Range Rover Sport L320 Parts

Brake Caliper Locating Pin Kit for the sliding brake caliper. The guide pins let the caliper float on its carrier bracket so both brake pads wear ...

Immobiliser Transceiver for the vehicle anti-theft (immobiliser) system. This is the transceiver aerial that reads the transponder in the key at t...

Axle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...

Piston ring set for the 5.0L V8 AJ133 petrol engine, both naturally aspirated and supercharged, in +0.50 mm oversize. One set covers a single pist...

Piston Ring Set for the 5.0L V8 AJ133 petrol engine, supplied at standard bore size. The ring pack seals the combustion chamber against the cylind...

Thermostat Housing Gasket seals the joint between the thermostat housing (water outlet) and the cylinder head within the cooling system. It mainta...

Brake Disc Retaining Screw that locates the brake disc against the wheel hub flange, holding the disc square and in position while the caliper and ...

Overflow Container Cap for the cooling system expansion (overflow) reservoir. The cap seals the coolant expansion tank and maintains system pressu...

Head Gasket for the right-hand cylinder bank of the 4.4L DOHC V8 turbo diesel (TDV8) engine. Seals the joint between the right-hand cylinder head ...

Cylinder Head Gasket for the left-hand cylinder head of the 4.4L DOHC DITC V8 diesel (TDV8) engine. Seals the joint between the left-hand cylinder...

Head Gasket for the right-hand cylinder bank of the 4.4L DOHC V8 turbo diesel (TDV8) engine. Seals the joint between the right-hand cylinder head ...

Cylinder Head Gasket for the left-hand cylinder head of the 4.4L DOHC DITC V8 diesel (TDV8) engine. Seals the joint between the left-hand cylinder...

Final Drive Lubricant - a fully synthetic 75W-90 gear oil meeting API GL5, supplied in a 4 litre pack. Specified for the front and rear final driv...

Front Brake Disc, internally vented, for the front braking system. The disc mounts to the front hub and provides the friction surface acted on by ...

Brake Pad Fitting Kit - Front - caliper hardware set used when renewing the front brake pads, covering the guide bush and seal components that loca...

Camshaft Position Sensor mounted in the timing gear cover, reading the toothed target on the camshaft drive to give the engine control module a dir...

Thermostat Housing for the 5.0-litre AJ133 V8 petrol engine, part of the engine cooling circuit. The housing seats the coolant thermostat and form...

Cylinder Head Gasket seals the joint between the cylinder head and the engine block on the 3.0L V6 turbo diesel engine, containing combustion press...

Cylinder Head Gasket seals the joint between the cylinder head and the engine block on the 3.0L V6 turbo diesel engine, containing combustion press...

Keyless Entry and Start Aerial is the receiver antenna for the passive keyless entry and push-button start system, part of the vehicle's anti-theft...

Remote Control Receiver is part of the vehicle anti-theft alarm system, operating on the 433MHz radio frequency band. It receives the coded radio ...

M6 x 45mm bolt from the Exhaust Gas Recirculation (EGR) system of the 3.0L V6 diesel engine. Used to secure EGR components to their mounting faces...

Turbocharger Circlip - retaining clip for the turbocharger actuator on diesel turbocharger installations. It secures the actuator rod to the contr...

Gasket - Oil Filter to Block seals the joint between the oil filter housing and the cylinder block, within the Oil Cooler and Filter assembly. It ...

O-Ring for the oil pump inlet tube, part of the oil pump, sump and filter assembly. It seals the joint at the oil pump inlet (pick-up) tube, keepi...

Cylinder Head Gasket seals the joint between the cylinder head and the engine block on the 3.0L V6 turbo diesel engine, containing combustion press...

Charge Air Pressure Sensor measuring the pressure of the compressed intake charge at the secondary compressor outlet, within the intercooler, air d...

Screw, M6 x 38mm, from the timing gear assembly - timing chains, tensioners and guides, and the auxiliary drive. It retains the chain guide in pos...

D3S xenon headlamp bulb, supplied with its igniter, for headlamp units originally built as bi-xenon or adaptive xenon assemblies. D3S is a mercury...

Size/Diameter: M8 10.9

Front Brake Pad Set - friction pads for the front disc brake calipers, forming part of the front foundation braking assembly. The pads are carried...

Lower Timing Gear Screw - a fixing screw in the engine timing drive, retaining the lower timing gear. Used on the 3.0 V6 diesel engine (and the 2....

Wheel Nut Set - set of twenty wheel nuts, sufficient for four five-stud road wheels. Each nut clamps the road wheel against the hub face on the wh...

Drive Belt Tensioner - maintains correct tension on the front accessory (auxiliary) drive belt. The sprung tensioner assembly applies constant loa...

Flanged Hex Bolt M10 x 25mm - a threaded fastener used in the engine timing gear and turbocharger mounting assemblies. The integral flange under t...

Front Brake Pad Set - friction pads for the front disc brake calipers, forming part of the front foundation braking assembly. The pads are carried...

Front Brake Pad Set - friction pads for the front disc brake calipers, forming part of the front foundation braking assembly. The pads are carried...

Crankshaft position sensor for 3.0L V6 and 4.4L V8 diesel engines, part of the engine management sensing circuit. The sensor sits at the crankshaf...

Crankshaft position sensor for 3.0L V6 and 4.4L V8 diesel engines, part of the engine management sensing circuit. The sensor sits at the crankshaf...

Oil Cooler Assembly for the 5.0-litre supercharged V8 petrol engine (AJ133). It forms part of the engine lubrication circuit, transferring heat fro...

Auxiliary Water Pump - electric coolant circulation pump for the fuel-fired booster heater circuit. The pump draws coolant through the fuel-burnin...

Oil Seal for the ZF transfer case. Seals a rotating shaft on the transfer case to retain lubricant and exclude contaminants.

Drain Plug Washer for the transfer box drain and level plugs. The washer seals the plug against the transfer box casing and is replaced each time ...

Cylinder Block Core Plug Seal sealing a core plug aperture in the cylinder block. It seals a casting core plug opening in the block, preventing co...