Price <10

Wheel Nut finished in black, used to secure the Terrafirma TF152-series 18x8 modular steel road wheel to the hub. Supplied in a black finish to ma...

Brake Caliper Piston for the front hydraulic disc brake assembly. The piston operates within the caliper bore and transmits hydraulic pressure fro...

Bolt for the upper front suspension arm. This fastener secures the upper front suspension arm within the front axle and suspension assembly.

Vent Panel Stud Bolt for the dashboard air vent panel assembly on Land Rover Defender without air conditioning. This stud bolt secures the dash ve...

Fuel Filler Door Latch secures the fuel tank filler flap in the closed position. The latch holds the filler door flush against the body and releas...

Camshaft Seal for the TDV6 2.7L V6 diesel engine. Seals the camshaft at its exit point from the cylinder head, preventing oil leakage from the cams...

Exhaust Mounting - Rubber is a rubber isolator in the exhaust suspension system, fitted between the exhaust assembly and the vehicle underbody. Th...

Flange Nut An M16 flange nut used on the front suspension arm and stabiliser mountings. The integral flange spreads the clamp load across the moun...

Nut - Plastic - 7mm is a captive plastic fastener for trim and body panel fixing. This plastic nut presses into a 7mm hole in the body or trim pan...

Hex-Head Bolt with Washer, M4 x 14. Fastener used in the front end carrier assembly, securing the front panels, aprons and side members.

Screw - a No. 8 x 1" self-tapping screw used to secure the wing-top air intake grille. It fastens the air intake grille to the top of the front wi...

Trim Clip - retaining clip for interior trim panels. Secures interior trim components such as the instrument panel, glove box and speaker surround...

Self-Tapping Screw and Washer - a 5 x 20mm self-tapping screw with a captive washer, used as a bumper and grille fixing. It secures the radiator g...

Washer used at front suspension arm pivot points, anti-roll bar stabilizer link connections, and front subframe cross-member fastening interfaces, ...

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Domed Nut - retains the dash ventilator (face-level fresh-air vent) in the facia. Used on vehicles without air conditioning. The domed (acorn) for...

Camshaft Screw for the cylinder head and camshaft assembly of the 3.0-litre TDV6 diesel engine. This is a manufacturer-specification retaining scr...

Exhaust Manifold Stud secures the exhaust manifold flange to the cylinder head within the exhaust assembly. This is a double-ended stud, threaded ...

Washer Reservoir Cap closes the filler neck of the windscreen washer fluid reservoir. It seals the reservoir against debris ingress and fluid evap...

Micro Relay is a 20 amp, 4-pin switching relay used within the vehicle electrical system to control a high-current circuit from a low-current signa...

Circlip - Driveshaft Boot is a retaining circlip used within the driveshaft CV joint boot assembly. The circlip secures components within the CV j...

o-ring oil cooler 3,0 TDV6

Rivet Screw - 6.3 x 22mm for securing panels and trim on Land Rover vehicles. This scrivet-type fastener combines a screw thread with a expanding ...

Flanged Hex Bolt, M12 x 70mm. Secures the front wheel hub assembly to the steering knuckle (upright) within the front suspension and hub assembly....

Tow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...

Key Fob Battery - CR2032 3V lithium button cell for Land Rover remote central locking handsets. Fits directly into the remote key fob housing. Rep...

Fusible Link is a high-current circuit-protection device fitted in the engine compartment fuse box. It protects heavy-current wiring and the downs...

Oil filter Freelander TD4 replacement

EGR Inlet Gasket for the exhaust gas recirculation system on the 3.0L V6 turbo diesel engine. Seals the joint at the EGR inlet, where recirculated...

Asy Lamp

Washer - Sealing

Nut - an M8 x 1.25 captive U-spring nut used to mount the air suspension compressor. The spring-steel body clips over the chassis bracket to provi...

Flywheel Bolt with hex head, securing the flywheel to the crankshaft rear flange on the 2.7L V6 Lion turbo diesel fitted with the ZF S6-53 six-spee...

Gasket - Turbocharger Cooling

Torque Converter Screw for the automatic transmission drive coupling. This fixing secures the torque converter to the drive plate, transmitting en...

Thermostat Housing Gasket seals the joint between the thermostat housing (water outlet) and the cylinder head within the cooling system. It mainta...

Rear moulding cap - exterior body trim. The cap closes off the moulding at the junction between the rear bumper and the rear wheelarch moulding, c...

Turbocharger Circlip - retaining clip for the turbocharger actuator on diesel turbocharger installations. It secures the actuator rod to the contr...

Transmission Oil Drain Plug for the ZF 6HP26 and 6HP28 six-speed automatic transmission - Transmission External Components assembly group. M18 x 1...

Amber Bulb - 12V 5W wedge-base (W5W) bulb with an amber envelope, used in the exterior lighting circuit. It serves the direction indicator functio...

Fuel Injection Pump Bolt secures the high-pressure fuel injection pump to its mounting on the engine. It provides the clamping load that holds the...

Nut for the diesel fuel injection pump and timing gear. Secures the drive gear to the high-pressure fuel injection pump on the 2.7L Lion V6 diesel...

O Ring