Price <10

Outer Hub Lock Washer for the front and rear hub assembly on Land Rover solid axles. This lock washer secures the hub bearing retaining nut agains...

Transfer Gear Lever Gaiter for the high/low ratio selector lever on the Series Land Rover transfer box. This rubber gaiter seals around the transf...

Output Shaft Oil Seal seals the front or rear output shaft of the LT76 transfer gearbox, retaining lubricant within the transfer case and preventin...

Drive Member Joint Washer - a sealing gasket fitted between the drive flange and the outer hub on Land Rover Series solid axles. This gasket seals...

Gearbox Gasket Kit - No Seals for the 4-speed manual gearbox and transfer box on Series models. This set supplies the paper and fibre mating gaske...

Brake Drum Screw for the brake drum assembly. This retainer screw secures the brake drum to the wheel hub flange, preventing the drum from displac...

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Drive Shaft Hub Cap for the hub assembly on Land Rover Series vehicles. This cap fits at the outer face of the hub, closing off the drive shaft en...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Gear Lever Gaiter for the transmission tunnel. This flexible boot fits around the base of the gear lever where it passes through the tunnel, sealin...

Drain Plug Washer in copper, used to seal axle differential drain plugs against oil leakage. This copper crush washer seats under the drain plug a...

Brake & Clutch Pedal Pad for the foot pedal assembly. This moulded rubber pad fits over the brake and clutch pedal arm, providing the grip surf...

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Swivel Housing to Stub Axle Joint Washer for the front axle swivel assembly. This sealing washer fits between the swivel housing and the stub axle...

Wheel Cylinder Bleed Screw fits into the bleed nipple port of the wheel cylinder in the drum brake assembly, allowing the hydraulic circuit to be p...

Interior Mirror for Series Land Rover models. Direct-fit interior rear-view mirror providing rearward visibility from the driver's position inside...

Oil Seal for the swivel pin housing on the front axle, sealing against the polished surface of the swivel ball. The seal seats in the rear face of...

Swivel Pin Housing Gasket for the front axle swivel assembly. This gasket seals the mating face between the chrome swivel ball housing and the fro...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Shock absorber bush (eye), anti roll bar bush

Oil Pressure Switch for the engine lubrication system warning circuit. This pressure-sensitive switch threads into the engine block oil gallery an...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Lock nut 3/8" BSF

Drive Flange Gasket

Driving Member Bolt for the axle driving member assembly. This 3/8" BSF x 1-19/32" bolt retains the driving member to the hub assembly. The drivin...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Fuel Sender Unit Gasket for the fuel gauge sender unit fitted to the fuel tank. This gasket seals the joint between the sender unit flange and the...

Exhaust Gasket sealing the exhaust manifold-to-downpipe flange on Series Land Rover 4-cylinder petrol and diesel engines. This four-hole flange ga...

Upgrade your Series Land Rover suspension with this Polyurethane Shock Absorber Bush Set in black. The set includes 4 pieces, providing everything ...

Spring Bush for the leaf spring suspension system on Series Land Rovers. This rubber bush fits into the spring eye at the front fixed mount and re...

Exhaust Nut in brass, securing exhaust components to their mounting studs. The 5/16" UNF thread and brass construction resist seizing and corrosio...

Transfer Box Sump Gasket for the LT76 combined gearbox and transfer box unit used in Series Land Rovers. This flat sealing washer seals the transf...

Ignition Condenser for the contact-breaker (points) ignition system, mounted at the distributor. The condenser is a capacitor wired across the con...

Rubber Sealing Ring for gear selector shafts in the LT76 gearbox and LT95 transfer box. In the LT76 gearbox, two rings are fitted per unit, sealin...

Axle casing oil seal

Brake Pipe Union for the hydraulic brake system, a female fitting in brass. This union connects a 3/16 inch brake pipe into the brake hydraulic ci...

U-Bolt Nut - 7/16 BSF for use in the leaf spring suspension assembly. U-bolts clamp the leaf spring pack to the axle casing at the front and rear ...

Grommet

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Axle Key Washer for the hub nut locking system in the axle assembly. This tab washer seats beneath the axle hub nut, with tabs that locate into ma...

Oil seal

Front Brake Shoe Spring for the front drum brake assembly. This return spring connects the two brake shoes and pulls them back off the drum when th...

Wheel Cylinder Overhaul Kit for front drum brake systems fitted with 11-inch brake drums. This kit provides the necessary parts to overhaul all fo...

Accelerator Spring for the throttle linkage on diesel engines. This return spring acts on the accelerator linkage, drawing the throttle back to th...

Output Shaft Oil Seal seals the front or rear output shaft of the LT76 transfer gearbox, retaining lubricant within the transfer case and preventin...

Anti-Roll Bar Washer used at the anti-roll bar and shock absorber mounting. The washer spreads the clamping load of the retaining nut across the m...

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...