for Discounts / VAT
for Discounts & Correct VAT
Replacement parts for the Range Rover Velar L560, built at Solihull from 2017 on the JLR iQ[Al] aluminium platform. Covers all Ingenium diesel and petrol variants, MHEV, PHEV, and ZF 8-speed automatic configurations.
O-Ring for the oil pump outlet tube, sealing the pressurised feed within the oil pump, sump and filter assembly. The outlet tube carries oil from ...
View full detailsFuel Balance Pipe for the 3.0L V6 diesel engine, part of the fuel injectors and pipes group within the engine fuel system. The pipe runs across th...
View full detailsOil Separator Reservoir for the 3.0L V6 diesel, part of the crankcase ventilation circuit within the engine emission control system. Crankcase blo...
View full detailsFuel Injector Pipe is a rigid high-pressure line in the common-rail fuel injection system, forming part of the fuel injectors and pipes assembly on...
View full detailsSealing ring kit for the engine oil cooler and oil filter housing connections on the 3.0L V6 diesel. The rings seal the oil transfer joints betwee...
View full detailsCylinder Head Gasket seals the joint between the cylinder head and the engine block on the 3.0L V6 turbo diesel engine, containing combustion press...
View full detailsOil Separator Reservoir for the 3.0L V6 diesel, part of the crankcase ventilation circuit within the engine emission control system. Crankcase blo...
View full detailsTiming Gear Bolt - Lower is the M16 x 70mm flanged hex bolt that retains the lower timing gear on the crankshaft. It is also listed as the cranksha...
View full detailsO-Ring for the oil pump outlet tube, sealing the pressurised feed within the oil pump, sump and filter assembly. The outlet tube carries oil from ...
View full detailsTorque Converter Seal Kit - ZF 8-Speed
Cylinder Head Gasket seals the joint between the cylinder head and the engine block on the 3.0L V6 turbo diesel engine, containing combustion press...
View full detailsWater Manifold Gasket for the engine cooling and heater circuit - it seals the water manifold tube where it leaves the cylinder block and feeds the...
View full detailsBrake Pads - Front - Less Springs - friction pads for the front axle, supplied as a complete axle set (one set per axle). The pads locate in the f...
View full detailsOil Seal for the oil level sensor where it passes through the wall of the oil pan (sump). The sensor is retained in the sump and this ring forms t...
View full detailsPlastic Rivet is a push-fit fastener that secures front engine-compartment insulation panels to the body. It locates into a pre-formed panel hole t...
View full detailsCylinder Head Bolt secures the cylinder head to the engine block on V6 and V8 petrol engines. Threaded M11 x 178 mm. Twenty bolts are required per...
View full detailsExhaust Gas Pressure Sensor for the diesel particulate filter stage of the exhaust aftertreatment system. The sensor connects to the exhaust by st...
View full detailsExhaust Gas Pressure Sensor is the differential pressure sensor for the Diesel Particulate Filter (DPF) on the 2.0L Ingenium four-cylinder diesel e...
View full detailsExhaust Gas Pressure Sensor - pressure sensor in the exhaust gas recirculation circuit, mounted on the right-hand side of the engine. It measures ...
View full detailsTyre Pressure Sensor (TPMS) for the direct tyre pressure monitoring system. Fitted at the wheel valve inside the tyre, it measures tyre pressure an...
View full detailsTyre Pressure Sensor (TPMS) for the direct tyre pressure monitoring system. Fitted at the wheel valve inside the tyre, it measures tyre pressure an...
View full detailsCylinder Head Gasket seals the cylinder head to the engine block on the 2.0L Ingenium four-cylinder diesel engine (AJ200 series). It seals the com...
View full detailsCylinder Head Gasket seals the cylinder head to the engine block on the 2.0L Ingenium four-cylinder diesel engine (AJ200 series). It seals the com...
View full detailsKnock Sensor detects engine detonation (knock) on the 2.0L Ingenium four-cylinder petrol engine. Bolted to the cylinder block, it converts combust...
View full detailsAutomatic Transmission Fluid (ATF), supplied in a 1 litre container. Specified for the automatic transmission and, where applicable, the power ste...
View full detailsAutomatic Transmission Fluid (ATF), supplied in a 1 litre container. Specified for the automatic transmission and, where applicable, the power ste...
View full detailsAutomatic Transmission Fluid (ATF), supplied in a 1 litre container. Specified for the automatic transmission and, where applicable, the power ste...
View full detailsCylinder Head Bolt Kit for the 2.0L Ingenium diesel engine (AJ200 / AJ20D4). Supplied as a set for renewing the cylinder head bolts when the cylin...
View full detailsCylinder Head Bolt for the 2.0L Ingenium diesel engine (AJ200 / AJ20D4), securing the cylinder head to the engine block. Supplied as a single bolt...
View full detailsFuel Pressure Sensor mounted in the fuel supply manifold (common rail). The sensor measures the pressure of fuel in the rail and reports it to the...
View full detailsTiming Chain Tensioner, part of the timing chain drive within the timing cover. It applies controlled load to the timing chain guide to keep the ch...
View full detailsManifold - Heater
Track Rod End for the steering linkage. The track rod end is the ball-jointed connection at the outer end of the steering tie rod, linking the ste...
View full detailsTrack Rod End for the steering linkage. The track rod end is the ball-jointed connection at the outer end of the steering tie rod, linking the ste...
View full detailsFuel Pressure Regulator (fuel pressure control valve) for the diesel high-pressure fuel injection system. Mounted on the high-pressure fuel pump, i...
View full detailsInjection Pump Leak-Off Tube for the diesel fuel injection system, connecting to the injection pump. The tube returns leak-off (spill) fuel from t...
View full detailsFuel Pressure Regulator fitted to the high-pressure diesel injection pump. The regulator controls the pressure of fuel delivered by the injection ...
View full detailsCylinder Head Gasket for the 2.0L I4 (AJ200 / AJ20D4) diesel engine. It seals the joint between the cylinder head and the engine block, sealing com...
View full detailsCylinder Head Gasket for the 2.0L I4 (AJ200 / AJ20D4) diesel engine. It seals the joint between the cylinder head and the engine block, sealing com...
View full detailsTyre Pressure Sensor - wheel-mounted sensor forming part of the Tyre Pressure Monitoring System (TPMS). The sensor is fitted at the valve position...
View full detailsIgnition Coil for the 2.0L four-cylinder petrol engine (AJ200 / AJ20P4, including PHEV). This is a coil-on-plug unit that mounts directly on the sp...
View full detailsTrack Rod End ball joint for the steering linkage. It forms the adjustable pivoting connection at the outer end of the track rod, transmitting stee...
View full detailsImmobiliser Transceiver for the vehicle anti-theft (immobiliser) system. This is the transceiver aerial that reads the transponder in the key at t...
View full detailsAxle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...
View full detailsPiston ring set for the 5.0L V8 AJ133 petrol engine, both naturally aspirated and supercharged, in +0.50 mm oversize. One set covers a single pist...
View full detailsPiston Ring Set for the 5.0L V8 AJ133 petrol engine, supplied at standard bore size. The ring pack seals the combustion chamber against the cylind...
View full detailsThermostat Housing Gasket seals the joint between the thermostat housing (water outlet) and the cylinder head within the cooling system. It mainta...
View full detailsABS Sensor (wheel speed sensor) for the anti-lock braking system, rear axle. The sensor monitors wheel rotation speed and reports it to the ABS co...
View full detailsThe Velar L560 has been produced with a wider engine range than most single-generation Land Rover models, and correct part fitment depends on knowing your engine code and model year. The pre-facelift range ran from 2017 to 2020 and included the Ingenium D180 and D240 four-cylinder diesels, the twin-turbo D300 and D275 V6 diesels, the P250 and P300 four-cylinder petrols, the P340 and P380 supercharged V6 petrols, and the limited SVAutobiography Dynamic with the 5.0-litre V8. From September 2020, the engine range was revised. The D200 replaced the D180 with mild hybrid assistance, the P400 Ingenium turbocharged inline-six replaced the P380 V6, and the P400e PHEV was introduced, combining a 2.0-litre Ingenium petrol unit with a 106 kW permanent magnet synchronous motor and a 17.1 kWh lithium-ion battery. A mild exterior and infotainment refresh was applied from 2023. Fitment differences exist between pre-facelift, post-September-2020, and post-2023 vehicles, particularly for engine ancillaries, emissions components, and hybrid system parts.
All four-cylinder variants use the ZF 8HP45 eight-speed automatic gearbox. All six-cylinder variants use the heavier-duty ZF 8HP70 unit. Gearbox-related parts must be matched to the correct variant.
Engine specifications and ZF 8HP transmission variant assignments confirmed against ZF Group 8HP-series technical data and JLR engine specifications as documented in the Range Rover Velar L560 launch technical record.
The Velar L560 shares its iQ[Al] D7a aluminium platform with the Jaguar F-Pace, Jaguar XF (X260), and Jaguar XE. This means a number of underbody, suspension geometry, and fastener components are shared across those vehicles. Workshops sourcing parts for the Velar may find that certain subframe components, suspension bushings, and general hardware are catalogued across both JLR and Jaguar parts systems. This does not apply to powertrain-specific or model-specific body parts. Always confirm part numbers against the Velar L560 catalogue before ordering on the basis of platform compatibility alone.
Fitment ConfirmationThe Velar L560's broad engine and drivetrain range means that year-of-manufacture alone is not sufficient to confirm fitment for many parts. The Vehicle Identification Number (VIN) contains the production sequence, engine code, and build specification and is the most reliable way to confirm the correct part for your vehicle. The VIN is located on the windscreen lower edge (driver's side on most LHD markets, passenger's side on RHD markets) and on the vehicle's identification plate in the engine bay. If you are unsure whether a listed part fits your specific Velar, contact Budget Parts with your VIN before ordering.
Related CollectionsFor parts covering other Range Rover generations or the broader Range Rover family, see Range Rover parts.
For Velar-adjacent models built on the same generation platform, the Range Rover Evoque L538 parts collection covers the previous Evoque generation and the Range Rover Sport L494 parts collection covers the Sport generation sharing the same era of Ingenium engine development.
Technical GuidesThe following article from the Budget Parts technical library covers the Velar L560 platform, engines, and ownership considerations relevant to parts selection.
A technical reference covering the iQ[Al] D7a platform, Ingenium engine range, AWD systems, and the service considerations that affect accurate parts selection on the Velar L560.
Range Rover Velar L560 guide →The Range Rover Velar L560 entered production in 2017 and is the only current generation of the Velar. A mild facelift was introduced in 2023, primarily affecting exterior styling and the infotainment system. A second-generation Velar on a new electric-only platform is announced for production from 2027 and is a separate vehicle entirely. Parts on this page cover the L560 generation only, from 2017 to present.
The engine code is stamped on the engine block and is also encoded in your VIN. For diesel variants, the main codes in service are D180 (2017 to 2020), D200 (2020 onwards, MHEV), D240 (2017 to 2020), D300 V6 (2017 to 2020), and D300 Ingenium inline-six (2020 onwards). For petrol variants, the main codes are P250, P300 (2017 to 2020), P340, P380 (2017 to 2020), P400 MHEV (2020 onwards), and P400e PHEV (2020 onwards). Engine-specific parts including timing components, injectors, and turbo ancillaries must be matched to the correct code.
Yes, in part. Both vehicles are built on the JLR iQ[Al] D7a aluminium platform, sharing the same wheelbase of 2,874 mm and common underbody architecture. This means certain suspension geometry components, subframe hardware, and general fasteners are shared across the catalogue. However, powertrain-specific parts, body panels, and model-specific electronics are not interchangeable. Workshops cross-referencing parts between the Velar and F-Pace should always verify against the Velar L560 part number before ordering.
All Velar L560 variants use a ZF 8-speed automatic transmission. Four-cylinder engines (diesel and petrol) are paired with the ZF 8HP45 unit. Six-cylinder engines, including the P380, P400, D300 V6, and D300 I6, are paired with the heavier-duty ZF 8HP70 unit. Gearbox-related parts, including oil, filter kits, solenoids, and sensors, must be matched to the correct 8HP variant for your engine.
Genuine parts carry the official Land Rover part number and are manufactured to JLR specification. OEM parts are produced by the same manufacturer that supplied the component to JLR originally, meeting the same specification without the Land Rover branding. Aftermarket parts are independently manufactured and are suitable for wear items and general maintenance where exact OEM specification is not required. All three tiers are available through Budget Parts for the Velar L560.
Use your VIN. The 17-character VIN encodes your engine code, production year, and build specification and is the most reliable way to confirm fitment before ordering. The VIN is located on the lower edge of the windscreen (driver's side on most LHD markets, passenger's side on RHD markets) and on the identification plate in the engine bay. If you need help confirming fitment, contact Budget Parts with your VIN and the part reference you are considering.
Yes. The collection includes parts relevant to the P400e PHEV (introduced September 2020) and D200 and P400 MHEV variants. These include hybrid system ancillaries, AdBlue components for diesel MHEV variants, and Ingenium engine parts common to the hybrid-equipped models. Specific high-voltage battery components are not included in this collection. Contact Budget Parts if you are sourcing parts for a specific PHEV or MHEV repair and are unsure whether a listed part applies to your variant.