Range Rover Sport L320 Parts

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Bracket for the tailgate / luggage compartment door assembly. Mounts within the luggage compartment door and its fixings, providing a fixing point...

Cigar Lighter Ring - Illuminated

Height Sensor Jumper Lead for the electronic air suspension system. This connecting lead links a ride-height sensor to the chassis wiring harness,...

Gear Selector Linkage Bush in the floor gear-change assembly of the ZF 6HP26 / 6HP28 6-speed automatic transmission. The bush forms the pivot at t...

Rear Output Shaft Oil Seal for the ZF 6HP26 and 6HP28 six-speed automatic transmission. It seals the point where the output shaft leaves the rear ...

Spring Washer used in the floor-mounted gear change assembly of the ZF 6-speed automatic transmission. It is fitted under the fastener securing th...

Bolt for the floor-mounted gear change assembly of the ZF 6-speed automatic transmission. It secures the gear change mechanism to its mounting on ...

Asy Lamp

Flanged Nut, M8. The integral flange spreads clamp load across the joint face and removes the need for a separate washer. Used in the exhaust syst...

Gasket - Exhaust Pipe

Grommet for the inspection aperture in the rear brake backplate. The backplate carries an access hole through which the parking brake shoe adjuster...

Adjusting Nut is an M17 flanged nut used in the rear suspension toe link assembly. It locks the toe link adjuster at its connection to the rear kn...

Plug for the hydraulic valve block of the Active Anti-Roll Bar system with Roll Stability Control. The valve block contains the solenoid and relie...

Top Radiator Hose from the engine cooling circuit, connecting the radiator to the engine on the upper leg of the circuit. It is a moulded hose, sh...

Stop light switch for the brake pedal box assembly. The switch mounts in the pedal box behind the brake pedal and is operated by the pedal arm as ...

Rear Brake Pad Set for the rear disc brake assembly, supplied as an axle set covering both rear wheels. The pads sit in the rear caliper carrier a...

PCV Valve Service Kit - service parts for the positive crankcase ventilation valve, which sits in the crankcase emission control system on the cyli...

Sealing Ring for the oil level sensor connection at the sump. Seals the oil level sensor wiring connector where it passes through the oil pan (sum...

Oil Pan Retainer for the 3.0L V6 diesel engine. This bracket locates within the oil pan assembly, retaining the oil level indicator (oil level sen...

Seal Kit renews the seals at the hydraulic pipe connections of the Active Cornering Enhancement (ACE) anti-roll bar system. The ACE system uses hy...

Tailgate Lock Control Switch operates the rear tailgate locking mechanism. Located at the luggage compartment, it signals the central locking syste...

Nut is an M16 fastener used in the front suspension. It secures a suspension arm or link joint at the front wishbone assembly, retaining the mount...

Air Suspension Compressor Wiring Repair restores the electrical connection to the air suspension compressor. It replaces the damaged compressor wi...

Solenoid Valve is part of the air suspension compressor assembly, operating within the compressor and air-line circuit. Electrically actuated, it ...

Solenoid Wire - Timing Gear is the wiring lead that connects to the variable valve timing solenoid at the engine timing cover. It is used on the A...

A-Pillar Clip secures the A-pillar interior trim moulding to the body. It is a push-fit retaining clip that holds the plastic A-pillar cover again...

Key Fob Cover Kit replaces the outer casing and rubber button pad of the smart key remote handset. It supplies a new shell and button membrane for...

Brake Fluid for the hydraulic braking and clutch actuation system, supplied in a 1 litre container. A DOT 4 low-viscosity (ESL) fluid formulated f...

Clip retaining the top of the rear air spring within the rear spring and shock absorber assembly. The clip locates and secures the air spring at i...

Radius Arm Bush for the front radius arm, upper position. It press-fits into the arm and forms its pivot at the mounting. Part of the front radius...

Brake Vacuum Hose in the brake servo vacuum circuit of the 3.0L V6 diesel engine, RHD applications. The hose carries vacuum to the brake booster (...

Throttle Body Heater Inlet Hose in the engine cooling circuit of the 5.0L V8 Petrol (AJ133) engine. The hose carries engine coolant to the throttl...

Timing Chain Guide - guides the primary timing chain along its run. Maintains correct alignment and tension on the primary timing drive, keeping c...

Timing Chain Guide - guides the timing chain along its run. Maintains correct alignment and tension on the timing drive, keeping crankshaft-to-cam...

Lever - Bonnet Release

Key Fob End Cap - Chrome is a chrome-finished end cap for the remote key fob, fitting to the end of the fob housing.

Thermostat Tube carries engine coolant between the thermostat housing and the engine on the supercharged 3.0L V6 and 5.0L V8 petrol engines. It run...

Windscreen Washer Jet for the front screen-wash system. It mounts to the bonnet and directs washer fluid from the pump feed onto the windscreen. T...

Heated Windscreen Washer Jet delivers washer fluid onto the front windscreen to clear road film and maintain driver visibility. The jet incorporat...

Throttle Housing Gasket - seals the throttle body to the intake manifold. Forms the air-tight joint between the electronic throttle housing and th...

Timing Gear Bolt - the upper fixing bolt for the timing gear drive on the 3.0L V6 diesel engine. It secures the upper timing gear within the engin...

Idler Pulley guides and routes the accessory drive belt at the front of the engine. It maintains belt alignment and wrap across the auxiliary (sec...