbox, two rings are fitted per unit, sealin...

Salisbury Joint Washer for the Salisbury rear axle differential. The gasket seats between the differential carrier and the axle casing, sealing th...

Nyloc Nut with an M10 thread - the nylon-insert locking nut used on U-bolt fixings. A nylon collar set into the top of the nut grips the bolt thre...

Exhaust Manifold Gasket for the 3.5L V8 petrol engine. This gasket seals the joint between the exhaust manifold and the cylinder head, preventing ...

Brake Pipe Union for the hydraulic brake system, a female fitting in brass. This union connects a 3/16 inch brake pipe into the brake hydraulic ci...

Clutch Clip - Push Rod to Lever for the hydraulic clutch actuation system. This spring clip secures the clutch slave cylinder push rod to the clut...

U-Bolt Nut - 7/16 BSF for use in the leaf spring suspension assembly. U-bolts clamp the leaf spring pack to the axle casing at the front and rear ...

Stub Axle Oil Seal - Inner

Oil Filter Housing Gasket for the Td5 2.5L five-cylinder turbo diesel engine, sealing the oil filter housing/adaptor to the cylinder block. It sea...

Wheel Nut - secures an alloy road wheel to the hub, forming the threaded clamping interface between the wheel and hub. It uses a wide-stud profile...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...